JAJSD07C September   2016  – December 2022 DS90UB934-Q1

PRODUCTION DATA  

  1.   特長
  2. 1アプリケーション
  3. 2概要
  4. 3Revision History
  5.   Pin Configuration and Functions
  6. 4Specifications
    1. 4.1 Absolute Maximum Ratings
    2. 4.2 ESD Ratings
    3. 4.3 Recommended Operating Conditions
    4. 4.4 Thermal Information
    5. 4.5 DC Electrical Characteristics
    6. 4.6 AC Electrical Characteristics
    7. 4.7 Recommended Timing for the Serial Control Bus
    8. 4.8 Typical Characteristics
  7. 5Detailed Description
    1. 5.1 Overview
      1. 5.1.1 Functional Description
    2. 5.2 Functional Block Diagram
    3. 5.3 Feature Description
      1. 5.3.1 Serial Frame Format
      2. 5.3.2 Line Rate Calculations for the DS90UB933/934
      3. 5.3.3 Deserializer Multiplexer Input
    4. 5.4 Device Functional Modes
      1. 5.4.1 RX MODE Pin
      2. 5.4.2 DVP Output Control
        1. 5.4.2.1 LOCK Status
      3. 5.4.3 Input Jitter Tolerance
      4. 5.4.4 Adaptive Equalizer
      5. 5.4.5 Channel Monitor Loop-Through Output Driver
        1. 5.4.5.1 Code Example for CMLOUT FPD3 RX Port 0:
      6. 5.4.6 GPIO Support
        1. 5.4.6.1 Back Channel GPIO
        2. 5.4.6.2 GPIO Pin Status
        3. 5.4.6.3 Other GPIO Pin Controls
        4. 5.4.6.4 FrameSync Operation
          1. 5.4.6.4.1 External FrameSync Control
          2. 5.4.6.4.2 Internally Generated FrameSync
            1. 5.4.6.4.2.1 Code Example for Internally Generated FrameSync
    5. 5.5 Programming
      1. 5.5.1 Serial Control Bus
        1. 5.5.1.1 I2C Target Operation
        2. 5.5.1.2 Remote Target Operation
        3. 5.5.1.3 Remote I2C Targets Data Throughput
        4. 5.5.1.4 Remote Target Addressing
        5. 5.5.1.5 Broadcast Write to Remote Target Devices
        6. 5.5.1.6 Code Example for Broadcast Write
      2. 5.5.2 Interrupt Support
        1. 5.5.2.1 Code Example to Enable Interrupts
        2. 5.5.2.2 FPD-Link III Receive Port Interrupts
        3. 5.5.2.3 Code Example to Readback Interrupts
        4. 5.5.2.4 Built-In Self Test (BIST)
          1. 5.5.2.4.1 BIST Configuration and Status
    6. 5.6 Register Maps
      1. 5.6.1 Register Description
      2. 5.6.2 Registers
      3. 5.6.3 Indirect Access Registers
      4. 5.6.4 Indirect Access Register Map
        1. 5.6.4.1 FPD3 Channel 0 Registers
        2. 5.6.4.2 FPD3 Channel 1 Registers
        3. 5.6.4.3 FPD3 RX Shared Registers
  8. 6Application and Implementation
    1. 6.1 Application Information
    2. 6.2 Power Over Coax
    3. 6.3 Typical Application
      1. 6.3.1 Design Requirements
      2. 6.3.2 Detailed Design Procedure
      3. 6.3.3 Application Curves
    4. 6.4 System Examples
    5. 6.5 Power Supply Recommendations
      1. 6.5.1 VDD Power Supply
      2. 6.5.2 Power-Up Sequencing
      3. 6.5.3 PDB Pin
      4. 6.5.4 Ground
    6. 6.6 Layout
      1. 6.6.1 Layout Guidelines
        1. 6.6.1.1 DVP Interface Guidelines
      2. 6.6.2 Layout Example
  9.   Mechanical, Packaging, and Orderable Information
  10. 7Device and Documentation Support
    1. 7.1 Documentation Support
      1. 7.1.1 Related Documentation
    2. 7.2 Glossary
    3. 7.3 Receiving Notification of Documentation Updates
    4. 7.4 サポート・リソース
    5. 7.5 Trademarks
  11.   Mechanical, Packaging, and Orderable Information

FPD3 RX Shared Registers

Table 5-14 FPD3 RX Shared Registers
Page Addr (hex) Register Name Bit(s) Field Type Default Description
5 0x00 REG_0_SH 7 LOOP_EN R/W 0x0 Enable CMLOUT loop through driver
0: disabled (default)
1: enabled
6 RESERVED R/W 0x0 Reserved
5 RESERVED R/W 0x0 Reserved
4 RESERVED R/W 0x0 Reserved
3 RESERVED R/W 0x0 Reserved
2:0 RESERVED R/W 0x0 Reserved
5 0x01 RESERVED 7:0 RESERVED R/W 0x0 Reserved
5 0x02 REG_2_SH 7 SEL_CHANNEL R/W 0x0 Loop through RX Monitor MUX
0: CH0
1: CH1
6:5 RESERVED R/W 0x1 Reserved
4:0 RESERVED R/W 0x0 Reserved
5 0x03 REG3_SH_STP 7:6 RESERVED R/W 0x0 Reserved
5 EN_TERM_STP R/W 0x0 Enable CMLOUT loop termination
0: Disable
1: Enable
4 RESERVED R/W 0x0 Reserved
3:0 RESERVED R/W 0x8 Reserved
5 0x04 REG3_SH_COAX 7:6 RESERVED R/W 0x0 Reserved
5 EN_TERM_COAX R/W 0x0 Enable CMLOUT loop termination
0: Disable
1: Enable
4 RESERVED R/W 0x0 Reserved
3:0 RESERVED R/W 0x8 Reserved