SLUUBY1B December   2020  – April 2022 BQ76942

 

  1.   Read This First
    1.     About This Manual
    2.     Battery Notational Conventions
    3.     Trademarks
    4.     Glossary
  2. Introduction
  3. Device Description
    1. 2.1 Overview
    2. 2.2 Functional Block Diagram
  4. Device Configuration
    1. 3.1 Direct Commands and Subcommands
    2. 3.2 Configuration Using OTP or Registers
    3. 3.3 Device Version Differences
    4. 3.4 Data Formats
      1. 3.4.1 Unsigned Integer
      2. 3.4.2 Integer
      3. 3.4.3 Floating Point
      4. 3.4.4 Hex
  5. Measurement Subsystem
    1. 4.1  Voltage Measurement
      1. 4.1.1 Voltage Measurement Schedule
      2. 4.1.2 Usage of VC Pins for Cells Versus Interconnect
      3. 4.1.3 Cell Interconnect Resistance
    2. 4.2  General Purpose ADCIN Functionality
    3. 4.3  Coulomb Counter and Digital Filters
    4. 4.4  Synchronized Voltage and Current Measurement
    5. 4.5  Subcommands 0x0071–0x0073 DASTATUS1-3() , Cell Voltage and Synchronized Current Counts
    6. 4.6  Subcommands 0x0075–0x0077 DASTATUS5-7(), Additional Measurements
    7. 4.7  Internal Temperature Measurement
    8. 4.8  Thermistor Temperature Measurement
    9. 4.9  Factory Trim of Voltage ADC
    10. 4.10 Voltage Calibration (ADC Measurements)
    11. 4.11 Voltage Calibration (COV and CUV Protections)
    12. 4.12 Current Calibration
    13. 4.13 Temperature Calibration
  6. Primary and Secondary Protection Subsystems
    1. 5.1 Protections Overview
    2. 5.2 Primary Protections
      1. 5.2.1  Primary Protections Overview
      2. 5.2.2  High-Side NFET Drivers
      3. 5.2.3  Protection FETs Configuration and Control
        1. 5.2.3.1 FET Configuration
        2. 5.2.3.2 FET Control
          1. 5.2.3.2.1 Precharge Mode
          2. 5.2.3.2.2 Predischarge Mode
      4. 5.2.4  Cell Overvoltage Protection
      5. 5.2.5  Cell Undervoltage Protection
      6. 5.2.6  Short Circuit in Discharge Protection
      7. 5.2.7  Overcurrent in Charge Protection
      8. 5.2.8  Overcurrent in Discharge 1, 2, and 3 Protections
      9. 5.2.9  Overtemperature in Charge Protection
      10. 5.2.10 Overtemperature in Discharge Protection
      11. 5.2.11 Overtemperature FET Protection
      12. 5.2.12 Internal Overtemperature Protection
      13. 5.2.13 Undertemperature in Charge Protection
      14. 5.2.14 Undertemperature in Discharge Protection
      15. 5.2.15 Internal Undertemperature Protection
      16. 5.2.16 Host Watchdog Protection
      17. 5.2.17 Precharge Timeout Protection
      18. 5.2.18 Load Detect Functionality
    3. 5.3 Secondary Protections
      1. 5.3.1  Secondary Protections Overview
      2. 5.3.2  Copper Deposition (CUDEP) Permanent Fail
      3. 5.3.3  Safety Undervoltage (SUV) Permanent Fail
      4. 5.3.4  Safety Overvoltage (SOV) Permanent Fail
      5. 5.3.5  Safety Overcurrent in Charge (SOCC) Permanent Fail
      6. 5.3.6  Safety Overcurrent in Discharge (SOCD) Permanent Fail
      7. 5.3.7  Safety Cell Overtemperature (SOT) Permanent Fail
      8. 5.3.8  Safety FET Overtemperature (SOTF) Permanent Fail
      9. 5.3.9  Charge FET (CFETF) Permanent Fail
      10. 5.3.10 Discharge FET (DFETF) Permanent Fail
      11. 5.3.11 Secondary Protector (2LVL) Permanent Fail
      12. 5.3.12 Voltage Imbalance in Relax (VIMR) Permanent Fail
      13. 5.3.13 Voltage Imbalance in Active (VIMA) Permanent Fail
      14. 5.3.14 Short Circuit in Discharge Latched Permanent Fail
      15. 5.3.15 OTP Memory Signature Permanent Fail
      16. 5.3.16 Data ROM Memory Signature Permanent Fail
      17. 5.3.17 Instruction ROM Memory Signature Permanent Fail
      18. 5.3.18 LFO Oscillator Permanent Fail
      19. 5.3.19 Voltage Reference Permanent Fail
      20. 5.3.20 VSS Permanent Fail
      21. 5.3.21 Protection Comparator MUX Permanent Fail
      22. 5.3.22 Commanded Permanent Fail
      23. 5.3.23 Top of Stack Measurement Check
      24. 5.3.24 Cell Open Wire
  7. Device Status and Controls
    1. 6.1 0x00 Control Status() and 0x12 Battery Status() Commands
    2. 6.2 0x0070 MANU_DATA() Subcommand
    3. 6.3 LDOs
      1. 6.3.1 Preregulator Control
      2. 6.3.2 REG1 and REG2 LDO Controls
    4. 6.4 Multifunction Pin Controls
    5. 6.5 CFETOFF, DFETOFF, and BOTHOFF Pin Functionality
    6. 6.6 ALERT Pin Operation
    7. 6.7 DDSG and DCHG Pin Operation
    8. 6.8 Fuse Drive
    9. 6.9 Device Event Timing
  8. Operational Modes
    1. 7.1 Overview
    2. 7.2 NORMAL Mode
    3. 7.3 SLEEP Mode
    4. 7.4 DEEPSLEEP Mode
    5. 7.5 SHUTDOWN Mode
    6. 7.6 CONFIG_UPDATE Mode
  9. Device Security
    1. 8.1 Overview
  10. Serial Communications Interfaces
    1. 9.1 Serial Communications Overview
    2. 9.2 I2C Communications Subsystem
    3. 9.3 SPI Communications Interface
      1. 9.3.1 SPI Protocol
    4. 9.4 HDQ Communications Interface
  11. 10Cell Balancing
    1. 10.1 Cell Balancing Operation
    2. 10.2 Cell Balancing Timing
  12. 11Diagnostics
    1. 11.1 Diagnostics Overview
    2. 11.2 VREF2 Versus VREF1 Check
    3. 11.3 VSS Measurement
    4. 11.4 Top of Stack Measurement Check
    5. 11.5 LFO Oscillator Monitor
    6. 11.6 Protection Comparator Mux Check
    7. 11.7 Internal Watchdog Reset
    8. 11.8 Internal Memory Checks
  13. 12Commands and Subcommands
    1. 12.1 Direct Commands
    2. 12.2 Bitfield Definitions for Direct Commands
      1. 12.2.1  Control Status Register
      2. 12.2.2  Safety Alert A Register
      3. 12.2.3  Safety Status A Register
      4. 12.2.4  Safety Alert B Register
      5. 12.2.5  Safety Status B Register
      6. 12.2.6  Safety Alert C Register
      7. 12.2.7  Safety Status C Register
      8. 12.2.8  PF Alert A Register
      9. 12.2.9  PF Status A Register
      10. 12.2.10 PF Alert B Register
      11. 12.2.11 PF Status B Register
      12. 12.2.12 PF Alert C Register
      13. 12.2.13 PF Status C Register
      14. 12.2.14 PF Alert D Register
      15. 12.2.15 PF Status D Register
      16. 12.2.16 Battery Status Register
      17. 12.2.17 Alarm Status Register
      18. 12.2.18 Alarm Raw Status Register
      19. 12.2.19 Alarm Enable Register
      20. 12.2.20 FET Status Register
    3. 12.3 Command-Only Subcommands
    4. 12.4 Subcommands with Data
    5. 12.5 Bitfield Definitions for Subcommands
      1. 12.5.1 PF Status A Register
      2. 12.5.2 PF Status B Register
      3. 12.5.3 PF Status C Register
      4. 12.5.4 PF Status D Register
      5. 12.5.5 Manufacturing Status Register
      6. 12.5.6 FET Control Register
      7. 12.5.7 REG12 Control Register
      8. 12.5.8 OTP Write Check Result Register
      9. 12.5.9 OTP Write Result Register
  14. 13Data Memory Settings
    1. 13.1 Data Memory Access
    2. 13.2 Calibration
      1. 13.2.1  Calibration:Voltage
        1. 13.2.1.1  Calibration:Voltage:Cell 1 Gain
        2. 13.2.1.2  Calibration:Voltage:Cell 2 Gain
        3. 13.2.1.3  Calibration:Voltage:Cell 3 Gain
        4. 13.2.1.4  Calibration:Voltage:Cell 4 Gain
        5. 13.2.1.5  Calibration:Voltage:Cell 5 Gain
        6. 13.2.1.6  Calibration:Voltage:Cell 6 Gain
        7. 13.2.1.7  Calibration:Voltage:Cell 7 Gain
        8. 13.2.1.8  Calibration:Voltage:Cell 8 Gain
        9. 13.2.1.9  Calibration:Voltage:Cell 9 Gain
        10. 13.2.1.10 Calibration:Voltage:Cell 10 Gain
        11. 13.2.1.11 Calibration:Voltage:Pack Gain
        12. 13.2.1.12 Calibration:Voltage:TOS Gain
        13. 13.2.1.13 Calibration:Voltage:LD Gain
        14. 13.2.1.14 Calibration:Voltage:ADC Gain
      2. 13.2.2  Calibration:Current
        1. 13.2.2.1 Calibration:Current:CC Gain
        2. 13.2.2.2 Calibration:Current:Capacity Gain
      3. 13.2.3  Calibration:Vcell Offset
        1. 13.2.3.1 Calibration:Vcell Offset:Vcell Offset
      4. 13.2.4  Calibration:V Divider Offset
        1. 13.2.4.1 Calibration:V Divider Offset:Vdiv Offset
      5. 13.2.5  Calibration:Current Offset
        1. 13.2.5.1 Calibration:Current Offset:Coulomb Counter Offset Samples
        2. 13.2.5.2 Calibration:Current Offset:Board Offset
      6. 13.2.6  Calibration:Temperature
        1. 13.2.6.1  Calibration:Temperature:Internal Temp Offset
        2. 13.2.6.2  Calibration:Temperature:CFETOFF Temp Offset
        3. 13.2.6.3  Calibration:Temperature:DFETOFF Temp Offset
        4. 13.2.6.4  Calibration:Temperature:ALERT Temp Offset
        5. 13.2.6.5  Calibration:Temperature:TS1 Temp Offset
        6. 13.2.6.6  Calibration:Temperature:TS2 Temp Offset
        7. 13.2.6.7  Calibration:Temperature:TS3 Temp Offset
        8. 13.2.6.8  Calibration:Temperature:HDQ Temp Offset
        9. 13.2.6.9  Calibration:Temperature:DCHG Temp Offset
        10. 13.2.6.10 Calibration:Temperature:DDSG Temp Offset
      7. 13.2.7  Calibration:Internal Temp Model
        1. 13.2.7.1 Calibration:Internal Temp Model:Int Gain
        2. 13.2.7.2 Calibration:Internal Temp Model:Int base offset
        3. 13.2.7.3 Calibration:Internal Temp Model:Int Maximum AD
        4. 13.2.7.4 Calibration:Internal Temp Model:Int Maximum Temp
      8. 13.2.8  Calibration:18K Temperature Model
        1. 13.2.8.1  Calibration:18K Temperature Model:Coeff a1
        2. 13.2.8.2  Calibration:18K Temperature Model:Coeff a2
        3. 13.2.8.3  Calibration:18K Temperature Model:Coeff a3
        4. 13.2.8.4  Calibration:18K Temperature Model:Coeff a4
        5. 13.2.8.5  Calibration:18K Temperature Model:Coeff a5
        6. 13.2.8.6  Calibration:18K Temperature Model:Coeff b1
        7. 13.2.8.7  Calibration:18K Temperature Model:Coeff b2
        8. 13.2.8.8  Calibration:18K Temperature Model:Coeff b3
        9. 13.2.8.9  Calibration:18K Temperature Model:Coeff b4
        10. 13.2.8.10 Calibration:18K Temperature Model:Adc0
      9. 13.2.9  Calibration:180K Temperature Model
        1. 13.2.9.1  Calibration:180K Temperature Model:Coeff a1
        2. 13.2.9.2  Calibration:180K Temperature Model:Coeff a2
        3. 13.2.9.3  Calibration:180K Temperature Model:Coeff a3
        4. 13.2.9.4  Calibration:180K Temperature Model:Coeff a4
        5. 13.2.9.5  Calibration:180K Temperature Model:Coeff a5
        6. 13.2.9.6  Calibration:180K Temperature Model:Coeff b1
        7. 13.2.9.7  Calibration:180K Temperature Model:Coeff b2
        8. 13.2.9.8  Calibration:180K Temperature Model:Coeff b3
        9. 13.2.9.9  Calibration:180K Temperature Model:Coeff b4
        10. 13.2.9.10 Calibration:180K Temperature Model:Adc0
      10. 13.2.10 Calibration:Custom Temperature Model
        1. 13.2.10.1  Calibration:Custom Temperature Model:Coeff a1
        2. 13.2.10.2  Calibration:Custom Temperature Model:Coeff a2
        3. 13.2.10.3  Calibration:Custom Temperature Model:Coeff a3
        4. 13.2.10.4  Calibration:Custom Temperature Model:Coeff a4
        5. 13.2.10.5  Calibration:Custom Temperature Model:Coeff a5
        6. 13.2.10.6  Calibration:Custom Temperature Model:Coeff b1
        7. 13.2.10.7  Calibration:Custom Temperature Model:Coeff b2
        8. 13.2.10.8  Calibration:Custom Temperature Model:Coeff b3
        9. 13.2.10.9  Calibration:Custom Temperature Model:Coeff b4
        10. 13.2.10.10 Calibration:Custom Temperature Model:Rc0
        11. 13.2.10.11 Calibration:Custom Temperature Model:Adc0
      11. 13.2.11 Calibration:Current Deadband
        1. 13.2.11.1 Calibration:Current Deadband:Coulomb Counter Deadband
      12. 13.2.12 Calibration:CUV
        1. 13.2.12.1 Calibration:CUV:CUV Threshold Override
      13. 13.2.13 Calibration:COV
        1. 13.2.13.1 Calibration:COV:COV Threshold Override
    3. 13.3 Settings
      1. 13.3.1  Settings:Fuse
        1. 13.3.1.1 Settings:Fuse:Min Blow Fuse Voltage
        2. 13.3.1.2 Settings:Fuse:Fuse Blow Timeout
      2. 13.3.2  Settings:Configuration
        1. 13.3.2.1  Settings:Configuration:Power Config
        2. 13.3.2.2  Settings:Configuration:REG12 Config
        3. 13.3.2.3  Settings:Configuration:REG0 Config
        4. 13.3.2.4  Settings:Configuration:HWD Regulator Options
        5. 13.3.2.5  Settings:Configuration:Comm Type
        6. 13.3.2.6  Settings:Configuration:I2C Address
        7. 13.3.2.7  Settings:Configuration:SPI Configuration
        8. 13.3.2.8  Settings:Configuration:Comm Idle Time
        9. 13.3.2.9  Settings:Configuration:CFETOFF Pin Config
        10. 13.3.2.10 Settings:Configuration:DFETOFF Pin Config
        11. 13.3.2.11 Settings:Configuration:ALERT Pin Config
        12. 13.3.2.12 Settings:Configuration:TS1 Config
        13. 13.3.2.13 Settings:Configuration:TS2 Config
        14. 13.3.2.14 Settings:Configuration:TS3 Config
        15. 13.3.2.15 Settings:Configuration:HDQ Pin Config
        16. 13.3.2.16 Settings:Configuration:DCHG Pin Config
        17. 13.3.2.17 Settings:Configuration:DDSG Pin Config
        18. 13.3.2.18 Settings:Configuration:DA Configuration
        19. 13.3.2.19 Settings:Configuration:Vcell Mode
        20. 13.3.2.20 Settings:Configuration:CC3 Samples
      3. 13.3.3  Settings:Protection
        1. 13.3.3.1  Settings:Protection:Protection Configuration
        2. 13.3.3.2  Settings:Protection:Enabled Protections A
        3. 13.3.3.3  Settings:Protection:Enabled Protections B
        4. 13.3.3.4  Settings:Protection:Enabled Protections C
        5. 13.3.3.5  Settings:Protection:CHG FET Protections A
        6. 13.3.3.6  Settings:Protection:CHG FET Protections B
        7. 13.3.3.7  Settings:Protection:CHG FET Protections C
        8. 13.3.3.8  Settings:Protection:DSG FET Protections A
        9. 13.3.3.9  Settings:Protection:DSG FET Protections B
        10. 13.3.3.10 Settings:Protection:DSG FET Protections C
        11. 13.3.3.11 Settings:Protection:Body Diode Threshold
      4. 13.3.4  Settings:Alarm
        1. 13.3.4.1 Settings:Alarm:Default Alarm Mask
        2. 13.3.4.2 Settings:Alarm:SF Alert Mask A
        3. 13.3.4.3 Settings:Alarm:SF Alert Mask B
        4. 13.3.4.4 Settings:Alarm:SF Alert Mask C
        5. 13.3.4.5 Settings:Alarm:PF Alert Mask A
        6. 13.3.4.6 Settings:Alarm:PF Alert Mask B
        7. 13.3.4.7 Settings:Alarm:PF Alert Mask C
        8. 13.3.4.8 Settings:Alarm:PF Alert Mask D
      5. 13.3.5  Settings:Permanent Failure
        1. 13.3.5.1 Settings:Permanent Failure:Enabled PF A
        2. 13.3.5.2 Settings:Permanent Failure:Enabled PF B
        3. 13.3.5.3 Settings:Permanent Failure:Enabled PF C
        4. 13.3.5.4 Settings:Permanent Failure:Enabled PF D
      6. 13.3.6  Settings:FET
        1. 13.3.6.1 Settings:FET:FET Options
        2. 13.3.6.2 Settings:FET:Chg Pump Control
        3. 13.3.6.3 Settings:FET:Precharge Start Voltage
        4. 13.3.6.4 Settings:FET:Precharge Stop Voltage
        5. 13.3.6.5 Settings:FET:Predischarge Timeout
        6. 13.3.6.6 Settings:FET:Predischarge Stop Delta
      7. 13.3.7  Settings:Current Thresholds
        1. 13.3.7.1 Settings:Current Thresholds:Dsg Current Threshold
        2. 13.3.7.2 Settings:Current Thresholds:Chg Current Threshold
      8. 13.3.8  Settings:Cell Open-Wire
        1. 13.3.8.1 Settings:Cell Open-Wire:Check Time
      9. 13.3.9  Settings:Interconnect Resistances
        1. 13.3.9.1  Settings:Interconnect Resistances:Cell 1 Interconnect
        2. 13.3.9.2  Settings:Interconnect Resistances:Cell 2 Interconnect
        3. 13.3.9.3  Settings:Interconnect Resistances:Cell 3 Interconnect
        4. 13.3.9.4  Settings:Interconnect Resistances:Cell 4 Interconnect
        5. 13.3.9.5  Settings:Interconnect Resistances:Cell 5 Interconnect
        6. 13.3.9.6  Settings:Interconnect Resistances:Cell 6 Interconnect
        7. 13.3.9.7  Settings:Interconnect Resistances:Cell 7 Interconnect
        8. 13.3.9.8  Settings:Interconnect Resistances:Cell 8 Interconnect
        9. 13.3.9.9  Settings:Interconnect Resistances:Cell 9 Interconnect
        10. 13.3.9.10 Settings:Interconnect Resistances:Cell 10 Interconnect
      10. 13.3.10 Settings:Manufacturing
        1. 13.3.10.1 Settings:Manufacturing:Mfg Status Init
      11. 13.3.11 Settings:Cell Balancing Config
        1. 13.3.11.1  Settings:Cell Balancing Config:Balancing Configuration
        2. 13.3.11.2  Settings:Cell Balancing Config:Min Cell Temp
        3. 13.3.11.3  Settings:Cell Balancing Config:Max Cell Temp
        4. 13.3.11.4  Settings:Cell Balancing Config:Max Internal Temp
        5. 13.3.11.5  Settings:Cell Balancing Config:Cell Balance Interval
        6. 13.3.11.6  Settings:Cell Balancing Config:Cell Balance Max Cells
        7. 13.3.11.7  Settings:Cell Balancing Config:Cell Balance Min Cell V (Charge)
        8. 13.3.11.8  Settings:Cell Balancing Config:Cell Balance Min Delta (Charge)
        9. 13.3.11.9  Settings:Cell Balancing Config:Cell Balance Stop Delta (Charge)
        10. 13.3.11.10 Settings:Cell Balancing Config:Cell Balance Min Cell V (Relax)
        11. 13.3.11.11 Settings:Cell Balancing Config:Cell Balance Min Delta (Relax)
        12. 13.3.11.12 Settings:Cell Balancing Config:Cell Balance Stop Delta (Relax)
    4. 13.4 Power
      1. 13.4.1 Power:Shutdown
        1. 13.4.1.1 Power:Shutdown:Shutdown Cell Voltage
        2. 13.4.1.2 Power:Shutdown:Shutdown Stack Voltage
        3. 13.4.1.3 Power:Shutdown:Low V Shutdown Delay
        4. 13.4.1.4 Power:Shutdown:Shutdown Temperature
        5. 13.4.1.5 Power:Shutdown:Shutdown Temperature Delay
        6. 13.4.1.6 Power:Shutdown:FET Off Delay
        7. 13.4.1.7 Power:Shutdown:Shutdown Command Delay
        8. 13.4.1.8 Power:Shutdown:Auto Shutdown Time
        9. 13.4.1.9 Power:Shutdown:RAM Fail Shutdown Time
      2. 13.4.2 Power:Sleep
        1. 13.4.2.1 Power:Sleep:Sleep Current
        2. 13.4.2.2 Power:Sleep:Voltage Time
        3. 13.4.2.3 Power:Sleep:Wake Comparator Current
        4. 13.4.2.4 Power:Sleep:Sleep Hysteresis Time
        5. 13.4.2.5 Power:Sleep:Sleep Charger Voltage Threshold
        6. 13.4.2.6 Power:Sleep:Sleep Charger PACK-TOS Delta
    5. 13.5 System Data
      1. 13.5.1 System Data:Integrity
        1. 13.5.1.1 System Data:Integrity:Config RAM Signature
    6. 13.6 Protections
      1. 13.6.1  Protections:CUV
        1. 13.6.1.1 Protections:CUV:Threshold
        2. 13.6.1.2 Protections:CUV:Delay
        3. 13.6.1.3 Protections:CUV:Recovery Hysteresis
      2. 13.6.2  Protections:COV
        1. 13.6.2.1 Protections:COV:Threshold
        2. 13.6.2.2 Protections:COV:Delay
        3. 13.6.2.3 Protections:COV:Recovery Hysteresis
      3. 13.6.3  Protections:COVL
        1. 13.6.3.1 Protections:COVL:Latch Limit
        2. 13.6.3.2 Protections:COVL:Counter Dec Delay
        3. 13.6.3.3 Protections:COVL:Recovery Time
      4. 13.6.4  Protections:OCC
        1. 13.6.4.1 Protections:OCC:Threshold
        2. 13.6.4.2 Protections:OCC:Delay
        3. 13.6.4.3 Protections:OCC:Recovery Threshold
        4. 13.6.4.4 Protections:OCC:PACK-TOS Delta
      5. 13.6.5  Protections:OCD1
        1. 13.6.5.1 Protections:OCD1:Threshold
        2. 13.6.5.2 Protections:OCD1:Delay
      6. 13.6.6  Protections:OCD2
        1. 13.6.6.1 Protections:OCD2:Threshold
        2. 13.6.6.2 Protections:OCD2:Delay
      7. 13.6.7  Protections:SCD
        1. 13.6.7.1 Protections:SCD:Threshold
        2. 13.6.7.2 Protections:SCD:Delay
        3. 13.6.7.3 Protections:SCD:Recovery Time
      8. 13.6.8  Protections:OCD3
        1. 13.6.8.1 Protections:OCD3:Threshold
        2. 13.6.8.2 Protections:OCD3:Delay
      9. 13.6.9  Protections:OCD
        1. 13.6.9.1 Protections:OCD:Recovery Threshold
      10. 13.6.10 Protections:OCDL
        1. 13.6.10.1 Protections:OCDL:Latch Limit
        2. 13.6.10.2 Protections:OCDL:Counter Dec Delay
        3. 13.6.10.3 Protections:OCDL:Recovery Time
        4. 13.6.10.4 Protections:OCDL:Recovery Threshold
      11. 13.6.11 Protections:SCDL
        1. 13.6.11.1 Protections:SCDL:Latch Limit
        2. 13.6.11.2 Protections:SCDL:Counter Dec Delay
        3. 13.6.11.3 Protections:SCDL:Recovery Time
        4. 13.6.11.4 Protections:SCDL:Recovery Threshold
      12. 13.6.12 Protections:OTC
        1. 13.6.12.1 Protections:OTC:Threshold
        2. 13.6.12.2 Protections:OTC:Delay
        3. 13.6.12.3 Protections:OTC:Recovery
      13. 13.6.13 Protections:OTD
        1. 13.6.13.1 Protections:OTD:Threshold
        2. 13.6.13.2 Protections:OTD:Delay
        3. 13.6.13.3 Protections:OTD:Recovery
      14. 13.6.14 Protections:OTF
        1. 13.6.14.1 Protections:OTF:Threshold
        2. 13.6.14.2 Protections:OTF:Delay
        3. 13.6.14.3 Protections:OTF:Recovery
      15. 13.6.15 Protections:OTINT
        1. 13.6.15.1 Protections:OTINT:Threshold
        2. 13.6.15.2 Protections:OTINT:Delay
        3. 13.6.15.3 Protections:OTINT:Recovery
      16. 13.6.16 Protections:UTC
        1. 13.6.16.1 Protections:UTC:Threshold
        2. 13.6.16.2 Protections:UTC:Delay
        3. 13.6.16.3 Protections:UTC:Recovery
      17. 13.6.17 Protections:UTD
        1. 13.6.17.1 Protections:UTD:Threshold
        2. 13.6.17.2 Protections:UTD:Delay
        3. 13.6.17.3 Protections:UTD:Recovery
      18. 13.6.18 Protections:UTINT
        1. 13.6.18.1 Protections:UTINT:Threshold
        2. 13.6.18.2 Protections:UTINT:Delay
        3. 13.6.18.3 Protections:UTINT:Recovery
      19. 13.6.19 Protections:Recovery
        1. 13.6.19.1 Protections:Recovery:Time
      20. 13.6.20 Protections:HWD
        1. 13.6.20.1 Protections:HWD:Delay
      21. 13.6.21 Protections:Load Detect
        1. 13.6.21.1 Protections:Load Detect:Active Time
        2. 13.6.21.2 Protections:Load Detect:Retry Delay
        3. 13.6.21.3 Protections:Load Detect:Timeout
      22. 13.6.22 Protections:PTO
        1. 13.6.22.1 Protections:PTO:Charge Threshold
        2. 13.6.22.2 Protections:PTO:Delay
        3. 13.6.22.3 Protections:PTO:Reset
    7. 13.7 Permanent Fail
      1. 13.7.1  Permanent Fail:CUDEP
        1. 13.7.1.1 Permanent Fail:CUDEP:Threshold
        2. 13.7.1.2 Permanent Fail:CUDEP:Delay
      2. 13.7.2  Permanent Fail:SUV
        1. 13.7.2.1 Permanent Fail:SUV:Threshold
        2. 13.7.2.2 Permanent Fail:SUV:Delay
      3. 13.7.3  Permanent Fail:SOV
        1. 13.7.3.1 Permanent Fail:SOV:Threshold
        2. 13.7.3.2 Permanent Fail:SOV:Delay
      4. 13.7.4  Permanent Fail:TOS
        1. 13.7.4.1 Permanent Fail:TOS:Threshold
        2. 13.7.4.2 Permanent Fail:TOS:Delay
      5. 13.7.5  Permanent Fail:SOCC
        1. 13.7.5.1 Permanent Fail:SOCC:Threshold
        2. 13.7.5.2 Permanent Fail:SOCC:Delay
      6. 13.7.6  Permanent Fail:SOCD
        1. 13.7.6.1 Permanent Fail:SOCD:Threshold
        2. 13.7.6.2 Permanent Fail:SOCD:Delay
      7. 13.7.7  Permanent Fail:SOT
        1. 13.7.7.1 Permanent Fail:SOT:Threshold
        2. 13.7.7.2 Permanent Fail:SOT:Delay
      8. 13.7.8  Permanent Fail:SOTF
        1. 13.7.8.1 Permanent Fail:SOTF:Threshold
        2. 13.7.8.2 Permanent Fail:SOTF:Delay
      9. 13.7.9  Permanent Fail:VIMR
        1. 13.7.9.1 Permanent Fail:VIMR:Check Voltage
        2. 13.7.9.2 Permanent Fail:VIMR:Max Relax Current
        3. 13.7.9.3 Permanent Fail:VIMR:Threshold
        4. 13.7.9.4 Permanent Fail:VIMR:Delay
        5. 13.7.9.5 Permanent Fail:VIMR:Relax Min Duration
      10. 13.7.10 Permanent Fail:VIMA
        1. 13.7.10.1 Permanent Fail:VIMA:Check Voltage
        2. 13.7.10.2 Permanent Fail:VIMA:Min Active Current
        3. 13.7.10.3 Permanent Fail:VIMA:Threshold
        4. 13.7.10.4 Permanent Fail:VIMA:Delay
      11. 13.7.11 Permanent Fail:CFETF
        1. 13.7.11.1 Permanent Fail:CFETF:OFF Threshold
        2. 13.7.11.2 Permanent Fail:CFETF:OFF Delay
      12. 13.7.12 Permanent Fail:DFETF
        1. 13.7.12.1 Permanent Fail:DFETF:OFF Threshold
        2. 13.7.12.2 Permanent Fail:DFETF:OFF Delay
      13. 13.7.13 Permanent Fail:VSSF
        1. 13.7.13.1 Permanent Fail:VSSF:Fail Threshold
        2. 13.7.13.2 Permanent Fail:VSSF:Delay
      14. 13.7.14 Permanent Fail:2LVL
        1. 13.7.14.1 Permanent Fail:2LVL:Delay
      15. 13.7.15 Permanent Fail:LFOF
        1. 13.7.15.1 Permanent Fail:LFOF:Delay
      16. 13.7.16 Permanent Fail:HWMX
        1. 13.7.16.1 Permanent Fail:HWMX:Delay
    8. 13.8 Security
      1. 13.8.1 Security:Settings
        1. 13.8.1.1 Security:Settings:Security Settings
      2. 13.8.2 Security:Keys
        1. 13.8.2.1 Security:Keys:Unseal Key Step 1
        2. 13.8.2.2 Security:Keys:Unseal Key Step 2
        3. 13.8.2.3 Security:Keys:Full Access Key Step 1
        4. 13.8.2.4 Security:Keys:Full Access Key Step 2
    9. 13.9 Data Memory Summary
  15. 15Revision History

Data Memory Summary

Table 13-37 Data Memory Table
Class Subclass Address Name Type Min Value Max Value Default Units
Calibration Voltage 0x9180 Cell 1 Gain I2 –32767 32767 0
Calibration Voltage 0x9182 Cell 2 Gain I2 –32767 32767 0
Calibration Voltage 0x9184 Cell 3 Gain I2 –32767 32767 0
Calibration Voltage 0x9186 Cell 4 Gain I2 –32767 32767 0
Calibration Voltage 0x9188 Cell 5 Gain I2 –32767 32767 0
Calibration Voltage 0x918A Cell 6 Gain I2 –32767 32767 0
Calibration Voltage 0x918C Cell 7 Gain I2 –32767 32767 0
Calibration Voltage 0x918E Cell 8 Gain I2 –32767 32767 0
Calibration Voltage 0x9190 Cell 9 Gain I2 –32767 32767 0
Calibration Voltage 0x9192 Cell 10 Gain I2 –32767 32767 0
Calibration Voltage 0x91A0 Pack Gain U2 0 65535 0
Calibration Voltage 0x91A2 TOS Gain U2 0 65535 0
Calibration Voltage 0x91A4 LD Gain U2 0 65535 0
Calibration Voltage 0x91A6 ADC Gain I2 –32767 32767 0
Calibration Current 0x91A8 CC Gain F4 1.00E–02 10.00E+02 7.4768
Calibration Current 0x91AC Capacity Gain F4 2.98262E+03 4.193046E+08 2230042.463
Calibration Vcell Offset 0x91B0 Vcell Offset I2 –32767 32767 0 mV
Calibration V Divider Offset 0x91B2 Vdiv Offset I2 –32767 32767 0 userV
Calibration Current Offset 0x91C6 Coulomb Counter Offset Samples U2 0 65535 64
Calibration Current Offset 0x91C8 Board Offset I2 –32768 32767 0
Calibration Temperature 0x91CA Internal Temp Offset I1 –128 127 0 0.1°C
Calibration Temperature 0x91CB CFETOFF Temp Offset I1 –128 127 0 0.1°C
Calibration Temperature 0x91CC DFETOFF Temp Offset I1 –128 127 0 0.1°C
Calibration Temperature 0x91CD ALERT Temp Offset I1 –128 127 0 0.1°C
Calibration Temperature 0x91CE TS1 Temp Offset I1 –128 127 0 0.1°C
Calibration Temperature 0x91CF TS2 Temp Offset I1 –128 127 0 0.1°C
Calibration Temperature 0x91D0 TS3 Temp Offset I1 –128 127 0 0.1°C
Calibration Temperature 0x91D1 HDQ Temp Offset I1 –128 127 0 0.1°C
Calibration Temperature 0x91D2 DCHG Temp Offset I1 –128 127 0 0.1°C
Calibration Temperature 0x91D3 DDSG Temp Offset I1 –128 127 0 0.1°C
Calibration Internal Temp Model 0x91E2 Int Gain I2 –32768 32767 25390
Calibration Internal Temp Model 0x91E4 Int base offset I2 –32768 32767 3032
Calibration Internal Temp Model 0x91E6 Int Maximum AD I2 –32768 32767 16383
Calibration Internal Temp Model 0x91E8 Int Maximum Temp I2 0 32767 6379 0.1 K
Calibration 18K Temperature Model 0x91EA Coeff a1 I2 –32768 32767 –15524
Calibration 18K Temperature Model 0x91EC Coeff a2 I2 –32768 32767 26423
Calibration 18K Temperature Model 0x91EE Coeff a3 I2 –32768 32767 –22664
Calibration 18K Temperature Model 0x91F0 Coeff a4 I2 –32768 32767 28834
Calibration 18K Temperature Model 0x91F2 Coeff a5 I2 –32768 32767 672
Calibration 18K Temperature Model 0x91F4 Coeff b1 I2 –32768 32767 –371
Calibration 18K Temperature Model 0x91F6 Coeff b2 I2 –32768 32767 708
Calibration 18K Temperature Model 0x91F8 Coeff b3 I2 –32768 32767 –3498
Calibration 18K Temperature Model 0x91FA Coeff b4 I2 –32768 32767 5051
Calibration 18K Temperature Model 0x91FE Adc0 I2 –32768 32767 11703
Calibration 180K Temperature Model 0x9200 Coeff a1 I2 –32768 32767 –17513
Calibration 180K Temperature Model 0x9202 Coeff a2 I2 –32768 32767 25759
Calibration 180K Temperature Model 0x9204 Coeff a3 I2 –32768 32767 –23593
Calibration 180K Temperature Model 0x9206 Coeff a4 I2 –32768 32767 32175
Calibration 180K Temperature Model 0x9208 Coeff a5 I2 –32768 32767 2090
Calibration 180K Temperature Model 0x920A Coeff b1 I2 –32768 32767 –2055
Calibration 180K Temperature Model 0x920C Coeff b2 I2 –32768 32767 2955
Calibration 180K Temperature Model 0x920E Coeff b3 I2 –32768 32767 –3427
Calibration 180K Temperature Model 0x9210 Coeff b4 I2 –32768 32767 4385
Calibration 180K Temperature Model 0x9214 Adc0 I2 –32768 32767 17246
Calibration Custom Temperature Model 0x9216 Coeff a1 I2 –32768 32767 0
Calibration Custom Temperature Model 0x9218 Coeff a2 I2 –32768 32767 0
Calibration Custom Temperature Model 0x921A Coeff a3 I2 –32768 32767 0
Calibration Custom Temperature Model 0x921C Coeff a4 I2 –32768 32767 0
Calibration Custom Temperature Model 0x921E Coeff a5 I2 –32768 32767 0
Calibration Custom Temperature Model 0x9220 Coeff b1 I2 –32768 32767 0
Calibration Custom Temperature Model 0x9222 Coeff b2 I2 –32768 32767 0
Calibration Custom Temperature Model 0x9224 Coeff b3 I2 –32768 32767 0
Calibration Custom Temperature Model 0x9226 Coeff b4 I2 –32768 32767 0
Calibration Custom Temperature Model 0x9228 Rc0 I2 –32768 32767 0
Calibration Custom Temperature Model 0x922A Adc0 I2 –32768 32767 0
Calibration Current Deadband 0x922D Coulomb Counter Deadband U1 0 255 9 234nV
Calibration CUV 0x91D4 CUV Threshold Override U2 0x0000 0xFFFF 0xFFFF Hex
Calibration COV 0x91D6 COV Threshold Override U2 0x0000 0xFFFF 0xFFFF Hex
Settings Fuse 0x9231 Min Blow Fuse Voltage I2 0 32767 500 10mV
Settings Fuse 0x9233 Fuse Blow Timeout U1 0 255 30 s
Settings Configuration 0x9234 Power Config H2 0x0000 0xFFFF 0x2982 Hex
Settings Configuration 0x9236 REG12 Config H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x9237 REG0 Config H1 0x00 0x03 0x00 Hex
Settings Configuration 0x9238 HWD Regulator Options H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x9239 Comm Type U1 0x00 0x1F 0
Settings Configuration 0x923A I2C Address U1 0x00 0xFF 0
Settings Configuration 0x923C SPI Configuration H1 0x00 0x7F 0x20
Settings Configuration 0x923D Comm Idle Time U1 0 255 0 s
Settings Configuration 0x92FA CFETOFF Pin Config H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x92FB DFETOFF Pin Config H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x92FC ALERT Pin Config H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x92FD TS1 Config H1 0x00 0xFF 0x07 Hex
Settings Configuration 0x92FE TS2 Config H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x92FF TS3 Config H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x9300 HDQ Pin Config H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x9301 DCHG Pin Config H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x9302 DDSG Pin Config H1 0x00 0xFF 0x00 Hex
Settings Configuration 0x9303 DA Configuration H1 0x00 0xFF 0x05 Hex
Settings Configuration 0x9304 Vcell Mode H2 0x0000 0x03FF 0x0000 Hex
Settings Configuration 0x9307 CC3 Samples U1 2 255 80 Num
Settings Protection 0x925F Protection Configuration H2 0x0000 0x07FF 0x0002 Hex
Settings Protection 0x9261 Enabled Protections A U1 0x00 0xFF 0x88 Hex
Settings Protection 0x9262 Enabled Protections B U1 0x00 0xFF 0x00 Hex
Settings Protection 0x9263 Enabled Protections C U1 0x00 0xFF 0x00 Hex
Settings Protection 0x9265 CHG FET Protections A U1 0x00 0xFF 0x98 Hex
Settings Protection 0x9266 CHG FET Protections B U1 0x00 0xFF 0xD5 Hex
Settings Protection 0x9267 CHG FET Protections C U1 0x00 0xFF 0x56 Hex
Settings Protection 0x9269 DSG FET Protections A U1 0x00 0xFF 0xE4 Hex
Settings Protection 0x926A DSG FET Protections B U1 0x00 0xFF 0xE6 Hex
Settings Protection 0x926B DSG FET Protections C U1 0x00 0xFF 0xE2 Hex
Settings Protection 0x9273 Body Diode Threshold I2 0 32767 50 mA
Settings Alarm 0x926D Default Alarm Mask H2 0x0000 0xFFFF 0xF800 Hex
Settings Alarm 0x926F SF Alert Mask A U1 0x00 0xFF 0xFC Hex
Settings Alarm 0x9270 SF Alert Mask B U1 0x00 0xFF 0xF7 Hex
Settings Alarm 0x9271 SF Alert Mask C U1 0x00 0xFF 0xF4 Hex
Settings Alarm 0x92C4 PF Alert Mask A U1 0x00 0xFF 0x5F Hex
Settings Alarm 0x92C5 PF Alert Mask B U1 0x00 0xFF 0x9F Hex
Settings Alarm 0x92C6 PF Alert Mask C U1 0x00 0xFF 0x00 Hex
Settings Alarm 0x92C7 PF Alert Mask D U1 0x00 0xFF 0x00 Hex
Settings Permanent Failure 0x92C0 Enabled PF A U1 0x00 0xFF 0x00 Hex
Settings Permanent Failure 0x92C1 Enabled PF B U1 0x00 0xFF 0x00 Hex
Settings Permanent Failure 0x92C2 Enabled PF C U1 0x00 0xFF 0x07 Hex
Settings Permanent Failure 0x92C3 Enabled PF D U1 0x00 0xFF 0x00 Hex
Settings FET 0x9308 FET Options H1 0x00 0xFF 0x0D Hex
Settings FET 0x9309 Chg Pump Control U1 0x00 0xFF 0x01 Hex
Settings FET 0x930A Precharge Start Voltage I2 0 32767 0 mV
Settings FET 0x930C Precharge Stop Voltage I2 0 32767 0 mV
Settings FET 0x930E Predischarge Timeout U1 0 255 5 10ms
Settings FET 0x930F Predischarge Stop Delta U1 0 255 50 10mV
Settings Current Thresholds 0x9310 Dsg Current Threshold I2 0 32767 100 userA
Settings Current Thresholds 0x9312 Chg Current Threshold I2 0 32767 50 userA
Settings Cell Open-Wire 0x9314 Check Time U1 0 255 5 s
Settings Interconnect Resistances 0x9315 Cell 1 Interconnect I2 0 32767 0
Settings Interconnect Resistances 0x9317 Cell 2 Interconnect I2 0 32767 0
Settings Interconnect Resistances 0x9319 Cell 3 Interconnect I2 0 32767 0
Settings Interconnect Resistances 0x931B Cell 4 Interconnect I2 0 32767 0
Settings Interconnect Resistances 0x931D Cell 5 Interconnect I2 0 32767 0
Settings Interconnect Resistances 0x931F Cell 6 Interconnect I2 0 32767 0
Settings Interconnect Resistances 0x9321 Cell 7 Interconnect I2 0 32767 0
Settings Interconnect Resistances 0x9323 Cell 8 Interconnect I2 0 32767 0
Settings Interconnect Resistances 0x9325 Cell 9 Interconnect I2 0 32767 0
Settings Interconnect Resistances 0x9327 Cell 10 Interconnect I2 0 32767 0
Settings Manufacturing 0x9343 Mfg Status Init H2 0x0000 0xFFFF 0x0040 Hex
Settings Cell Balancing Config 0x9335 Balancing Configuration H1 0x00 0xFF 0x00 Hex
Settings Cell Balancing Config 0x9336 Min Cell Temp I1 –128 127 –20 °C
Settings Cell Balancing Config 0x9337 Max Cell Temp I1 –128 127 60 °C
Settings Cell Balancing Config 0x9338 Max Internal Temp I1 –128 127 70 °C
Settings Cell Balancing Config 0x9339 Cell Balance Interval U1 1 255 20 s
Settings Cell Balancing Config 0x933A Cell Balance Max Cells U1 0 16 1 Num
Settings Cell Balancing Config 0x933B Cell Balance Min Cell V (Charge) I2 0 5000 3900 mV
Settings Cell Balancing Config 0x933D Cell Balance Min Delta (Charge) U1 0 255 40 mV
Settings Cell Balancing Config 0x933E Cell Balance Stop Delta (Charge) U1 0 255 20 mV
Settings Cell Balancing Config 0x933F Cell Balance Min Cell V (Relax) I2 0 5000 3900 mV
Settings Cell Balancing Config 0x9341 Cell Balance Min Delta (Relax) U1 0 255 40 mV
Settings Cell Balancing Config 0x9342 Cell Balance Stop Delta (Relax) U1 0 255 20 mV
Power Shutdown 0x923F Shutdown Cell Voltage I2 0 32767 0 mV
Power Shutdown 0x9241 Shutdown Stack Voltage I2 0 32767 600 10mV
Power Shutdown 0x9243 Low V Shutdown Delay U1 0 63 1 s
Power Shutdown 0x9244 Shutdown Temperature U1 0 150 85 °C
Power Shutdown 0x9245 Shutdown Temperature Delay U1 0 254 5 s
Power Shutdown 0x9252 FET Off Delay U1 0 127 0 0.25s
Power Shutdown 0x9253 Shutdown Command Delay U1 0 254 0 0.25s
Power Shutdown 0x9254 Auto Shutdown Time U1 0 250 0 min
Power Shutdown 0x9255 RAM Fail Shutdown Time U1 0 255 5 s
Power Sleep 0x9248 Sleep Current I2 0 32767 20 mA
Power Sleep 0x924A Voltage Time U1 1 255 5 s
Power Sleep 0x924B Wake Comparator Current I2 500 32767 500 mA
Power Sleep 0x924D Sleep Hysteresis Time U1 0 255 10 s
Power Sleep 0x924E Sleep Charger Voltage Threshold I2 0 32767 2000 10mV
Power Sleep 0x9250 Sleep Charger PACK-TOS Delta I2 10 8500 200 10mV
System Data Integrity 0x91E0 Config RAM Signature U2 0x0000 0x7FFF 0 Hex
Protections CUV 0x9275 Threshold U1 20 90 50 50.6mV
Protections CUV 0x9276 Delay U2 1 2047 74 3.3 ms
Protections CUV 0x927B Recovery Hysteresis U1 2 20 2 50.6mV
Protections COV 0x9278 Threshold U1 20 110 86 50.6mV
Protections COV 0x9279 Delay U2 1 2047 74 3.3 ms
Protections COV 0x927C Recovery Hysteresis U1 2 20 2 50.6mV
Protections COVL 0x927D Latch Limit U1 0 255 0
Protections COVL 0x927E Counter Dec Delay U1 0 255 10 s
Protections COVL 0x927F Recovery Time U1 0 255 15 s
Protections OCC 0x9280 Threshold U1 2 62 2 2mV
Protections OCC 0x9281 Delay U1 1 127 4 3.3 ms
Protections OCC 0x9288 Recovery Threshold I2 –32768 32767 –200 mA
Protections OCC 0x92B0 PACK-TOS Delta I2 10 8500 200 10mV
Protections OCD1 0x9282 Threshold U1 2 100 4 2mV
Protections OCD1 0x9283 Delay U1 1 127 1 3.3 ms
Protections OCD2 0x9284 Threshold U1 2 100 3 2mV
Protections OCD2 0x9285 Delay U1 1 127 7 3.3 ms
Protections SCD 0x9286 Threshold U1 0 15 0
Protections SCD 0x9287 Delay U1 1 31 2 15µs
Protections SCD 0x9294 Recovery Time U1 0 255 5 s
Protections OCD3 0x928A Threshold I2 –32768 0 –4000 userA
Protections OCD3 0x928C Delay U1 0 255 2 s
Protections OCD 0x928D Recovery Threshold I2 –32768 32767 200 mA
Protections OCDL 0x928F Latch Limit U1 0 255 0
Protections OCDL 0x9290 Counter Dec Delay U1 0 255 10 s
Protections OCDL 0x9291 Recovery Time U1 0 255 15 s
Protections OCDL 0x9292 Recovery Threshold I2 –32768 32767 200 mA
Protections SCDL 0x9295 Latch Limit U1 0 255 0
Protections SCDL 0x9296 Counter Dec Delay U1 0 255 10 s
Protections SCDL 0x9297 Recovery Time U1 0 255 15 s
Protections SCDL 0x9298 Recovery Threshold I2 –32768 32767 200 mA
Protections OTC 0x929A Threshold I1 –40 120 55 °C
Protections OTC 0x929B Delay U1 0 255 2 s
Protections OTC 0x929C Recovery I1 –40 120 50 °C
Protections OTD 0x929D Threshold I1 –40 120 60 °C
Protections OTD 0x929E Delay U1 0 255 2 s
Protections OTD 0x929F Recovery I1 –40 120 55 °C
Protections OTF 0x92A0 Threshold U1 0 150 80 °C
Protections OTF 0x92A1 Delay U1 0 255 2 s
Protections OTF 0x92A2 Recovery U1 0 150 65 °C
Protections OTINT 0x92A3 Threshold I1 –40 120 85 °C
Protections OTINT 0x92A4 Delay U1 0 255 2 s
Protections OTINT 0x92A5 Recovery I1 –40 120 80 °C
Protections UTC 0x92A6 Threshold I1 –40 120 0 °C
Protections UTC 0x92A7 Delay U1 0 255 2 s
Protections UTC 0x92A8 Recovery I1 –40 120 5 °C
Protections UTD 0x92A9 Threshold I1 –40 120 0 °C
Protections UTD 0x92AA Delay U1 0 255 2 s
Protections UTD 0x92AB Recovery I1 –40 120 5 °C
Protections UTINT 0x92AC Threshold I1 –40 120 –20 °C
Protections UTINT 0x92AD Delay U1 0 255 2 s
Protections UTINT 0x92AE Recovery I1 –40 120 –15 °C
Protections Recovery 0x92AF Time U1 0 255 3 s
Protections HWD 0x92B2 Delay U2 0 65535 60 s
Protections Load Detect 0x92B4 Active Time U1 0 255 0 s
Protections Load Detect 0x92B5 Retry Delay U1 0 255 50 s
Protections Load Detect 0x92B6 Timeout U2 0 65535 1 hrs
Protections PTO 0x92BA Charge Threshold I2 –32768 32767 250 mA
Protections PTO 0x92BC Delay U2 0 65535 1800 s
Protections PTO 0x92BE Reset I2 0 10000 2 userAh
Permanent Fail CUDEP 0x92C8 Threshold I2 0 32767 1500 mV
Permanent Fail CUDEP 0x92CA Delay U1 0 255 2 s
Permanent Fail SUV 0x92CB Threshold I2 0 32767 2200 mV
Permanent Fail SUV 0x92CD Delay U1 0 255 5 s
Permanent Fail SOV 0x92CE Threshold I2 0 32767 4500 mV
Permanent Fail SOV 0x92D0 Delay U1 0 255 5 s
Permanent Fail TOS 0x92D1 Threshold I2 0 32767 500 mV
Permanent Fail TOS 0x92D3 Delay U1 0 255 5 s
Permanent Fail SOCC 0x92D4 Threshold I2 –32768 32767 10000 userA
Permanent Fail SOCC 0x92D6 Delay U1 0 255 5 s
Permanent Fail SOCD 0x92D7 Threshold I2 –32768 32767 –32000 userA
Permanent Fail SOCD 0x92D9 Delay U1 0 255 5 s
Permanent Fail SOT 0x92DA Threshold I1 –40 120 65 °C
Permanent Fail SOT 0x92DB Delay U1 0 255 5 s
Permanent Fail SOTF 0x92DC Threshold U1 0 150 85 °C
Permanent Fail SOTF 0x92DD Delay U1 0 255 5 s
Permanent Fail VIMR 0x92DE Check Voltage I2 0 5500 3500 mV
Permanent Fail VIMR 0x92E0 Max Relax Current I2 10 32767 10 mA
Permanent Fail VIMR 0x92E2 Threshold I2 0 5500 500 mV
Permanent Fail VIMR 0x92E4 Delay U1 0 255 5 s
Permanent Fail VIMR 0x92E5 Relax Min Duration U2 0 65535 100 s
Permanent Fail VIMA 0x92E7 Check Voltage I2 0 5500 3700 mV
Permanent Fail VIMA 0x92E9 Min Active Current I2 10 32767 50 mA
Permanent Fail VIMA 0x92EB Threshold I2 0 5500 200 mV
Permanent Fail VIMA 0x92ED Delay U1 0 255 5 s
Permanent Fail CFETF 0x92EE OFF Threshold I2 10 5000 20 mA
Permanent Fail CFETF 0x92F0 OFF Delay U1 0 255 5 s
Permanent Fail DFETF 0x92F1 OFF Threshold I2 –5000 –10 –20 mA
Permanent Fail DFETF 0x92F3 OFF Delay U1 0 255 5 s
Permanent Fail VSSF 0x92F4 Fail Threshold I2 1 32767 100
Permanent Fail VSSF 0x92F6 Delay U1 0 255 5 s
Permanent Fail 2LVL 0x92F7 Delay U1 0 255 5 s
Permanent Fail LFOF 0x92F8 Delay U1 0 255 5 s
Permanent Fail HWMX 0x92F9 Delay U1 0 255 5 s
Security Settings 0x9256 Security Settings H1 0x00 0x07 0x00 Hex
Security Keys 0x9257 Unseal Key Step 1 U2 0x0100 0xFFFF 0x0414 Hex
Security Keys 0x9259 Unseal Key Step 2 U2 0x0100 0xFFFF 0x3672 Hex
Security Keys 0x925B Full Access Key Step 1 U2 0x0100 0xFFFF 0xFFFF Hex
Security Keys 0x925D Full Access Key Step 2 U2 0x0100 0xFFFF 0xFFFF Hex