TAS5751M
- Audio Input/Output
- One-Stereo Serial Audio Input
- Supports 44.1-kHz and 48-kHz Sample Rates (LJ/RJ/I²S)
- Supports 3-Wire I²S Mode (no MCLK required)
- Automatic Audio Port Rate Detection
- Supports BTL and PBTL Configuration
- POUT = 25 W at 10% THD+N
- PVDD = 20 V, 8 Ω, 1 kHz
- Audio/PWM Processing
- Independent Channel Volume Controls With Gain of 24 dB to Mute in 0.125-dB Steps
- Programmable Three-Band Automatic Gain Limiting (AGL)
- 20 Programmable Biquads for Speaker EQ and Other Audio-Processing Features
- General Features
- 106-dB SNR, A-Weighted, Referenced to Full Scale (0 dB)
- I²C Serial Control Interface w/ two Addresses
- Thermal, Short-Circuit, and Undervoltage Protection
- Up to 90% Efficient
- AD, BD, and Ternary Modulation
- PWM Level Meter
The TAS5751M device is an efficient, digital-input audio amplifier for driving stereo speakers configured as a bridge tied load (BTL). In parallel bridge tied load (PBTL) in can produce higher power by driving the parallel outputs into a single lower impedance load. One serial data input allows processing of up to two discrete audio channels and seamless integration to most digital audio processors and MPEG decoders. The device accepts a wide range of input data and data rates. A fully programmable data path routes these channels to the internal speaker drivers.
The TAS5751M device is a slave-only device receiving all clocks from external sources. The TAS5751M device operates with a PWM carrier between a 384-kHz switching rate and a 288-kHz switching rate, depending on the input sample rate. Oversampling combined with a fourth-order noise shaper provides a flat noise floor and excellent dynamic range from 20 Hz to 20 kHz.
추가 정보 요청
PurePath™ Console 3, TAS5751M GUI 및 기타 설계 리소스를 사용할 수 있습니다. 지금 요청
기술 문서
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | TAS5751M - Digital Input Audio Power Amplifier with EQ and 3-Band AGL datasheet (Rev. B) | PDF | HTML | 2018/05/15 |
More literature | TAS5751MEVM Quick Start Guide (Rev. A) | 2016/07/20 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
PUREPATH-CMBEVM — 오디오 시스템 설계 및 개발을 위한 PurePath™ 콘솔 마더보드
The PurePath™ Console Motherboard (PurePath-CMBEVM) provides a seamless interface between Ti’s latest PurePath Console GUI to supported TI’s digital and mixed-signal audio evaluation modules, including audio amplifiers and audio converters.
The PurePath-CMBEVM is shipped as a stand-alone board. It (...)
TAS5751MEVM — TAS5751M 디지털 입력, 개방형 루프 클래스 D 오디오 증폭기 평가 모듈
The TAS5751MEVM allows evaluation of the TAS5751M, I2S-input, open-loop amplifier from Texas Instruments. The evaluation module is populated with two TAS5751M devices, one configured for two channel operation and one configured for mono operation. The TAS5751M combines a PWM processor with an (...)
PUREPATHCONSOLE — 오디오 시스템 설계 및 개발을 위한 PurePath™ 콘솔 그래픽 개발 제품군
PurePath Console’s (...)
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
패키지 | 핀 | 다운로드 |
---|---|---|
HTSSOP (DCA) | 48 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.