SLLSF58B July   2020  – May 2022 TLIN1027-Q1

PRODUCTION DATA  

  1. Features
  2. Applications
  3. Description
  4. Revision History
  5. Pin Configuration and Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 ESD Ratings - IEC
    4. 6.4 Thermal Information
    5. 6.5 Recommended Operating Conditions
    6. 6.6 Electrical Characteristics
    7. 6.7 Switching Characteristics
    8. 6.8 Timing Requirements
    9. 6.9 Typical Characteristics
  7. Parameter Measurement Information
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  LIN (Local Interconnect Network) Bus
        1. 8.3.1.1 LIN Transmitter Characteristics
        2. 8.3.1.2 LIN Receiver Characteristics
          1. 8.3.1.2.1 Termination
      2. 8.3.2  TXD (Transmit Input and Output)
      3. 8.3.3  RXD (Receive Output)
      4. 8.3.4  VSUP (Supply Voltage)
      5. 8.3.5  GND (Ground)
      6. 8.3.6  EN (Enable Input)
      7. 8.3.7  Protection Features
      8. 8.3.8  Bus Stuck Dominant System Fault: False Wake-Up Lockout
      9. 8.3.9  Thermal Shutdown
      10. 8.3.10 Under Voltage on VSUP
      11. 8.3.11 Unpowered Device and LIN Bus
    4. 8.4 Device Functional Modes
      1. 8.4.1 Normal Mode
      2. 8.4.2 Sleep Mode
      3. 8.4.3 Standby Mode
      4. 8.4.4 Wake-Up Events
        1. 8.4.4.1 Wake-Up Request (RXD)
        2. 8.4.4.2 Mode Transitions
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedures
        1. 9.2.2.1 Normal Mode Application Note
        2. 9.2.2.2 Standby Mode Application Note
      3. 9.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Documentation Support
      1. 12.1.1 Related Documentation
    2. 12.2 Receiving Notification of Documentation Updates
    3. 12.3 Support Resources
    4. 12.4 Trademarks
    5. 12.5 Electrostatic Discharge Caution
    6. 12.6 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Electrical Characteristics

parameters valid across -40℃ ≤ TA ≤ 125℃ (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Power Supply
VSUP Operational supply voltage (ISO/DIS 17987 Param 10) Device is operational beyond the LIN defined nominal supply voltage range. See Figure 7-1 and Figure 7-2 4 36 V
VSUP Nominal supply voltage (ISO/DIS 17987 Param 10) Normal and Standby Modes: ramp VSUP while LIN signal is a 10 kHz square wave with 50 % duty cycle and 18V swing. See Figure 7-1 and Figure 7-2 4   36 V
Sleep Mode 4   36 V
UVSUP Under voltage VSUP threshold Min is falling edge and Max is rising edge 2.9 3.85 V
UVHYS Delta hysteresis voltage for VSUP under voltage threshold 0.2 V
ISUP Supply current Normal Mode: EN = high, bus dominant: total bus load where RLIN > 500 Ω and CLIN < 10 nF (See Figure 7-7) 5 mA
Standby Mode: EN = low, bus dominant: total bus load where RLIN > 500 Ω and CLIN < 10 nF (See Figure 7-7) 1 2.1 mA
ISUP Supply current Normal Mode: EN = high, bus recessive (LIN = VSUP)   300 650 µA
Standby Mode: EN = low, bus recessive (LIN = VSUP)   10 30 µA
Sleep Mode: 4.0 V < VSUP ≤ 14 V, LIN = VSUP, EN = 0 V, TXD and RXD floating   8 12 µA
Sleep Mode: 14 V < VSUP ≤ 36 V, LIN = VSUP, EN = 0 V, TXD and RXD floating     20 µA
TSD Thermal shutdown 165
TSD(HYS) Thermal shutdown hysteresis 15
RXD OUTPUT PIN (OPEN DRAIN)
VOL Output low voltage RPU = 2.4 kΩ 0.6 V
IOL Low level output current, open drain LIN = 0 V, RXD = 0.4 V 1.5 mA
IILG Leakage current, high-level LIN = VSUP, RXD = 5 V –5 0 5 µA
TXD INPUT PIN
VIL Low level input voltage –0.3 0.8 V
VIH High level input voltage 2 5.5 V
IILG Low level input leakage current TXD = low –5 0 5 µA
RTXD Internal pull-down resistor value 125 350 800
LIN PIN
VOH HIGH level output voltage LIN recessive, TXD = high, IO = 0 mA, VSUP = 7 V to 36  V(1) 0.85 VSUP
LIN recessive, TXD = high, IO = 0 mA, VSUP = 4 V ≤ VSUP < 7 V(1) 3 V
VOL LOW level output voltage LIN dominant, TXD = low, VSUP = 7 V to 36  V(1) 0.2 VSUP
LIN dominant, TXD = low, VSUP = 4 V ≤ VSUP < 7 V(1) 1.2 V
VSUP_NON_OP VSUP where impact of recessive LIN bus < 5% (ISO/DIS 17987 Param 11) TXD & RXD open LIN = 4 V to 45 V –0.3 45 V
IBUS_LIM Limiting current (ISO/DIS 17987 Param 12) TXD = 0 V, VLIN = 18 V, RMEAS = 440 Ω, VSUP = 18 V, VBUSdom < 4.518 V See Figure 7-6 40 90 200 mA
IBUS_PAS_dom Receiver leakage current, dominant (ISO/DIS 17987 Param 13) LIN = 0 V, VSUP = 12 V Driver off/recessive Figure 7-7 –1 mA
IBUS_PAS_rec1 Receiver leakage current, recessive (ISO/DIS 17987 Param 14) LIN > VSUP, 4 V ≤ VSUP ≤ 36 V Driver off; Figure 7-8 20 µA
IBUS_PAS_rec2 Receiver leakage current, recessive (ISO/DIS 17987 Param 14) LIN = VSUP, Driver off; Figure 7-8 –5 5 µA
IBUS_NO_GND Leakage current, loss of ground (ISO/DIS 17987 Param 15) GND = VSUP, VSUP = 18 V, LIN = 0 V; Figure 7-9 –1 1 mA
IBUS_NO_BAT Leakage current, loss of supply (ISO/DIS 17987 Param 16) LIN = 18 V, VSUP = GND; Figure 7-10 5 µA
VBUSdom Low level input voltage (ISO/DIS 17987 Param 17) LIN dominant (including LIN dominant for wake up) See Figure 7-4Figure 7-3 0.4 VSUP
VBUSrec High level input voltage (ISO/DIS 17987 Param 18) LIN recessive See Figure 7-4Figure 7-3 0.6 VSUP
VBUS_CNT Receiver center threshold (ISO/DIS 17987 Param 19) VBUS_CNT = (VIL + VIH)/2 See Figure 7-4Figure 7-3 0.475 0.5 0.525 VSUP
VHYS Hysteresis voltage (ISO/DIS 17987 Param 20) VHYS = (VIL - VIH) See Figure 7-4Figure 7-3 0.175 VSUP
VSERIAL_DIODE Serial diode LIN term pull-up path  By design and characterization 0.4 0.7 1 V
RPU-LIN Internal pull-up resistor to VSUP Normal and standby modes 20 45 60
IRSLEEP Pull-up current source to VSUP Sleep mode, VSUP = 14 V, LIN = GND –2 –20 µA
CLINPIN Capacitance of the LIN pin VSUP = 14 V 25 pF
EN INPUT PIN
VIL Low level input voltage –0.3 0.8 V
VIH High level input voltage 2 5.5 V
VIT Hysteresis voltage By design and characterization 50 500 mV
IILG Low level input current EN = low –5 0 5 µA
REN Internal pull-down resistor 125 205 800
LIN driver bus load conditions (CLIN, RLIN): No external load