SLVSIO8 September   2026 TPS638221

PRODMIX  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Control Scheme
        1. 7.3.1.1 Buck Operation
        2. 7.3.1.2 Boost Operation
        3. 7.3.1.3 Buck-Boost Operation
      2. 7.3.2 Operation Mode
        1. 7.3.2.1 PFM Operation
        2. 7.3.2.2 Forced-PWM Operation (FPWM)
        3. 7.3.2.3 Ultra-sonic Mode Operation
      3. 7.3.3 Undervoltage Lockout (UVLO)
      4. 7.3.4 Enable and Soft Start
      5. 7.3.5 Protection Functions
        1. 7.3.5.1 Input Voltage Protection (IVP)
        2. 7.3.5.2 Output Voltage Protection (OVP)
        3. 7.3.5.3 Current Limit Mode and Overcurrent Protection
        4. 7.3.5.4 Output Short Circuit Protection (Hiccup)
        5. 7.3.5.5 Thermal Shutdown
      6. 7.3.6 Power Good
      7. 7.3.7 Load Disconnect
      8. 7.3.8 Output Discharge
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Applications
      1. 8.2.1 3.3V Output Power Supply
        1. 8.2.1.1 Design Requirements
        2. 8.2.1.2 Detailed Design Procedure
          1. 8.2.1.2.1 Inductor Selection
          2. 8.2.1.2.2 Output Capacitor Selection
          3. 8.2.1.2.3 Input Capacitor Selection
          4. 8.2.1.2.4 Setting the Output Voltage
        3. 8.2.1.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Third-Party Products Disclaimer
      2. 9.1.2 Third-Party Products Disclaimer
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Export Control Notice
    8. 9.8 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1.     67

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • |
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.3.5.1 Input Voltage Protection (IVP)

Under certain operating conditions, current can flow from the output of the device to the input. For example, this kind of current flow from the output to the input can occur during dynamic voltage scaling when the output ramps down to a lower voltage and the VOUT pin sinks current from the output capacitor. Under such conditions, if the voltage source supplying the device cannot sink current, the voltage on the VIN pin can rise uncontrollably.

To make sure the input voltage stays within the permitted range, the device stops switching if the voltage on the VIN pin is greater than 5.75V. The device automatically starts to switch again when the voltage on the VIN pin is less than 5.65V.