SLUSG51 October   2025 BQ25692-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1  Device Power-On-Reset
      2. 6.3.2  Battery Only Power Up State
      3. 6.3.3  Device HIZ State
      4. 6.3.4  Power Up REGN LDO
      5. 6.3.5  Default VINDPM Setting
      6. 6.3.6  Default Charge Profile Setting with CELL, ICHG and VCHG Pins
      7. 6.3.7  Buck-Boost Converter Operation
        1. 6.3.7.1 Pulse Frequency Modulation (PFM)
        2. 6.3.7.2 Switching Frequency and Dithering Feature
      8. 6.3.8  Forward (Sink) Operation
        1. 6.3.8.1 Power Path Management
          1. 6.3.8.1.1 Dynamic Power Management
            1. 6.3.8.1.1.1 ILIM_HIZ Pin
            2. 6.3.8.1.1.2 Input Current Optimizer (ICO)
        2. 6.3.8.2 Battery Charging Management
          1. 6.3.8.2.1 Battery Detection
          2. 6.3.8.2.2 Autonomous Charging Cycle
          3. 6.3.8.2.3 Battery Charging Profile
          4. 6.3.8.2.4 Charging Termination
          5. 6.3.8.2.5 Charging Safety Timer
          6. 6.3.8.2.6 CV Timer
          7. 6.3.8.2.7 Thermistor Qualification
            1. 6.3.8.2.7.1 JEITA Guideline Compliance in Charge Mode
            2. 6.3.8.2.7.2 Cold/Hot Temperature Window in Reverse Mode
        3. 6.3.8.3 Bypass Mode
      9. 6.3.9  Reverse (Source) Mode (USB On-The-Go)
        1. 6.3.9.1 Reverse (Source) Mode Operation
        2. 6.3.9.2 Backup Power Supply Mode
        3. 6.3.9.3 Reverse Bypass Mode
      10. 6.3.10 Status Outputs ( STAT, and INT)
        1. 6.3.10.1 Power Good Indicator (PG_STAT)
        2. 6.3.10.2 Charging Status Indicator (STAT Pin)
        3. 6.3.10.3 Interrupt to Host ( INT)
      11. 6.3.11 Serial Interface
        1. 6.3.11.1 Data Validity
        2. 6.3.11.2 START and STOP Conditions
        3. 6.3.11.3 Byte Format
        4. 6.3.11.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 6.3.11.5 Target Address and Data Direction Bit
        6. 6.3.11.6 Single Write and Read
        7. 6.3.11.7 Multi-Write and Multi-Read
    4. 6.4 Device Functional Modes
      1. 6.4.1 Host Mode and Default Mode
      2. 6.4.2 Register Bit Reset
    5. 6.5 Register Map
      1. 6.5.1 BQ25692Q1 Registers
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application Design Example
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
        1. 7.2.2.1 Inductor Selection
        2. 7.2.2.2 Capacitors
        3. 7.2.2.3 Buck Mode Input (VIN) Capacitor
        4. 7.2.2.4 Boost Mode Output (VOUT) Capacitor
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Device Support
      1. 8.1.1 Third-Party Products Disclaimer
    2. 8.2 Receiving Notification of Documentation Updates
    3. 8.3 Support Resources
    4. 8.4 Trademarks
    5. 8.5 Electrostatic Discharge Caution
    6. 8.6 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information
    1. 10.1 Package Option Addendum
    2. 10.2 Tape and Reel Information
    3. 10.3 Mechanical Data

Package Options

Mechanical Data (Package|Pins)
  • RBA|26
Thermal pad, mechanical data (Package|Pins)

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 

Copyright © 2024, Texas Instruments Incorporated