JAJSFQ9C june   2018  – may 2023 BQ25713 , BQ25713B

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 概要 (続き)
  7. 6 Device Comparison Table
  8. 7 Pin Configuration and Functions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Power-Up from Battery Without DC Source
      2. 9.3.2  Vmin Active Protection (VAP) when Battery only Mode
      3. 9.3.3  Power-Up From DC Source
        1. 9.3.3.1 CHRG_OK Indicator
        2. 9.3.3.2 Input Voltage and Current Limit Setup
        3. 9.3.3.3 Battery Cell Configuration
        4. 9.3.3.4 Device Hi-Z State
      4. 9.3.4  USB On-The-Go (OTG)
      5. 9.3.5  Converter Operation
        1. 9.3.5.1 Inductance Detection Through IADPT Pin
        2. 9.3.5.2 Continuous Conduction Mode (CCM)
        3. 9.3.5.3 Pulse Frequency Modulation (PFM)
      6. 9.3.6  Current and Power Monitor
        1. 9.3.6.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 9.3.6.2 High-Accuracy Power Sense Amplifier (PSYS)
      7. 9.3.7  Input Source Dynamic Power Manage
      8. 9.3.8  Two-Level Adapter Current Limit (Peak Power Mode)
      9. 9.3.9  Processor Hot Indication
        1. 9.3.9.1 PROCHOT During Low Power Mode
        2. 9.3.9.2 PROCHOT Status
      10. 9.3.10 Device Protection
        1. 9.3.10.1 Watchdog Timer
        2. 9.3.10.2 Input Overvoltage Protection (ACOV)
        3. 9.3.10.3 Input Overcurrent Protection (ACOC)
        4. 9.3.10.4 System Overvoltage Protection (SYSOVP)
        5. 9.3.10.5 Battery Overvoltage Protection (BATOVP)
        6. 9.3.10.6 Battery Short
        7. 9.3.10.7 System Short Hiccup Mode
        8. 9.3.10.8 Thermal Shutdown (TSHUT)
    4. 9.4 Device Functional Modes
      1. 9.4.1 Forward Mode
        1. 9.4.1.1 System Voltage Regulation with Narrow VDC Architecture
        2. 9.4.1.2 Battery Charging
      2. 9.4.2 USB On-The-Go
      3. 9.4.3 Pass Through Mode (PTM)
    5. 9.5 Programming
      1. 9.5.1 I2C Serial Interface
        1. 9.5.1.1 Data Validity
        2. 9.5.1.2 START and STOP Conditions
        3. 9.5.1.3 Byte Format
        4. 9.5.1.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 9.5.1.5 Slave Address and Data Direction Bit
        6. 9.5.1.6 Single Read and Write
        7. 9.5.1.7 Multi-Read and Multi-Write
        8. 9.5.1.8 Write 2-Byte I2C Commands
    6. 9.6 Register Map
      1. 9.6.1  Setting Charge and PROCHOT Options
        1. 9.6.1.1 ChargeOption0 Register (I2C address = 01/00h) [reset = E70Eh]
        2. 9.6.1.2 ChargeOption1 Register (I2C address = 31/30h) [reset = 0211h]
        3. 9.6.1.3 ChargeOption2 Register (I2C address = 33/32h) [reset = 02B7h]
        4. 9.6.1.4 ChargeOption3 Register (I2C address = 35/34h) [reset = 0030h]
        5. 9.6.1.5 ProchotOption0 Register (I2C address = 37/36h) [reset = 4A65h]
        6. 9.6.1.6 ProchotOption1 Register (I2C address = 39/38h) [reset = 81A0h]
        7. 9.6.1.7 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]
      2. 9.6.2  Charge and PROCHOT Status
        1. 9.6.2.1 ChargerStatus Register (I2C address = 21/20h) [reset = 0000h]
        2. 9.6.2.2 ProchotStatus Register (I2C address = 23/22h) [reset = A800h]
      3. 9.6.3  ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]
        1. 9.6.3.1 Battery Precharge Current Clamp
      4. 9.6.4  MaxChargeVoltage Register (I2C address = 05/04h) [reset value based on CELL_BATPRESZ pin setting]
      5. 9.6.5  MinSystemVoltage Register (I2C address = 0D/0Ch) [reset value based on CELL_BATPRESZ pin setting]
        1. 9.6.5.1 System Voltage Regulation
      6. 9.6.6  Input Current and Input Voltage Registers for Dynamic Power Management
        1. 9.6.6.1 Input Current Registers
          1. 9.6.6.1.1 IIN_HOST Register With 10-mΩ Sense Resistor (I2C address = 0F/0Eh) [reset = 4100h]
          2. 9.6.6.1.2 IIN_DPM Register With 10-mΩ Sense Resistor (I2C address = 25/24h) [reset = 4100h]
          3. 9.6.6.1.3 InputVoltage Register (I2C address = 0B/0Ah) [reset = VBUS-1.28V]
      7. 9.6.7  OTGVoltage Register (I2C address = 07/06h) [reset = 0000h]
      8. 9.6.8  OTGCurrent Register (I2C address = 09/08h) [reset = 0000h]
      9. 9.6.9  ADCVBUS/PSYS Register (I2C address = 27/26h)
      10. 9.6.10 ADCIBAT Register (I2C address = 29/28h)
      11. 9.6.11 ADCIINCMPIN Register (I2C address = 2B/2Ah)
      12. 9.6.12 ADCVSYSVBAT Register (I2C address = 2D/2Ch)
      13. 9.6.13 ID Registers
        1. 9.6.13.1 ManufactureID Register (I2C address = 2Eh) [reset = 0040h]
        2. 9.6.13.2 Device ID (DeviceAddress) Register (I2C address = 2Fh) [reset = 0h]
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 ACP-ACN Input Filter
        2. 10.2.2.2 Inductor Selection
        3. 10.2.2.3 Input Capacitor
        4. 10.2.2.4 Output Capacitor
        5. 10.2.2.5 Power MOSFETs Selection
      3. 10.2.3 Application Curves
  12. 11Power Supply Recommendations
  13. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
      1. 12.2.1 Layout Example Reference Top View
      2. 12.2.2 Inner Layer Layout and Routing Example
  14. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 サード・パーティ製品に関する免責事項
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 ドキュメントの更新通知を受け取る方法
    4. 13.4 サポート・リソース
    5. 13.5 Trademarks
    6. 13.6 静電気放電に関する注意事項
    7. 13.7 用語集
  15. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.6.7 OTGVoltage Register (I2C address = 07/06h) [reset = 0000h]

To set the OTG output voltage limit, write to REG0x07/06() using the data format listed in Figure 9-27, Table 9-35, and Table 9-36.

The DAC is clamped in digital core at minimal 3V and maximum 20.8V. Any register writing lower than the minimal or higher than the maximum will be ignored. When REG0x34[2] = 1, there is no DAC offset. When REG0x34[2] = 0 the DAC is offset by 1.28V

Figure 9-27 OTGVoltage Register (I2C address = 07/06h) [reset = 0000h]
76543210
ReservedOTG Voltage, bit 11OTG Voltage, bit 10OTG Voltage, bit 9OTG Voltage, bit 8OTG Voltage, bit 7OTG Voltage, bit 6
R/WR/WR/WR/WR/WR/WR/W
76543210
OTG Voltage, bit 5OTG Voltage, bit 4OTG Voltage, bit 3OTG Voltage, bit 2OTG Voltage, bit 1OTG Voltage, bit 0Reserved
R/WR/WR/WR/WR/WR/WR/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 9-35 OTGVoltage Register (I2C address = 07h) Field Descriptions
I2C
07h		FIELDTYPERESETDESCRIPTION
7-6ReservedR/W00b

Not used. 1 = invalid write.

5OTG Voltage, bit 11R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 16656 mV of OTG voltage.

4OTG Voltage, bit 10R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 8328 mV of OTG voltage.

3OTG Voltage, bit 9R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 4164 mV of OTG voltage.

2OTG Voltage, bit 8R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 2082 mV of OTG voltage.

1OTG Voltage, bit 7R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 1041 mV of OTG voltage.

0OTG Voltage, bit 6R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 521 mV of OTG voltage.

Table 9-36 OTGVoltage Register (I2C address = 06h) Field Descriptions
I2C
06h		FIELDTYPERESETDESCRIPTION
7OTG Voltage, bit 5R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 260 mV of OTG voltage.

6OTG Voltage, bit 4R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 130 mV of OTG voltage.

5OTG Voltage, bit 3R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 65 mV of OTG voltage.

4OTG Voltage, bit 2R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 33 mV of OTG voltage.

3OTG Voltage, bit 1R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 16 mV of OTG voltage.

2OTG Voltage, bit 0R/W0b

0 = Adds 0 mV of OTG voltage.

1 = Adds 8.1 mV of OTG voltage.

1-0ReservedR/W00bNot used. Value Ignored.