JAJSRL6 November   2023 AFE432A3W , AFE532A3W

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics: Voltage Output
    6. 5.6  Electrical Characteristics: Current Output
    7. 5.7  Electrical Characteristics: Comparator Mode
    8. 5.8  Electrical Characteristics: ADC Input
    9. 5.9  Electrical Characteristics: General
    10. 5.10 Timing Requirements: I2C Standard Mode
    11. 5.11 Timing Requirements: I2C Fast Mode
    12. 5.12 Timing Requirements: I2C Fast-Mode Plus
    13. 5.13 Timing Requirements: SPI Write Operation
    14. 5.14 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 0)
    15. 5.15 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 1)
    16. 5.16 Timing Requirements: GPIO
    17. 5.17 Timing Diagrams
    18. 5.18 Typical Characteristics: Voltage Output
    19. 5.19 Typical Characteristics: Current Output
    20. 5.20 Typical Characteristics: Comparator
    21. 5.21 Typical Characteristics: ADC
    22. 5.22 Typical Characteristics: General
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Smart Analog Front End (AFE) Architecture
      2. 6.3.2 Digital Input/Output
      3. 6.3.3 Nonvolatile Memory (NVM)
    4. 6.4 Device Functional Modes
      1. 6.4.1 Voltage-Output Mode
        1. 6.4.1.1 Voltage Reference and DAC Transfer Function
          1. 6.4.1.1.1 Internal Reference
          2. 6.4.1.1.2 Power-Supply as Reference
      2. 6.4.2 Current-Output Mode
      3. 6.4.3 Comparator Mode
        1. 6.4.3.1 Programmable Hysteresis Comparator
        2. 6.4.3.2 Programmable Window Comparator
      4. 6.4.4 Analog-to-Digital Converter (ADC) Mode
      5. 6.4.5 Fault-Dump Mode
      6. 6.4.6 Application-Specific Modes
        1. 6.4.6.1 Voltage Margining and Scaling
          1. 6.4.6.1.1 High-Impedance Output and PROTECT Input
          2. 6.4.6.1.2 Programmable Slew-Rate Control
        2. 6.4.6.2 Function Generation
          1. 6.4.6.2.1 Triangular Waveform Generation
          2. 6.4.6.2.2 Sawtooth Waveform Generation
          3. 6.4.6.2.3 Sine Waveform Generation
      7. 6.4.7 Device Reset and Fault Management
        1. 6.4.7.1 Power-On Reset (POR)
        2. 6.4.7.2 External Reset
        3. 6.4.7.3 Register-Map Lock
        4. 6.4.7.4 NVM Cyclic Redundancy Check (CRC)
          1. 6.4.7.4.1 NVM-CRC-FAIL-USER Bit
          2. 6.4.7.4.2 NVM-CRC-FAIL-INT Bit
      8. 6.4.8 General-Purpose Input/Output (GPIO) Modes
    5. 6.5 Programming
      1. 6.5.1 SPI Programming Mode
      2. 6.5.2 I2C Programming Mode
        1. 6.5.2.1 F/S Mode Protocol
        2. 6.5.2.2 I2C Update Sequence
          1. 6.5.2.2.1 Address Byte
          2. 6.5.2.2.2 Command Byte
        3. 6.5.2.3 I2C Read Sequence
  8. 7 Register Map
    1. 7.1  NOP Register (address = 00h) [reset = 0000h]
    2. 7.2  DAC-0-MARGIN-HIGH Register (address = 0Dh) [reset = 0000h]
    3. 7.3  DAC-1-MARGIN-HIGH Register (address = 13h) [reset = 0000h]
    4. 7.4  DAC-2-MARGIN-HIGH Register (address = 01h) [reset = 0000h]
    5. 7.5  DAC-0-MARGIN-LOW Register (address = 0Eh) [reset = 0000h]
    6. 7.6  DAC-1-MARGIN-LOW Register (address = 14h) [reset = 0000h]
    7. 7.7  DAC-2-MARGIN-LOW Register (address = 02h) [reset = 0000h]
    8. 7.8  DAC-0-GAIN-CONFIG Register (address = 0Fh) [reset = 0000h]
    9. 7.9  DAC-1-GAIN-CMP-CONFIG Register (address = 15h) [reset = 0000h]
    10. 7.10 DAC-2-GAIN-CONFIG Register (address = 03h) [reset = 0000h]
    11. 7.11 DAC-1-CMP-MODE-CONFIG Register (address = 17h) [reset = 0000h]
    12. 7.12 DAC-0-FUNC-CONFIG Register (address = 12h) [reset = 0000h]
    13. 7.13 DAC-1-FUNC-CONFIG Register (address = 18h) [reset = 0000h]
    14. 7.14 DAC-2-FUNC-CONFIG Register (address = 06h) [reset = 0000h]
    15. 7.15 DAC-0-DATA Register (address = 1Bh) [reset = 0000h]
    16. 7.16 DAC-1-DATA Register (address = 1Ch) [reset = 0000h]
    17. 7.17 DAC-2-DATA Register (address = 19h) [reset = 0000h]
    18. 7.18 ADC-CONFIG-TRIG Register (address = 1Dh) [reset = 0000h]
    19. 7.19 ADC-DATA Register (address = 1Eh) [reset = 0001h]
    20. 7.20 COMMON-CONFIG Register (address = 1Fh) [reset = 0FFFh]
    21. 7.21 COMMON-TRIGGER Register (address = 20h) [reset = 0000h]
    22. 7.22 COMMON-DAC-TRIG Register (address = 21h) [reset = 0000h]
    23. 7.23 GENERAL-STATUS Register (address = 22h) [reset = 20h, DEVICE-ID, VERSION-ID]
    24. 7.24 CMP-STATUS Register (address = 23h) [reset = 000Ch]
    25. 7.25 GPIO-CONFIG Register (address = 24h) [reset = 0000h]
    26. 7.26 DEVICE-MODE-CONFIG Register (address = 25h) [reset = 0000h]
    27. 7.27 INTERFACE-CONFIG Register (address = 26h) [reset = 0000h]
    28. 7.28 SRAM-CONFIG Register (address = 2Bh) [reset = 0000h]
    29. 7.29 SRAM-DATA Register (address = 2Ch) [reset = 0000h]
    30. 7.30 BRDCAST-DATA Register (address = 50h) [reset = 0000h]
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 ドキュメントの更新通知を受け取る方法
    3. 9.3 サポート・リソース
    4. 9.4 Trademarks
    5. 9.5 静電気放電に関する注意事項
    6. 9.6 用語集
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

6.5.1 SPI Programming Mode

An SPI access cycle for AFEx32A3W is initiated by asserting the SYNC pin low. The serial clock, SCLK, can be a continuous or gated clock. SDI data are clocked on SCLK falling edges. The SPI frame for AFEx32A3W is 24 bits long. Therefore, the SYNC pin must stay low for at least 24 SCLK falling edges. The access cycle ends when the SYNC pin is deasserted high. If the access cycle contains less than the minimum clock edges, the communication is ignored. By default, the SDO function is not enabled (three-wire SPI). In the three-wire SPI mode, if the access cycle contains more than the minimum clock edges, only the first 24 bits are used by the device. When SYNC is high, the SCLK and SDI signals are blocked, and SDO becomes Hi-Z to allow data readback from other devices connected on the bus.

Table 6-11 and Figure 6-15 describe the format for the 24-bit SPI access cycle. The first byte input to SDI is the instruction cycle. The instruction cycle identifies the request as a read or write command and the 7-bit address that is to be accessed. The last 16 bits in the cycle form the data cycle.

Table 6-11 SPI Read/Write Access Cycle
BITFIELDDESCRIPTION
23R/WIdentifies the communication as a read or write command to the address register: R/W = 0 sets a write operation. R/W = 1 sets a read operation
22-16A[6:0]Register address: specifies the register to be accessed during the read or write operation
15-0DI[15:0]Data cycle bits: If a write command, the data cycle bits are the values to be written to the register with address A[6:0]. If a read command, the data cycle bits are don't care values.
GUID-46728286-8753-479B-8075-A6FE4683F7AB-low.svg Figure 6-15 SPI Write Cycle

Read operations require that the SDO function is first enabled by setting the SDO-EN bit in the INTERFACE-CONFIG register. This configuration is called four-wire SPI. A read operation is initiated by issuing a read command access cycle. After the read command, a second access cycle must be issued to get the requested data. Table 6-12 and Figure 6-16 show the output data format. Data are clocked out on the SDO pin either on the falling edge or rising edge of SCLK according to the FSDO bit (see also Figure 5-3).

Table 6-12 SDO Output Access Cycle
BITFIELDDESCRIPTION
23R/WEcho R/W from previous access cycle
22-16A[6:0]Echo register address from previous access cycle
15-0DI[15:0]Readback data requested on previous access cycle
GUID-D749EAD7-9F83-4DFB-8269-F3A5B33141EB-low.svg Figure 6-16 SPI Read Cycle

The daisy-chain operation is also enabled with the SDO pin. Figure 6-17 shows that in daisy-chain mode, multiple devices are connected in a chain with the SDO pin of one device is connected to SDI pin of the following device. The SPI host drives the SDI pin of the first device in the chain. The SDO pin of the last device in the chain is connected to the POCI pin of the SPI host. In four-wire SPI mode, if the access cycle contains multiples of 24 clock edges, only the last 24 bits are used by the device first device in the chain. If the access cycle contains clock edges that are not in multiples of 24, the SPI packet is ignored by the device. Figure 6-18 describes the packet format for the daisy-chain write cycle.

GUID-BEA8125F-D2AB-4A0C-8BEA-A9A57065FE86-low.svgFigure 6-17 SPI Daisy-Chain Connection
GUID-C7075615-F23B-4C91-AE0A-39F4AD844CE7-low.svgFigure 6-18 SPI Daisy-Chain Write Cycle