AFE4950
- Supports simultaneous and synchronized acquisition of up to 24 PPG and a single-lead ECG signal.
- Flexible allocation of 8 LED, 4 PD in each phase
- ECG signal chain:
- 1-lead ECG signal acquisition up to 2 kHz
- RLD output to drive a third electrode
- Input noise : 0.7 µV-rms
- Supports up to ±0.65 V differential DC offset and +/-0.55 V common mode range
- Programmable INA gain: 11, 21
- High-pass filter with quick saturation recovery
- Integrated 300 Hz anti-aliasing low pass filter
- AC, DC lead-off detect: 2.9 nA to 92.5 nA
- Low power continuous lead-on detection
- Impedance signal chain
- Continuous low-power monitoring of impedance between 2 electrodes
- 7 MΩ range
- 300 Ω noise on 620 kΩ
- PPG Transmitter:
- 8-Bit Programmable LED Current with range adjustable from 25 mA to 250 mA
- Mode to fire two LEDs in parallel
- Support of 8 LEDs in Common Anode configuration for SpO2, Multi-Wavelength HRM
- PPG Receiver:
- 2 parallel receivers (two sets of TIA/ filter)
- Supports 4 Time-Multiplexed Photodiode Inputs to each Receiver
- 8-bit Ambient Offset subtraction at each TIA input with 256 µA range
- 8-bit LED Offset Subtraction DAC with 64 µA range
- Automatic ambient cancellation and dynamic LED DC cancellation at TIA input
- Ambient rejection close to 100 dB up to 10 Hz
- Noise filtering with programmable bandwidth
- Trans-impedance Gain: 3.7 kΩ to 1 MΩ
- Accurate, Continuous Heart-Rate Monitoring:
- System SNR up to 109-dB at 16 µA PD current
- Low Current for Continuous Operation on a Wearable Device with a Typical Value: 15-µA for an LED, 20-µA for the Receiver
- External clock and internal oscillator modes
- Acquire data synchronized with system master clock
- FIFO with 256-sample Depth
- SPI, I2C interfaces: Selectable by pin
- 2.6-mm × 2.5-mm DSBGA, 0.4-mm Pitch
- Supplies: Rx:1.7-1.9V (LDO Bypass); 1.9-3.6V (LDO Enabled), Tx:3-5.5V, IO:1.7-RX_SUP
The AFE4950 device is an analog front-end (AFE) for synchronized signal acquisition of PPG and ECG signals. The device can also be used for optical bio-sensing applications, such as heart-rate monitoring (HRM) and saturation of peripheral capillary oxygen (SpO2). The ECG signal chain supports 2- and 3-electrode configurations and has an integrated Right leg drive (RLD) buffer. The ECG signal chain can also be used to do a continuous, low-power monitoring of the impedance between pair of electrodes.
추가 정보 요청
전체 데이터시트 및 기타 설계 리소스는 NDA에 따라 제공됩니다. 지금 요청
기술 문서
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | AFE4950 Ultra-Small, Integrated AFE for Wearable Optical Heart-Rate Monitoring, SpO2 and Electrical Bio-sensing datasheet (Rev. B) | PDF | HTML | 2021/07/15 |
Product overview | ECG and Cuffless Blood Pressure Monitoring With Integrated AFE | PDF | HTML | 2023/10/30 | |
Product overview | Photoplethysmography (PPG) With Integrated AFE for Optical Biosensing | PDF | HTML | 2023/10/30 | |
Application brief | ECG Signal Acquisition on Wearables | PDF | HTML | 2022/11/15 | |
Application brief | Measuring Oxygen Saturation (SpO2) on Wearables | PDF | HTML | 2022/11/14 | |
Application brief | Optical Heart Rate Monitoring (OHRM) on Wearables | PDF | HTML | 2022/11/14 | |
Application brief | Cuffless Blood Pressure Monitoring on Wearables | PDF | HTML | 2022/11/09 | |
Technical article | Solving 5 challenges of ECG signal acquisition in wearables | PDF | HTML | 2021/07/21 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
AFE4950EVM — 웨어러블 광학 심박수 모니터링을 위한 AFE4950 초소형 통합 AFE 평가 모듈
The AFE4950 evaluation module (EVM) is designed to expedite evaluation and system-development activities related to the AFE4950 product. AFE4950 is an analog front end (AFE) for synchronized signal acquisition of PPG and ECG signals. AFE4950 can also be used for optical biosensing applications, (...)
BSECUR-3P-ALGORITHMS — B SECUR ECG Algorithms and Electrode Design Services
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
패키지 | 핀 | 다운로드 |
---|---|---|
DSBGA (YBG) | 36 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치