SBOS052B September   2000  – January 2026 INA141

PRODUCTION DATA  

  1.   1
  2. 1Features
  3. 2Applications
  4. 3Description
  5. 4Pin Configuration and Functions
  6. 5Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6Application and Implementation
    1. 6.1 Application Information
      1. 6.1.1 Setting the Gain
      2. 6.1.2 Dynamic Performance
      3. 6.1.3 Noise Performance
      4. 6.1.4 Offset Trimming
      5. 6.1.5 Input Bias Current Return Path
      6. 6.1.6 Input Common-Mode Range
      7. 6.1.7 Low-Voltage Operation
      8. 6.1.8 Input Protection
  8. 7Device and Documentation Support
    1. 7.1 Device Nomenclature
    2. 7.2 Receiving Notification of Documentation Updates
    3. 7.3 Support Resources
    4. 7.4 Trademarks
    5. 7.5 Electrostatic Discharge Caution
    6. 7.6 Glossary
  9. 8Revision History
  10. 9Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Changes from Revision * (September 2000) to Revision A (August 2023)

  • Updated the numbering format for tables, figures, and cross-references throughout the documentGo
  • Added the Package Information table, and the Pin Configuration and Functions, Specifications, ESD Ratings, Recommended Operating Conditions, Thermal Information, Application and Implementation, Device and Documentation Support, and Mechanical, Packaging, and Orderable Information sectionsGo
  • Deleted PDIP package from data sheetGo
  • Added single supply specification to Absolute Maximum RatingsGo
  • Added note that output short-circuit (to ground) in Absolute Maximum Ratings means to short-circuit to VS / 2Go
  • Added "TA = –40°C to +85°C" test condition to Offset voltage vs temperature specification in the Electrical Characteristics and renamed to Offset voltage driftGo
  • Added test conditions "VREF = 0 V, VCM = VS / 2 and G = 10 below the titleGo
  • Deleted common-mode voltage typical values in the Electrical Characteristics and combined to one lineGo
  • Added "TA = –40°C to +85°C" test condition to Bias current vs temperature specification in the Electrical Characteristics and renamed to Input bias current drift for clarityGo
  • Added "TA = –40°C to +85°C" test condition to Offset current vs temperature specification in Electrical Characteristics and renamed to Input offset current drift for clarityGo
  • Added "TA = –40°C to +85°C" test condition for Gain error vs temperature in the Electrical Characteristics and renamed to Gain drift for clarityGo
  • Changed parameter names from "Voltage - Positive" and "Voltage - Negative" to "Output voltage" in the Electrical Characteristics Go
  • Added "Continuous to VS / 2" test condition short-circuit current specification in the Electrical Characteristics for clarityGo
  • Changed short-circuit current typical value from +6/-15 mA ±20 mAGo
  • Changed bandwidth typical value from 1 MHz to 610 kHz in the Electrical Characteristics Go
  • Changed slew rate typical value from 4 V/µs to 2 V/µs in the Electrical Characteristics Go
  • Deleted redundant voltage range, operating temperature range, and specification temperature range specifications from Electrical Characteristics Go
  • Changed Figure 6-2, Common-Mode Rejection vs Frequency Go
  • Changed Figure 6-8, Quiescent Current and Slew Rate vs Temperature Go
  • Changed Output Voltage Swing vs Output Current single plot to Figure 6-12, Positive Output Voltage Swing vs Output Current and Figure 6-12, Negative Output Voltage Swing vs Output Current Go
  • Changed Figure 6-18, Small-Signal Step Response Go
  • Changed Figure 6-19, Large-Signal Step Response Go
  • Changed Figure 6-20, 0.1Hz to 10Hz Input-Referred Voltage Noise Go
  • Changed G from 1 to 10V/V at the end of the Application Information sectionGo
  • Deleted reference to Input Bias Current vs Common-Mode Input Voltage plotGo