PCA9557
- Low Standby Current Consumption of 1 μA Max
- I2C to Parallel Port Expander
- Operating Power-Supply Voltage Range of 2.3 V to 5.5 V
- 5-V Tolerant I/O Ports
- 400-kHz Fast I2C Bus
- Three Hardware Address Pins Allow for Use of up to Eight Devices on I2C/SMBus
- Lower-Voltage Higher-Performance Migration Path for PCA9556
- Input/Output Configuration Register
- Polarity Inversion Register
- Active-Low Reset Input
- Internal Power-On Reset
- High-Impedance Open Drain on P0
- Power Up With All Channels Configured as Inputs
- No Glitch on Power Up
- Noise Filter on SCL/SDA Inputs
- Latched Outputs With High Current Drive Maximum Capability for Directly Driving LEDs
- Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
- ESD Protection Exceeds JESD 22
- 2000-V Human-Body Model (A114-A)
- 200-V Machine Model (A115-A)
- 1000-V Charged-Device Model (C101)
All trademarks are the property of their respective owners.
This 8-bit I/O expander for the two-line bidirectional bus (I2C) is designed for 2.3-V to 5.5-V VCC operation. The device provides general-purpose remote I/O expansion for most microcontroller families via the I2C interface [serial clock (SCL) and serial data (SDA)].
The PCA9557 consists of one 8-bit configuration (input or output selection), input port, output port, and polarity inversion (active-high) registers. At power on, the I/Os are configured as inputs. However, the system master can enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or output is kept in the corresponding input or output register. The polarity of the input port register can be inverted with the polarity inversion register. All registers can be read by the system master.
The device outputs (latched) have high-current drive capability for directly driving LEDs. The device has low current consumption.
The system master can reset the PCA9557 in the event of a timeout or other improper operation by asserting a low in the active-low reset (RESET) input. The power-on reset puts the registers in their default state and initializes the I2C/SMBus state machine. Asserting RESET causes the same reset/initialization to occur without depowering the part.
Three hardware pins (A0, A1, and A2) are used to program and vary the fixed I2C address, allowing up to eight devices to share the same I2C bus or SMBus.
기술 문서
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | PCA9557 Remote 8-Bit I2C and SMBus Low-Power I/O Expander datasheet (Rev. J) | 2014/06/12 | |
| Application note | I2C Dynamic Addressing | 2019/04/25 | ||
| Selection guide | Logic Guide (Rev. AB) | 2017/06/12 | ||
| Application note | Choosing the Correct I2C Device for New Designs | PDF | HTML | 2016/09/07 | |
| Application note | Understanding and Interpreting Standard-Logic Data Sheets (Rev. C) | 2015/12/02 | ||
| Application note | Understanding the I2C Bus | PDF | HTML | 2015/06/30 | |
| Application note | Maximum Clock Frequency of I2C Bus Using Repeaters | 2015/05/15 | ||
| Application note | I2C Bus Pull-Up Resistor Calculation | PDF | HTML | 2015/02/13 | |
| Application note | Programming Fun Lights With TI's TCA6507 | 2007/11/30 | ||
| Application note | Semiconductor Packing Material Electrostatic Discharge (ESD) Protection | 2004/07/08 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
I2C-DESIGNER — I2C 디자이너 툴
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
TINA-TI — SPICE 기반 아날로그 시뮬레이션 프로그램
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| SOIC (D) | 16 | 옵션 보기 |
| SSOP (DB) | 16 | 옵션 보기 |
| TSSOP (PW) | 16 | 옵션 보기 |
| TVSOP (DGV) | 16 | 옵션 보기 |
| VQFN (RGV) | 16 | 옵션 보기 |
| VQFN (RGY) | 16 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.