TPA2001D2
- Modulation Scheme Optimized to Operate Without a Filter
- 1 W Into 8-
Speakers (THD+N< 0.4%) - < 0.08% THD+N at 0.5 W, 1 kHz, Into 8- Load
- Extremely Efficient 3rd Generation 5-V Class-D Technology:
- \x96 Low Supply Current (No Filter) ...8 mA
- \x96 Low Supply Current (Filter) ...15 mA
- \x96 Low Shutdown Current ...1 uA
- \x96 Low Noise Floor ...56 uV RMS
- \x96 Maximum Efficiency Into 8 , 75 \x96 85%
- \x96 4 Internal Gain Settings ...8 \x96 23.5 dB
- \x96 PSRR . . . \x9677 dB
- Integrated Depop Circuitry
- Short-Circuit Protection (Short to Battery, Ground, and Load)
- \x9640°C to 85°C Operating Temperature Range
PowerPAD is a trademark of Texas Instruments.
The TPA2001D2 is the third generation 5-V class-D amplifier from Texas Instruments. Improvements to previous generation devices include: lower supply current, lower noise floor, better efficiency, four different gain settings, smaller packaging, and fewer external components. The most significant advancement with this device is its modulation scheme that allows the amplifier to operate without the output filter. Eliminating the output filter saves the user approximately 30% in system cost and 75% in PCB area.
The TPA2001D2 is a monolithic class-D power IC stereo audio amplifier, using the high switching speed of power MOSFET transistors. These transistors reproduce the analog signal through high-frequency switching of the output stage. The TPA2001D2 is configured as a bridge-tied load (BTL) amplifier capable of delivering greater than 1 W of continuous average power into an 8- load at 1 kHz, the typical
THD+N is less than 0.08%.
A BTL configuration eliminates the need for external coupling capacitors on the output. Low supply current of 8 mA makes the device ideal for battery-powered applications. Protection circuitry increases device reliability: thermal, over-current, and under-voltage shutdown.
Efficient class-D modulation enables the TPA2001D2 to operate at full power into 8- loads at an ambient temperature of 85°C.
기술 문서
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | 1-W Filterless Stereo Class-D Audio Power Amplifier datasheet (Rev. A) | 2000/04/25 | |
| Application note | Layout Guidelines For TPA300x Series Parts (Rev. A) | 2020/06/24 | ||
| Application note | Measuring Class-D Amplifiers for Audio Speaker Overstress Testing | 2005/10/28 | ||
| EVM User's guide | TPA2001D2EVM - User Guide | 2000/11/01 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TPA2001D2EVM — TPA2001D2 EVM(평가 모듈)
The TPA2001D2 is a stereo Class-D audio power amplifier that does not require an output filter. The TPA2001D2 has an output power of 1-W RMS into 4 Ohm speakers. By eliminating the need for bulky LC output filters, the TPA2001D2 audio power amplifier enables designers to reduce board space and (...)
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
| 패키지 | 핀 | 다운로드 |
|---|---|---|
| HTSSOP (PWP) | 24 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치