SNOSD10F April   2016  – May 2020

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
    1.     Device Images
      1.      Simplified Block Diagram
      2.      Switching Performance at >100 V/ns
  4. Revision History
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Switching Characteristics
    7. 6.7 Typical Characteristics
  7. Parameter Measurement Information
    1. 7.1 Switching Parameters
      1. 7.1.1 Turn-on Delays
      2. 7.1.2 Turn-off Delays
      3. 7.1.3 Drain Slew Rate
      4. 7.1.4 Turn-on and Turn-off Energy
  8. Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Direct-Drive GaN Architecture
      2. 8.3.2 Internal Buck-Boost DC-DC Converter
      3. 8.3.3 Internal Auxiliary LDO
      4. 8.3.4 Fault Detection
        1. 8.3.4.1 Over-current Protection
        2. 8.3.4.2 Over-Temperature Protection and UVLO
      5. 8.3.5 Drive Strength Adjustment
    4. 8.4 Device Functional Modes
      1. 8.4.1 Low-Power Mode
  9. Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Slew Rate Selection
          1. 9.2.2.1.1 Startup and Slew Rate with Bootstrap High-Side Supply
        2. 9.2.2.2 Signal Level-Shifting
        3. 9.2.2.3 Buck-Boost Converter Design
      3. 9.2.3 Application Curves
    3. 9.3 Paralleling GaN Devices
    4. 9.4 Do's and Don'ts
  10. 10Power Supply Recommendations
    1. 10.1 Using an Isolated Power Supply
    2. 10.2 Using a Bootstrap Diode
      1. 10.2.1 Diode Selection
      2. 10.2.2 Managing the Bootstrap Voltage
      3. 10.2.3 Reliable Bootstrap Start-up
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Power Loop Inductance
      2. 11.1.2 Signal Ground Connection
      3. 11.1.3 Bypass Capacitors
      4. 11.1.4 Switch-Node Capacitance
      5. 11.1.5 Signal Integrity
      6. 11.1.6 High-Voltage Spacing
      7. 11.1.7 Thermal Recommendations
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 Documentation Support
      1. 12.2.1 Related Documentation
    3. 12.3 Receiving Notification of Documentation Updates
    4. 12.4 Community Resources
    5. 12.5 Trademarks
    6. 12.6 Electrostatic Discharge Caution
    7. 12.7 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

Electrical Characteristics

over operating free-air temperature range, 9.5 V < VDD < 18 V, LPM = 5 V, VNEG = -14 V (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
GaN POWER
TRANSISTOR
RDS,ON On-state Resistance TJ = 25°C 70
TJ = 125°C 110
VSD Third-quadrant mode source-drain voltage IN = 0 V, ISD = 0.1 A 5 V
IN = 0 V, ISD = 10 A 7.8
IDSS Drain Leakage Current VDS = 600 V, TJ = 25°C 1 µA
VDS = 600 V, TJ = 125°C 10
Coss GaN output capacitance IN = 0 V, VDS = 400 V, fSW = 250 kHz 71 pF
Coss,er Effective output capacitance, energy related IN = 0 V, VDS =0-400 V 95 pF
Coss,tr Effective output capacitance, time related ID = 5 A, IN = 0 V, VDS = 0-400 V 145 pF
Qrr Reverse recovery charge VR = 400 V, ISD = 5 A, dISD/dt = 1 A/ns 0 nC
DRIVER SUPPLY
IVDD,LPM Quiescent current, ultra-low-power mode VLPM = 0 V, VDD = 12 V 80 95 µA
IVDD,Q Quiescent current (average) Transistor held off 0.5 mA
transistor held on 0.5
IVDD,op Operating current VDD = 12 V, fSW = 1 MHz, RDRV=40 kΩ, 50% duty cycle 43 mA
V+5V 5V LDO output voltage VDD = 12 V 4.7 5.3 V
VNEG Negative Supply 30-mA load current -13.9 V
BUCK BOOST
CONVERTER
fSW,GAN FET switching frequency 1 MHz
IDCDC,PK Peak inductor current IOUT = 20 mA, VIN = 12 V, VOUT = -14 V 250 350 mA
ΔVNEG DC-DC output ripple voltage, pk-pk CNEG = 2.2 µF, IOUT = 20 mA 50 mV
DRIVER INPUT
VIH Input pin, LPM pin, logic high threshold 2.5 V
VIL Input pin, LPM pin, low threshold 0.8 V
VHYST Input pin, LPM pin, hysteresis 0.8 V
RIN,L Input pull-down resistance 150 kΩ
RLPM LPM pin pull-down resistance 150 kΩ
UNDERVOLTAGE LOCKOUT
VDD,(ON) VDD turnon threshold Turn-on voltage 9.1 V
VDD,(OFF) VDD turnoff threshold Turn-off voltage 8.5 V
ΔVDD,UVLO UVLO Hysteresis 550 mV
FAULT
Itrip Current Fault Trip Point
-40℃ ≤ Tj ≤125℃


 
22 36 50 A
Ttrip Temperature Trip Point trip point 165 °C
TtripHys Temperature Trip Hysteresis 20 °C