SBAS670B July   2014  – April 2017 ADC3441 , ADC3442 , ADC3443 , ADC3444

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Device Comparison Table
  6. Pin Configuration and Functions
  7. Specifications
    1. 7.1  Absolute Maximum Ratings
    2. 7.2  ESD Ratings
    3. 7.3  Recommended Operating Conditions
    4. 7.4  Thermal Information
    5. 7.5  Electrical Characteristics: General
    6. 7.6  Electrical Characteristics: ADC3441, ADC3442
    7. 7.7  Electrical Characteristics: ADC3443, ADC3444
    8. 7.8  AC Performance: ADC3441
    9. 7.9  AC Performance: ADC3442
    10. 7.10 AC Performance: ADC3443
    11. 7.11 AC Performance: ADC3444
    12. 7.12 Digital Characteristics
    13. 7.13 Timing Requirements: General
    14. 7.14 Timing Requirements: LVDS Output
    15. 7.15 Typical Characteristics: ADC3441
    16. 7.16 Typical Characteristics: ADC3442
    17. 7.17 Typical Characteristics: ADC3443
    18. 7.18 Typical Characteristics: ADC3444
    19. 7.19 Typical Characteristics: Common
    20. 7.20 Typical Characteristics: Contour
  8. Parameter Measurement Information
    1. 8.1 Timing Diagrams
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Analog Inputs
      2. 9.3.2 Clock Input
        1. 9.3.2.1 Using the SYSREF Input
        2. 9.3.2.2 SNR and Clock Jitter
      3. 9.3.3 Digital Output Interface
        1. 9.3.3.1 One-Wire Interface: 14x Serialization
        2. 9.3.3.2 Two-Wire Interface: 7x Serialization
    4. 9.4 Device Functional Modes
      1. 9.4.1 Input Clock Divider
      2. 9.4.2 Chopper Functionality
      3. 9.4.3 Power-Down Control
      4. 9.4.4 Internal Dither Algorithm
      5. 9.4.5 Summary of Performance Mode Registers
    5. 9.5 Programming
      1. 9.5.1 Serial Interface
        1. 9.5.1.1 Register Initialization
          1. 9.5.1.1.1 Serial Register Write
          2. 9.5.1.1.2 Serial Register Readout
      2. 9.5.2 ADC3441 Power-Up Requirements
    6. 9.6 Register Maps
      1. 9.6.1 Serial Register Description
        1. 9.6.1.1  Register 01h (address = 01h)
        2. 9.6.1.2  Register 03h (address = 03h)
        3. 9.6.1.3  Register 04h (address = 04h)
        4. 9.6.1.4  Register 05h (address = 05h)
        5. 9.6.1.5  Register 06h (address = 06h)
        6. 9.6.1.6  Register 07h (address = 07h)
        7. 9.6.1.7  Register 09h (address = 09h)
        8. 9.6.1.8  Register 0Ah (address = 0Ah)
        9. 9.6.1.9  Register 0Bh (address = 0Bh)
        10. 9.6.1.10 Register 13h (address = 13h)
        11. 9.6.1.11 Register 0Eh (address = 0Eh)
        12. 9.6.1.12 Register 0Fh (address = 0Fh)
        13. 9.6.1.13 Register 15h (address = 15h)
        14. 9.6.1.14 Register 25h (address = 25h)
        15. 9.6.1.15 Register 27h (address = 27h)
        16. 9.6.1.16 Register 11Dh (address = 11Dh)
        17. 9.6.1.17 Register 122h (address = 122h)
        18. 9.6.1.18 Register 134h (address = 134h)
        19. 9.6.1.19 Register 139h (address = 139h)
        20. 9.6.1.20 Register 21Dh (address = 21Dh)
        21. 9.6.1.21 Register 222h (address = 222h)
        22. 9.6.1.22 Register 234h (address = 234h)
        23. 9.6.1.23 Register 239h (address = 239h)
        24. 9.6.1.24 Register 308h (address = 308h)
        25. 9.6.1.25 Register 41Dh (address = 41Dh)
        26. 9.6.1.26 Register 422h (address = 422h)
        27. 9.6.1.27 Register 434h (address = 434h)
        28. 9.6.1.28 Register 439h (address = 439h)
        29. 9.6.1.29 Register 51Dh (address = 51Dh)
        30. 9.6.1.30 Register 522h (address = 522h)
        31. 9.6.1.31 Register 534h (address = 534h)
        32. 9.6.1.32 Register 539h (address = 539h)
        33. 9.6.1.33 Register 608h (address = 608h)
        34. 9.6.1.34 Register 70Ah (address = 70Ah)
  10. 10Applications and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Applications
      1. 10.2.1 Driving Circuit Design: Low Input Frequencies
        1. 10.2.1.1 Design Requirements
        2. 10.2.1.2 Detailed Design Procedure
        3. 10.2.1.3 Application Curve
      2. 10.2.2 Driving Circuit Design: Input Frequencies Between 100 MHz to 230 MHz
        1. 10.2.2.1 Design Requirements
        2. 10.2.2.2 Detailed Design Procedure
        3. 10.2.2.3 Application Curve
      3. 10.2.3 Driving Circuit Design: Input Frequencies Greater than 230 MHz
        1. 10.2.3.1 Design Requirements
        2. 10.2.3.2 Detailed Design Procedure
        3. 10.2.3.3 Application Curve
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Related Links
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Community Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Revision History

Changes from A Revision (October 2015) to B Revision

  • Added description for availability of one-wire serial LVDS interface in Description section.Go
  • Changed Spectrum at 10 MHz figure to show conditions within curveGo
  • Changed description of AVDD, DVDD, and GND pins and added active high to description of PDN pin in Pin Functions tableGo
  • Deleted maximum from parameter description in Recommended Operating Conditions table Go
  • Changed Digital Outputs, RLOAD parameter description in Recommended Operating Conditions table Go
  • Changed conditions of all Electrical Characteristics and AC Performance tablesGo
  • Added minimum and maximum specifications to Analog Input, VOC(VCM) parameter in Electrical Characteristics: General tableGo
  • Changed description of Analog Input, Analog input bandwidth parameter in Electrical Characteristics: General tableGo
  • Deleted footnote 1 from Electrical Characteristics: General tableGo
  • Added DC Accuracy, EG parameter with its test conditions and footnote 3 to Electrical Characteristics: General tableGo
  • Deleted EG(REF) and EG(CHAN) from DC Accuracy in Electrical Characteristics: General table Go
  • Changed DC Accuracy, α(EGCHAN) to αEG and updated its parameter in Electrical Characteristics: General tableGo
  • Changed Channel-to-Channel Isolation, Crosstalk parameter in Electrical Characteristics: General table: changed test conditions, added footnote 2Go
  • Changed test conditions for IMD3 parameter in AC Performance: ADC3441 tableGo
  • Added INL and DNL rows to all AC Performance tablesGo
  • Changed Digital Inputs (SYSREFP, SYSREFM) subsection in Digital Characteristics table, added footnote 2Go
  • Changed specifications of Digital Outputs (LVDS Interface), VOCM parameter in Digital Characteristics tableGo
  • Changed rising to falling in description of SYSREF reference time parameter in Timing Requirements: General table Go
  • Changed Typical Characteristics sections: added dither on to all section condition statements, changed Non 23 to excluding HD2, HD3Go
  • Added INL and DNL plots in Typical Characteristics: ADC3441 sectionGo
  • Changed conditions of Figure 34, Figure 35Go
  • Added INL and DNL plots in Typical Characteristics: ADC3442 section Go
  • Changed conditions of Figure 67, Figure 68Go
  • Added INL and DNL plots in Typical Characteristics: ADC3443 section Go
  • Changed conditions of Figure 100, Figure 101Go
  • Added INL and DNL plots in Typical Characteristics: ADC3444 section. Go
  • Changed conditions of Figure 134 Go
  • Added Figure 141 to Timing Diagrams sectionGo
  • Added Using the SYSREF Input sectionGo
  • Changed the description about synchronization of the phase of the divided clock in each device to the common sampling clock in Using the SYSREF Input section. Go
  • Added ADC3441 Power-Up Requirements section, deleted the Register Initialization sectionGo
  • Added last sentence to Detailed Design Procedure section of first typical applicationGo
  • Added Chopper On to caption of Figure 198 Go
  • Added Chopper Off to caption of Figure 200 Go
  • Changed the caption of Figure 202 from FFT for 450-MHz Input Signal (Dither On) to FFT for 450-MHz Input Signal (Chopper Off, Dither On)Go

Changes from * Revision (July 2014) to A Revision

  • Released to productionGo