SNVSC22A October   2023  – March 2024 LM51772

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Description (continued)
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 Handling Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  Buck-Boost Control Scheme
        1. 8.3.1.1 Buck Mode
        2. 8.3.1.2 Boost Mode
        3. 8.3.1.3 Buck-Boost Mode
      2. 8.3.2  Power Save Mode
      3. 8.3.3  Programmable Conduction Mode PCM
      4. 8.3.4  Reference System
        1. 8.3.4.1 VIO LDO and nRST-PIN
      5. 8.3.5  Supply Voltage Selection – VMAX Switch and Selection Logic
      6. 8.3.6  Enable and Undervoltage Lockout
        1. 8.3.6.1 UVLO
        2. 8.3.6.2 VDET Comparator
      7. 8.3.7  Internal VCC Regulator
        1. 8.3.7.1 VCC1 Regulator
        2. 8.3.7.2 VCC2 Regulator
      8. 8.3.8  Error Amplifier and Control
        1. 8.3.8.1 Output Voltage Regulation
        2. 8.3.8.2 Internal Output Voltage Regulation
        3. 8.3.8.3 Dynamic Voltage Scaling
      9. 8.3.9  Short Circuit - Hiccup Protection
      10. 8.3.10 Current Monitor/Limiter
        1. 8.3.10.1 Overview
        2. 8.3.10.2 Output Current Limitation
        3. 8.3.10.3 Output Current Monitor
      11. 8.3.11 Oscillator Frequency Selection
      12. 8.3.12 Frequency Synchronization
      13. 8.3.13 Output Voltage Tracking
        1. 8.3.13.1 Analog Voltage Tracking
        2. 8.3.13.2 Digital Voltage Tracking
      14. 8.3.14 Slope Compensation
      15. 8.3.15 Configurable Soft Start
      16. 8.3.16 Drive Pin
      17. 8.3.17 Dual Random Spread Spectrum – DRSS
      18. 8.3.18 Gate Driver
      19. 8.3.19 Cable Drop Compensation (CDC)
      20. 8.3.20 CFG-pin and R2D Interface
      21. 8.3.21 Advanced Monitoring Features
        1. 8.3.21.1  Overview
        2. 8.3.21.2  BUSY
        3. 8.3.21.3  OFF
        4. 8.3.21.4  VOUT
        5. 8.3.21.5  IOUT
        6. 8.3.21.6  INPUT
        7. 8.3.21.7  TEMPERATURE
        8. 8.3.21.8  CML
        9. 8.3.21.9  OTHER
        10. 8.3.21.10 ILIM_OP
        11. 8.3.21.11 nFLT/nINT Pin Output
        12. 8.3.21.12 Status Byte
      22. 8.3.22 Protection Features
        1. 8.3.22.1  Thermal Shutdown (TSD)
        2. 8.3.22.2  Over Current Protection
        3. 8.3.22.3  Output Over Voltage Protection 1 (OVP1)
        4. 8.3.22.4  Output Over Voltage Protection 2 (OVP2)
        5. 8.3.22.5  Input Voltage Protection (IVP)
        6. 8.3.22.6  Input Voltage Regulation (IVR)
        7. 8.3.22.7  Power Good
        8. 8.3.22.8  Boot-Strap Under Voltage Protection
        9. 8.3.22.9  Boot-strap Over Voltage Clamp
        10. 8.3.22.10 CRC - CHECK
    4. 8.4 Device Functional Modes
      1. 8.4.1 Overview
      2. 8.4.2 Logic State Description
    5. 8.5 Programming
      1. 8.5.1 I2C Bus Operation
      2. 8.5.2 Clock Stretching
      3. 8.5.3 Data Transfer Formats
      4. 8.5.4 Single READ from a Defined Register Address
      5. 8.5.5 Sequential READ Starting from a Defined Register Address
      6. 8.5.6 Single WRITE to a Defined Register Address
      7. 8.5.7 Sequential WRITE Starting at a Defined Register Address
  10. 9 LM51772 Registers
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1  Custom Design with WEBENCH Tools
        2. 10.2.2.2  Frequency
        3. 10.2.2.3  Feedback Divider
        4. 10.2.2.4  Inductor and Current Sense Resistor Selection
        5. 10.2.2.5  Output Capacitor
        6. 10.2.2.6  Input Capacitor
        7. 10.2.2.7  Slope Compensation
        8. 10.2.2.8  UVLO Divider
        9. 10.2.2.9  Soft-Start Capacitor
        10. 10.2.2.10 MOSFETs QH1 and QL1
        11. 10.2.2.11 MOSFETs QH2 and QL2
        12. 10.2.2.12 Loop Compensation
        13. 10.2.2.13 External Component Selection
      3. 10.2.3 Application Curves
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
        1. 10.4.1.1 Power Stage Layout
        2. 10.4.1.2 Gate Driver Layout
        3. 10.4.1.3 Controller Layout
      2. 10.4.2 Layout Example
  12. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Support Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  13. 12Revision History
  14. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise specified)(1)
MIN MAX UNIT
Input BIAS to AGND –0.3 59 V
VIN, ISNSP, ISNSN to AGND –0.3 59
EN/UVLO, nRST  –0.3 59 (4)
V(VIN) + 5 (4)
ATRK/SS, DTRK, RT, SYNC, MODE, SDA, SCL, ADDR/SLOPE, CFG2, to AGND –0.3 5.8
FB, VIN-FB to AGND –0.3 5.8
CSA, CSB to SW1 –0.3 0.3
SW1, SW2  to AGND(DC)
 –0.5 59
SW1, SW2 to AGND ( ≤ 100ns duration) –2 59
SW1, SW2 to AGND(≤ 10ns duration) –3 59
SW1, SW2 to AGND(≤ 5ns duration) –4 59
HB1 to SW1, CSA, CSB –0.3 5.8
PGND to AGND –0.3 0.3
Output VCC1, VCC2 to AGND –0.3 5.5 V
VOUT to AGND –0.3 59
nFLT to AGND –0.3 5.8
COMP, ILIMCOMP, CDC to AGND(2) –0.3 5.8
LO1, LO2,  to PGND
 –0.3 V(VCC2)+0.3
HB1 to SW1, HB2 to SW2
 –0.3 5.5 (5)
–0.3 6
HO1 to SW1 –0.3 V(HB1)+0.3
HO2 to SW2 –0.3 V(HB2)+0.3
HO1, HO2, HB1, HB2  to AGND –0.3 65
Storage temperature, TSTG –55 150 °C
Operating junction temperature, TJ(3) –40 150
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) This pin has an internal max voltage clamp which can handle up to 1.6mA.
(3) High junction temperatures degrade operating lifetimes. Operating lifetime is de-rated for junction temperatures greater than 125°C.
(4) Both of the stated conditios need to be observed 
(5) Operating lifetime is de-rated for voltage bigger than the specified maximum