SNAS844 November   2024 LMK5B12212

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Diagrams
    7. 6.7 Typical Characteristics
  8. 7 Parameter Measurement Information
    1. 7.1 Differential Voltage Measurement Terminology
    2. 7.2 Output Clock Test Configurations
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
      1. 8.2.1 PLL Architecture Overview
      2. 8.2.2 DPLL
        1. 8.2.2.1 Independent DPLL Operation
        2. 8.2.2.2 APLL Cascaded With DPLL
      3. 8.2.3 APLL-Only Mode
    3. 8.3 Feature Description
      1. 8.3.1  Oscillator Input (XO)
      2. 8.3.2  Reference Inputs
      3. 8.3.3  Clock Input Interfacing and Termination
      4. 8.3.4  Reference Input Mux Selection
        1. 8.3.4.1 Automatic Input Selection
        2. 8.3.4.2 Manual Input Selection
      5. 8.3.5  Hitless Switching
        1. 8.3.5.1 Hitless Switching With Phase Cancellation
        2. 8.3.5.2 Hitless Switching With Phase Slew Control
      6. 8.3.6  Gapped Clock Support on Reference Inputs
      7. 8.3.7  Input Clock and PLL Monitoring, Status, and Interrupts
        1. 8.3.7.1 XO Input Monitoring
        2. 8.3.7.2 Reference Input Monitoring
          1. 8.3.7.2.1 Reference Validation Timer
          2. 8.3.7.2.2 Frequency Monitoring
          3. 8.3.7.2.3 Missing Pulse Monitor (Late Detect)
          4. 8.3.7.2.4 Runt Pulse Monitor (Early Detect)
          5. 8.3.7.2.5 Phase Valid Monitor for 1-PPS Inputs
        3. 8.3.7.3 PLL Lock Detectors
        4. 8.3.7.4 Tuning Word History
        5. 8.3.7.5 Status Outputs
        6. 8.3.7.6 Interrupt
      8. 8.3.8  PLL Relationships
        1. 8.3.8.1  PLL Frequency Relationships
          1. 8.3.8.1.1 APLL Phase Frequency Detector (PFD) and Charge Pump
          2. 8.3.8.1.2 APLL VCO Frequency
          3. 8.3.8.1.3 DPLL TDC Frequency
          4. 8.3.8.1.4 DPLL VCO Frequency
          5. 8.3.8.1.5 Clock Output Frequency
        2. 8.3.8.2  Analog PLLs (APLL1, APLL2)
        3. 8.3.8.3  APLL Reference Paths
          1. 8.3.8.3.1 APLL XO Doubler
          2. 8.3.8.3.2 APLL XO Reference (R) Divider
        4. 8.3.8.4  APLL Feedback Divider Paths
          1. 8.3.8.4.1 APLL N Divider With Sigma-Delta Modulator (SDM)
        5. 8.3.8.5  APLL Loop Filters (LF1, LF2)
        6. 8.3.8.6  APLL Voltage-Controlled Oscillators (VCO1, VCO2)
          1. 8.3.8.6.1 VCO Calibration
        7. 8.3.8.7  APLL VCO Clock Distribution Paths
        8. 8.3.8.8  DPLL Reference (R) Divider Paths
        9. 8.3.8.9  DPLL Time-to-Digital Converter (TDC)
        10. 8.3.8.10 DPLL Loop Filter (DLF)
        11. 8.3.8.11 DPLL Feedback (FB) Divider Path
      9. 8.3.9  Output Clock Distribution
      10. 8.3.10 Output Source Muxes
      11. 8.3.11 Output Channel Muxes
      12. 8.3.12 Output Dividers (OD)
      13. 8.3.13 Output Delay
      14. 8.3.14 Clock Outputs
        1. 8.3.14.1 Differential Output
        2. 8.3.14.2 LVCMOS Output
        3. 8.3.14.3 SYSREF/1PPS Output
      15. 8.3.15 Output Auto-Mute During LOL
      16. 8.3.16 Glitchless Output Clock Start-Up
      17. 8.3.17 Clock Output Interfacing and Termination
      18. 8.3.18 Output Synchronization (SYNC)
      19. 8.3.19 Zero-Delay Mode (ZDM)
      20. 8.3.20 DPLL Programmable Phase Delay
      21. 8.3.21 Time Elapsed Counter (TEC)
        1. 8.3.21.1 Configuring TEC Functionality
        2. 8.3.21.2 SPI as a Trigger Source
        3. 8.3.21.3 GPIO Pin as a TEC Trigger Source
          1. 8.3.21.3.1 An Example: Making a Time Elapsed Measurement Using TEC and GPIO1 as Trigger
        4. 8.3.21.4 Other TEC Behavior
    4. 8.4 Device Functional Modes
      1. 8.4.1 DPLL Operating States
        1. 8.4.1.1 Free-Run
        2. 8.4.1.2 Lock Acquisition
        3. 8.4.1.3 DPLL Locked
        4. 8.4.1.4 Holdover
      2. 8.4.2 Digitally-Controlled Oscillator (DCO) Frequency and Phase Adjustment
        1. 8.4.2.1 DPLL DCO Control
        2. 8.4.2.2 DPLL DCO Relative Adjustment Frequency Step Size
        3. 8.4.2.3 APLL DCO Frequency Step Size
      3. 8.4.3 APLL Frequency Control
      4. 8.4.4 Device Start-Up
        1. 8.4.4.1 Device Power-On Reset (POR)
        2. 8.4.4.2 PLL Start-Up Sequence
        3. 8.4.4.3 Start-Up Options for Register Configuration
        4. 8.4.4.4 GPIO1 and SCS_ADD Functionalities
        5. 8.4.4.5 ROM Page Selection
        6. 8.4.4.6 EEPROM Overlay
      5. 8.4.5 Programming
        1. 8.4.5.1 Memory Overview
        2. 8.4.5.2 Interface and Control
          1. 8.4.5.2.1 Programming Through TICS Pro
          2. 8.4.5.2.2 SPI Serial Interface
          3. 8.4.5.2.3 I2C Serial Interface
        3. 8.4.5.3 General Register Programming Sequence
        4. 8.4.5.4 Steps to Program the EEPROM
          1. 8.4.5.4.1 Overview of the SRAM Programming Methods
          2. 8.4.5.4.2 EEPROM Programming With the Register Commit Method
          3. 8.4.5.4.3 EEPROM Programming With the Direct Writes Method or Mixed Method
          4. 8.4.5.4.4 Five MSBs of the I2C Address and the EEPROM Revision Number
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Device Start-Up Sequence
      2. 9.1.2 Power Down (PD#) Pin
      3. 9.1.3 Strap Pins for Start-Up
      4. 9.1.4 Pin States
      5. 9.1.5 ROM and EEPROM
      6. 9.1.6 Power Rail Sequencing, Power Supply Ramp Rate, and Mixing Supply Domains
        1. 9.1.6.1 Power-On Reset (POR) Circuit
        2. 9.1.6.2 Power Up From a Single-Supply Rail
        3. 9.1.6.3 Power Up From Split-Supply Rails
        4. 9.1.6.4 Non-Monotonic or Slow Power-Up Supply Ramp
      7. 9.1.7 Slow or Delayed XO Start-Up
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
      3. 9.2.3 Application Curves
    3. 9.3 Best Design Practices
    4. 9.4 Power Supply Recommendations
      1. 9.4.1 Power Supply Bypassing
    5. 9.5 Layout
      1. 9.5.1 Layout Guidelines
      2. 9.5.2 Layout Example
      3. 9.5.3 Thermal Reliability
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Glossary
    6. 10.6 Electrostatic Discharge Caution
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

6.7 Typical Characteristics

LMK5B12212 312.5MHz HSDS Output From APLL1 BAW
Jitter = 41fs RMS (12kHz to 20MHz)
fAPLL1 = 2500MHz (APLL1 post-divider = 8)
Figure 6-8 312.5MHz HSDS Output From APLL1 BAW
LMK5B12212 125MHz HSDS Output From APLL1 BAW
Jitter = 65fs RMS (12kHz to 20MHz)
fAPLL1 = 2500MHz (APLL1 post-div = 5, Channel-div = 4)
Figure 6-10 125MHz HSDS Output From APLL1 BAW
LMK5B12212 322.265625MHz HSDS Output From APLL2
Jitter = 98fs RMS (12kHz to 20MHz)
fAPLL2 = 5800.78125MHz
Figure 6-12 322.265625MHz HSDS Output From APLL2
LMK5B12212 212.5MHz HSDS Output From APLL2
Jitter = 103fs RMS (12kHz to 20MHz)
fAPLL2 = 5950MHz
Figure 6-14 212.5MHz HSDS Output From APLL2
LMK5B12212 155.52MHz HSDS Output From APLL2
Jitter = 101fs RMS (12kHz to 20MHz)
fAPLL2 = 5598.72MHz
Figure 6-16 155.52MHz HSDS Output From APLL2
LMK5B12212 122.88MHz HSDS Output From APLL2
Jitter = 108fs RMS (12kHz to 20MHz)
fAPLL2 = 5898.24MHz
Figure 6-18 122.88MHz HSDS Output From APLL2
LMK5B12212 156.25MHz HSDS Output From APLL1 BAW
Jitter = 47fs RMS (12kHz to 20MHz)
fAPLL1 = 2500MHz (APLL1 post-div = 8, div2 enabled)
Figure 6-9 156.25MHz HSDS Output From APLL1 BAW
LMK5B12212 100MHz HSDS Output From APLL1 BAW
Jitter = 85fs RMS (12kHz to 20MHz)
fAPLL1 = 2500MHz (APLL1 post-div = 5, Channel-div = 5)
Figure 6-11 100MHz HSDS Output From APLL1 BAW
LMK5B12212 245.76MHz HSDS Output From APLL2
Jitter = 102fs RMS (12kHz to 20MHz)
fAPLL2 = 5898.24MHz
Figure 6-13 245.76MHz HSDS Output From APLL2
LMK5B12212 161.1328125MHz HSDS Output From APLL2
Jitter = 101fs RMS (12kHz to 20MHz)
fAPLL2 = 5800.78125MHz
Figure 6-15 161.1328125MHz HSDS Output From APLL2
LMK5B12212 153.6MHz HSDS Output From APLL2
Jitter = 100fs RMS (12kHz to 20MHz)
fAPLL2 = 5836.8MHz
Figure 6-17 153.6MHz HSDS Output From APLL2

LMK5B12212 SYSREF/1PPS Delay Linearity vs. Analog Delay Code 2
Figure 6-19 SYSREF/1PPS Delay Linearity vs. Analog Delay Code 2

LMK5B12212 SYSREF/1PPS Delay Linearity vs. Analog Delay Code 4
Figure 6-21 SYSREF/1PPS Delay Linearity vs. Analog Delay Code 4

LMK5B12212 SYSREF/1PPS Delay Linearity vs. Analog Delay Code 3
Figure 6-20 SYSREF/1PPS Delay Linearity vs. Analog Delay Code 3

LMK5B12212 SYSREF/1PPS Delay Linearity vs. Analog Delay Code 5
Figure 6-22 SYSREF/1PPS Delay Linearity vs. Analog Delay Code 5