JAJSFQ9C june   2018  – may 2023 BQ25713 , BQ25713B

PRODUCTION DATA  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 概要 (続き)
  7. 6 Device Comparison Table
  8. 7 Pin Configuration and Functions
  9. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Typical Characteristics
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1  Power-Up from Battery Without DC Source
      2. 9.3.2  Vmin Active Protection (VAP) when Battery only Mode
      3. 9.3.3  Power-Up From DC Source
        1. 9.3.3.1 CHRG_OK Indicator
        2. 9.3.3.2 Input Voltage and Current Limit Setup
        3. 9.3.3.3 Battery Cell Configuration
        4. 9.3.3.4 Device Hi-Z State
      4. 9.3.4  USB On-The-Go (OTG)
      5. 9.3.5  Converter Operation
        1. 9.3.5.1 Inductance Detection Through IADPT Pin
        2. 9.3.5.2 Continuous Conduction Mode (CCM)
        3. 9.3.5.3 Pulse Frequency Modulation (PFM)
      6. 9.3.6  Current and Power Monitor
        1. 9.3.6.1 High-Accuracy Current Sense Amplifier (IADPT and IBAT)
        2. 9.3.6.2 High-Accuracy Power Sense Amplifier (PSYS)
      7. 9.3.7  Input Source Dynamic Power Manage
      8. 9.3.8  Two-Level Adapter Current Limit (Peak Power Mode)
      9. 9.3.9  Processor Hot Indication
        1. 9.3.9.1 PROCHOT During Low Power Mode
        2. 9.3.9.2 PROCHOT Status
      10. 9.3.10 Device Protection
        1. 9.3.10.1 Watchdog Timer
        2. 9.3.10.2 Input Overvoltage Protection (ACOV)
        3. 9.3.10.3 Input Overcurrent Protection (ACOC)
        4. 9.3.10.4 System Overvoltage Protection (SYSOVP)
        5. 9.3.10.5 Battery Overvoltage Protection (BATOVP)
        6. 9.3.10.6 Battery Short
        7. 9.3.10.7 System Short Hiccup Mode
        8. 9.3.10.8 Thermal Shutdown (TSHUT)
    4. 9.4 Device Functional Modes
      1. 9.4.1 Forward Mode
        1. 9.4.1.1 System Voltage Regulation with Narrow VDC Architecture
        2. 9.4.1.2 Battery Charging
      2. 9.4.2 USB On-The-Go
      3. 9.4.3 Pass Through Mode (PTM)
    5. 9.5 Programming
      1. 9.5.1 I2C Serial Interface
        1. 9.5.1.1 Data Validity
        2. 9.5.1.2 START and STOP Conditions
        3. 9.5.1.3 Byte Format
        4. 9.5.1.4 Acknowledge (ACK) and Not Acknowledge (NACK)
        5. 9.5.1.5 Slave Address and Data Direction Bit
        6. 9.5.1.6 Single Read and Write
        7. 9.5.1.7 Multi-Read and Multi-Write
        8. 9.5.1.8 Write 2-Byte I2C Commands
    6. 9.6 Register Map
      1. 9.6.1  Setting Charge and PROCHOT Options
        1. 9.6.1.1 ChargeOption0 Register (I2C address = 01/00h) [reset = E70Eh]
        2. 9.6.1.2 ChargeOption1 Register (I2C address = 31/30h) [reset = 0211h]
        3. 9.6.1.3 ChargeOption2 Register (I2C address = 33/32h) [reset = 02B7h]
        4. 9.6.1.4 ChargeOption3 Register (I2C address = 35/34h) [reset = 0030h]
        5. 9.6.1.5 ProchotOption0 Register (I2C address = 37/36h) [reset = 4A65h]
        6. 9.6.1.6 ProchotOption1 Register (I2C address = 39/38h) [reset = 81A0h]
        7. 9.6.1.7 ADCOption Register (I2C address = 3B/3Ah) [reset = 2000h]
      2. 9.6.2  Charge and PROCHOT Status
        1. 9.6.2.1 ChargerStatus Register (I2C address = 21/20h) [reset = 0000h]
        2. 9.6.2.2 ProchotStatus Register (I2C address = 23/22h) [reset = A800h]
      3. 9.6.3  ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]
        1. 9.6.3.1 Battery Precharge Current Clamp
      4. 9.6.4  MaxChargeVoltage Register (I2C address = 05/04h) [reset value based on CELL_BATPRESZ pin setting]
      5. 9.6.5  MinSystemVoltage Register (I2C address = 0D/0Ch) [reset value based on CELL_BATPRESZ pin setting]
        1. 9.6.5.1 System Voltage Regulation
      6. 9.6.6  Input Current and Input Voltage Registers for Dynamic Power Management
        1. 9.6.6.1 Input Current Registers
          1. 9.6.6.1.1 IIN_HOST Register With 10-mΩ Sense Resistor (I2C address = 0F/0Eh) [reset = 4100h]
          2. 9.6.6.1.2 IIN_DPM Register With 10-mΩ Sense Resistor (I2C address = 25/24h) [reset = 4100h]
          3. 9.6.6.1.3 InputVoltage Register (I2C address = 0B/0Ah) [reset = VBUS-1.28V]
      7. 9.6.7  OTGVoltage Register (I2C address = 07/06h) [reset = 0000h]
      8. 9.6.8  OTGCurrent Register (I2C address = 09/08h) [reset = 0000h]
      9. 9.6.9  ADCVBUS/PSYS Register (I2C address = 27/26h)
      10. 9.6.10 ADCIBAT Register (I2C address = 29/28h)
      11. 9.6.11 ADCIINCMPIN Register (I2C address = 2B/2Ah)
      12. 9.6.12 ADCVSYSVBAT Register (I2C address = 2D/2Ch)
      13. 9.6.13 ID Registers
        1. 9.6.13.1 ManufactureID Register (I2C address = 2Eh) [reset = 0040h]
        2. 9.6.13.2 Device ID (DeviceAddress) Register (I2C address = 2Fh) [reset = 0h]
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 ACP-ACN Input Filter
        2. 10.2.2.2 Inductor Selection
        3. 10.2.2.3 Input Capacitor
        4. 10.2.2.4 Output Capacitor
        5. 10.2.2.5 Power MOSFETs Selection
      3. 10.2.3 Application Curves
  12. 11Power Supply Recommendations
  13. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
      1. 12.2.1 Layout Example Reference Top View
      2. 12.2.2 Inner Layer Layout and Routing Example
  14. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 サード・パーティ製品に関する免責事項
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 ドキュメントの更新通知を受け取る方法
    4. 13.4 サポート・リソース
    5. 13.5 Trademarks
    6. 13.6 静電気放電に関する注意事項
    7. 13.7 用語集
  15. 14Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.6.3 ChargeCurrent Register (I2C address = 03/02h) [reset = 0000h]

To set the charge current, write a 16-bit ChargeCurrent() command (REG0x03/02h()) using the data format listed in Figure 9-21, Table 9-23, and Table 9-24.

With 10-mΩ sense resistor, the charger provides charge current range of 64 mA to 8.128 A, with a 64-mA step resolution. Upon POR, when auto wakeup is not active, ChargeCurrent() is 0 A. Any conditions for CHRG_OK low except ACOV will reset ChargeCurrent() to zero. CELL_BATPRESZ going LOW (battery removal) will reset the ChargeCurrent() register to 0 A.

Charge current is not reset in ACOC, TSHUT, power path latch off (REG0x30[1]), and SYSOVP.

A 0.1-µF capacitor between SRP and SRN for differential mode filtering is recommended; an optional 0.1-µF capacitor between SRN and ground, and an optional 0.1-µF capacitor between SRP and ground for common mode filtering. Meanwhile, the capacitance on SRP should not be higher than 0.1 µF in order to properly sense the voltage across SRP and SRN for cycle-by-cycle current detection.

The SRP and SRN pins are used to sense voltage drop across RSR with default value of 10 mΩ. However, resistors of other values can also be used. For a larger sense resistor, a larger sense voltage is given, and a higher regulation accuracy; but, at the expense of higher conduction loss. A current sensing resistor value no more than 20 mΩ is suggested.

Figure 9-21 ChargeCurrent Register With 10-mΩ Sense Resistor (I2C address = 03/02h) [reset = 0h]
76543210
ReservedCharge Current, bit 6Charge Current, bit 5Charge Current, bit 4Charge Current, bit 3Charge Current, bit 2
R/WR/WR/WR/WR/WR/W
76543210
Charge Current, bit 1Charge Current, bit 0ReservedReserved
R/WR/WR/WR/W
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 9-23 Charge Current Register (14h) With 10-mΩ Sense Resistor (I2C address = 03h) Field Descriptions
I2C
03h		FIELDTYPERESETDESCRIPTION
7-5ReservedR/W000b

Not used. 1 = invalid write.

4Charge Current, bit 6R/W0b

0 = Adds 0 mA of charger current.

1 = Adds 4096 mA of charger current.

3Charge Current, bit 5R/W0b

0 = Adds 0 mA of charger current.

1 = Adds 2048 mA of charger current.

2Charge Current, bit 4R/W0b

0 = Adds 0 mA of charger current.

1 = Adds 1024 mA of charger current.

1Charge Current, bit 3R/W0b

0 = Adds 0 mA of charger current.

1 = Adds 512 mA of charger current.

0Charge Current, bit 2R/W0b

0 = Adds 0 mA of charger current.

1 = Adds 256 mA of charger current.

Table 9-24 Charge Current Register (14h) With 10-mΩ Sense Resistor (I2C address = 02h) Field Descriptions
I2C
02h		FIELDTYPERESETDESCRIPTION
7Charge Current, bit 1R/W0b

0 = Adds 0 mA of charger current.

1 = Adds 128 mA of charger current.

6Charge Current, bit 0R/W0b

0 = Adds 0 mA of charger current.

1 = Adds 64 mA of charger current.

5-0ReservedR/W000000b

Not used. Value Ignored.