SBAS940 December   2018 DAC8742H

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
    1.     Device Images
      1.      Simplified Schematic
  4. Revision History
  5. Pin Configuration and Functions
    1.     Pin Functions
  6. Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Typical Characteristics
  7. Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  HART Modulator
      2. 7.3.2  HART Demodulator
      3. 7.3.3  FOUNDATION FIELDBUS / PROFIBUS PA Manchester Encoder
      4. 7.3.4  FOUNDATION FIELDBUS / PROFIBUS PA Manchester Decoder
      5. 7.3.5  Internal Reference
      6. 7.3.6  Clock Configuration
      7. 7.3.7  Reset and Power-Down
      8. 7.3.8  Full-Duplex Mode
      9. 7.3.9  I/O Selection
      10. 7.3.10 Jabber Inhibitor
    4. 7.4 Device Functional Modes
      1. 7.4.1 UART Interfaced HART
      2. 7.4.2 UART Interfaced FOUNDATION FIELDBUS / PROFIBUS PA
      3. 7.4.3 SPI Interfaced HART
      4. 7.4.4 SPI Interfaced FOUNDATION FIELDBUS / PROFIBUS PA
      5. 7.4.5 Interface
        1. 7.4.5.1 UART
          1. 7.4.5.1.1 UART Carrier Detect
        2. 7.4.5.2 SPI
          1. 7.4.5.2.1 SPI Cyclic Redundancy Check
          2. 7.4.5.2.2 SPI Interrupt Request
    5. 7.5 Register Maps
      1. 7.5.1 CONTROL Register (Offset = 2h) [reset = 0x8042]
        1. Table 4. CONTROL Register Field Descriptions
      2. 7.5.2 RESET Register (Offset = 7h) [reset = 0x0000]
        1. Table 5. RESET Register Field Descriptions
      3. 7.5.3 MODEM_STATUS Register (Offset = 20h) [reset = 0x0000]
        1. Table 6. MODEM_STATUS Register Field Descriptions
      4. 7.5.4 MODEM_IRQ_MASK Register (Offset = 21h) [reset = 0x0024]
        1. Table 7. MODEM_IRQ_MASK Register Field Descriptions
      5. 7.5.5 MODEM_CONTROL Register (Offset = 22h) [reset = 0x0048]
        1. Table 8. MODEM_CONTROL Register Field Descriptions
      6. 7.5.6 FIFO_D2M Register (Offset = 23h) [reset = 0x0200]
        1. Table 9. FIFO_D2M Register Field Descriptions
      7. 7.5.7 FIFO_M2D Register (Offset = 24h) [reset = 0x0200]
        1. Table 10. FIFO_M2D Register Field Descriptions
      8. 7.5.8 FIFO_LEVEL_SET Register (Offset = 25h) [reset = 0x0000]
        1. Table 11. FIFO_LEVEL_SET Register Field Descriptions
      9. 7.5.9 PAFF_JABBER Register (Offset = 27h) [reset = 0x0000]
        1. Table 12. PAFF_JABBER Register Field Descriptions
  8. Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1 Design Recommendations
      2. 8.1.2 Selecting the Crystal/Resonator
      3. 8.1.3 Included Functions and Filter Selection
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 DAC8742H HART Modem
        2. 8.2.2.2 2-Wire Current Loop
        3. 8.2.2.3 Regulator
        4. 8.2.2.4 DAC
        5. 8.2.2.5 Amplifiers
        6. 8.2.2.6 Diodes
        7. 8.2.2.7 Passives
      3. 8.2.3 Application Curves
  9. Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Documentation Support
      1. 11.1.1 Related Documentation
    2. 11.2 Receiving Notification of Documentation Updates
    3. 11.3 Community Resources
    4. 11.4 Trademarks
    5. 11.5 Electrostatic Discharge Caution
    6. 11.6 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

MODEM_IRQ_MASK Register (Offset = 21h) [reset = 0x0024]

This register controls which MODEM STATUS events are allowed to trigger an interrupt on the IRQ pin. A 0 in the respective bit position allows the interrupt event to toggle the IRQ pin. A 1 in the respective bit position blocks the interrupt event from toggling the IRQ pin, but the event can still be detected by reading the MODEM STATUS register.

MODEM_IRQ_MASK is shown in Figure 26 and described in Table 7.

Return to Summary Table.

Figure 26. MODEM_IRQ_MASK Register
15 14 13 12 11 10 9 8
RESERVED JAB_OFF JAB_ON GAP FRAME PARITY WDT CRC
R R/W R/W R/W R/W R/W R/W R/W
7 6 5 4 3 2 1 0
FIFO_M2D LEVEL FIFO_M2D FULL FIFO_M2D EMPTY FIFO_D2M LEVEL FIFO_D2M FULL FIFO_D2M EMPTY CD CTS
R/W R/W R/W R/W R/W R/W R/W R/W

Table 7. MODEM_IRQ_MASK Register Field Descriptions

Bit Field Type Reset Description
15 RESERVED R/W 0 Reserved
14 JAB_OFF R/W 0 Writing a 1 to this bit blocks the JAB_OFF event from triggering the IRQ pin
13 JAB_ON R/W 0 Writing a 1 to this bit blocks the JAB_ON event from triggering the IRQ pin
12 GAP R/W 0 Writing a 1 to this bit blocks the GAP event from triggering the IRQ pin
11 FRAME R/W 0 Writing a 1 to this bit blocks the FRAME event from triggering the IRQ pin
10 PARITY R/W 0 Writing a 1 to this bit blocks the PARITY event from triggering the IRQ pin
9 WDT R/W 0 Writing a 1 to this bit blocks the WDT event from triggering the IRQ pin
8 CRC R/W 0 Writing a 1 to this bit blocks the CRC event from triggering the IRQ pin
7 FIFO_M2D_LEVEL R/W 0 Writing a 1 to this bit blocks the FIFO_M2D_LEVEL event from triggering the IRQ pin
6 FIFO_M2D_FULL R/W 0 Writing a 1 to this bit blocks the FIFO_M2D_FULL event from triggering the IRQ pin
5 FIFO_M2D_EMPTY R/W 1 Writing a 1 to this bit blocks the FIFO_M2D_EMPTY event from triggering the IRQ pin
4 FIFO_D2M_LEVEL R/W 0 Writing a 1 to this bit blocks the FIFO_D2M_LEVEL event from triggering the IRQ pin
3 FIFO_D2M_FULL R/W 0 Writing a 1 to this bit blocks the FIFO_D2M_FULL event from triggering the IRQ pin
2 FIFO_D2M_EMPTY R/W 1 Writing a 1 to this bit blocks the FIFO_D2M_EMPTY event from triggering the IRQ pin
1 CD R/W 0 Writing a 1 to this bit blocks the CD event from triggering the IRQ pin
0 CTS R/W 0 Writing a 1 to this bit blocks the CTS event from triggering the IRQ pin