SCHS463 May   2025 CD3268A , CD3269A

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
  7. 6 Parameter Measurement Information
    1. 6.1 eN-MIC Microphone Integrated Noise Measurement
    2. 6.2 Current Measurements
    3. 6.3 MICPWR Output Voltage Measurement
    4. 6.4 Tone Mode Threshold Measurements
    5. 6.5 Impedance Measurements
    6. 6.6 Tone Mode Output Measurements
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Tone Mode Start-up Timing
      2. 7.3.2 Authentication
      3. 7.3.3 Shunt Regulator
      4. 7.3.4 Power-on-reset
    4. 7.4 Device Functional Modes
      1. 7.4.1 Button Mode
      2. 7.4.2 Tone Mode
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
      2. 9.1.2 Development Support
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Biases, Currents, & Thresholds
IMICBIAS-B Quiescent Current into MIC + VSHUNT Button Mode, VMICBIAS = 2.1V, (Figure 6-2) 3 6 μA
IMIC-T Quiescent Current into MIC Tone Mode, (Figure 6-3) 34 46 μA
IVSHUNT-T Quiescent Current into VSHUNT Tone Mode(1), (Figure 6-3) 60 80 μA
IMIC-TA Active Current into MIC Tone Mode, (Figure 6-4) 35 45 μA
IVSHUNT-TA Active Current into VSHUNT Tone Mode(1), (Figure 6-4) 104 123 μA
VTR Tone Mode Threshold Voltage - Rising MIC Rising (microphone enable), VMICPWR = 1.0V, (Figure 6-6 and Figure 6-7) 2.20 2.35 2.5 V
VTF Tone Mode Threshold Voltage - Falling MIC Falling (microphone enable), VMICPWR = 0.4V, (Figure 6-6 and Figure 6-7) 0.55 0.8 1 V
VMICPWR MICPWR Output Voltage IMICPWR = 120μA to 150μA, (Figure 6-5) 1.51 1.56 1.61 V
RSO Shunt Regulator Output Impedance Freq = 100Hz, (Figure 6-8) 5 18 25 Ω
Freq = 20kHz, (Figure 6-8) 12 21 35 Ω
Freq = 300kHz, (Figure 6-8) 300 458 650 Ω
Freq = 1MHz, (Figure 6-8) 2600 2830 3300 Ω
RONA Switch A, RDSON Tone Mode, IMICPWR = 1mA,
VMICBIAS = 2.56V, (Figure 6-9)
40 55 Ω
RONB Switch B, RDSON Button Mode, IREM = 1mA,
VMIC = 1.2V, (Figure 6-10)
22 30.5 Ω
Tone and Button Mode Parameters
en-mic100 MIC Integrated Noise 100Hz to 20kHz, (Figure 6-1) 1.5 2 μVRMS
en-mic1K MIC Integrated Noise 1kHz to 20kHz, (Figure 6-1) 0.39 1 μVRMS
fTONE1 Button 1 Frequency - CD3268 ACK Tone RREM = 6.81kΩ, (Figure 6-13) 109 130 159 kHz
fTONE2 Button 2 Frequency - CD3269 ACK Tone RREM = 9.42kΩ, (Figure 6-13) 138 165 200 kHz
fTONE3 Button 3 Frequency RREM = 12.99kΩ, (Figure 6-13) 167 201 242 kHz
fTONE4 Button 4 Frequency  RREM = 19.8 kΩ, (Figure 6-13) 196 237 284 kHz
fCAL Calibration Frequency (Figure 6-13) 225 271 325 kHz
fREL Button Release Frequency (Figure 6-13) 81 97 117 kHz
BR1 Button 1 Ratio fTONE1 / fCAL  0.470 0.488 0.500
BR2 Button 2 Ratio fTONE2 / fCAL  0.600 0.609 0.630
BR3 Button 3 Ratio fTONE3 / fCAL  0.730 0.740 0.758
BR4 Button 4 Ratio fTONE4 / fCAL  0.860 0.876 0.890
BRREL Button Release Ratio fREL / fCAL  0.340 0.360 0.380
RBT1 Button 1 Boundary 6.61 6.81 7.01 kΩ
RBT2 Button 2 Boundary 9.14 9.42 9.7 kΩ
RBT3 Button 3 Boundary 12.60 12.99 13.38 kΩ
RBT4 Button 4 Boundary 19.21 19.80 20.39 kΩ
VTA Tone Amplitude RTONE = 1MΩ, (Figure 6-11 and Figure 6-12) 350 550 720 mVp-p
RTONE = 100kΩ, (Figure 6-11 and Figure 6-12) 300 515 710 mVp-p
RTONE = 10kΩ, (Figure 6-11 and Figure 6-12) 200 390 620 mVp-p
RTONE = 1kΩ, (Figure 6-11 and Figure 6-12) 40 140 320 mVp-p
This current is pulled through RVSHUNT between MIC and VSHUNT and is the minimum current to keep VSHUNT regulated at 1.56V.  Excess current through RVSHUNT will be available to the load at MICPWR.  Excess current not used by the load at MICPWR will be internally shunted to GND.