SBOS263H October   2002  – December 2024 OPA830

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configurations
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics for D Package VS = ±5V
    6. 6.6  Electrical Characteristics for D Package VS = 5V
    7. 6.7  Electrical Characteristics for D Package VS = 3V
    8. 6.8  Electrical Characteristics for DBV Package VS = ±5V
    9. 6.9  Electrical Characteristics for DBV Package VS = 5V
    10. 6.10 Electrical Characteristics for DBV Package VS = 3V
    11. 6.11 Typical Characteristics: VS = ±5V
    12. 6.12 Typical Characteristics: VS = ±5V, Differential Configuration
    13. 6.13 Typical Characteristics: VS = 5V
    14. 6.14 Typical Characteristics: VS = 5V, Differential Configuration
    15. 6.15 Typical Characteristics: VS = 3V
    16. 6.16 Typical Characteristics: VS = 3V, Differential Configuration
  8. 7 Parameter Measurement Information
  9. 8 Application and Implementation
    1. 8.1 Application Information
      1. 8.1.1  Wideband Voltage-Feedback Operation
      2. 8.1.2  DC Level-Shifting
      3. 8.1.3  Optimizing Resistor Values
      4. 8.1.4  Bandwidth Versus Gain: Noninverting Operation
      5. 8.1.5  Inverting Amplifier Operation
      6. 8.1.6  Output Current and Voltages
      7. 8.1.7  Driving Capacitive Loads
      8. 8.1.8  Distortion Performance
      9. 8.1.9  Noise Performance
      10. 8.1.10 DC Accuracy and Offset Control
      11. 8.1.11 Thermal Analysis
    2. 8.2 Typical Applications
      1. 8.2.1 Single-Supply ADC Interface
      2. 8.2.2 AC-Coupled Output Video Line Driver
      3. 8.2.3 Noninverting Amplifier With Reduced Peaking
      4. 8.2.4 Single-Supply Active Filter
    3. 8.3 Layout
      1. 8.3.1 Layout Guidelines
        1. 8.3.1.1 Input and ESD Protection
  10. 9 Device and Documentation Support
    1. 9.1 Device Support
      1. 9.1.1 Development Support
        1. 9.1.1.1 Demonstration Boards
        2. 9.1.1.2 Macromodel and Applications Support
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

6.11 Typical Characteristics: VS = ±5V

at TA = 25°C, G = +2, RF = 750Ω, and RL = 150Ω to GND (unless otherwise noted); see also Figure 8-3

OPA830 Noninverting Small-Signal Frequency Response
RL = 150Ω VO = 0.2VPP
Figure 6-1 Noninverting Small-Signal Frequency Response
OPA830 Noninverting Large-Signal Frequency Response
RL = 150Ω G = +2V/V
Figure 6-3 Noninverting Large-Signal Frequency Response
OPA830 Noninverting Pulse Response
G = +2V/V
Figure 6-5 Noninverting Pulse Response
OPA830 Harmonic Distortion vs Load Resistance
f = 5MHz VO = 2VPP G = +2V/V
Figure 6-7 Harmonic Distortion vs Load Resistance
OPA830 Harmonic Distortion vs Output Voltage
f = 5MHz RL = 500Ω G = +2V/V
Figure 6-9 Harmonic Distortion vs Output Voltage
OPA830 Two-Tone, 3rd-Order Intermodulation SpuriousFigure 6-11 Two-Tone, 3rd-Order Intermodulation Spurious
OPA830 Frequency Response vs Capacitive LoadFigure 6-13 Frequency Response vs Capacitive Load
OPA830 Output Voltage Swing vs Output CurrentFigure 6-15 Output Voltage Swing vs Output Current
OPA830 Inverting Small-Signal Frequency Response
RL = 150Ω VO = 0.2VPP
Figure 6-2 Inverting Small-Signal Frequency Response
OPA830 Inverting Large-Signal Frequency Response
RL = 150Ω G = -1V/V
Figure 6-4 Inverting Large-Signal Frequency Response
OPA830 Inverting Pulse Response
G = -1V/V
Figure 6-6 Inverting Pulse Response
OPA830 5MHz Harmonic Distortion vs Supply Voltage
RL = 500Ω VO = 2VPP G = +2V/V
Figure 6-8 5MHz Harmonic Distortion vs Supply Voltage
OPA830 Harmonic Distortion vs Frequency
VO = 2VPP G = +2V/V
Figure 6-10 Harmonic Distortion vs Frequency
OPA830 Supply and Output Current vs TemperatureFigure 6-12 Supply and Output Current vs Temperature
OPA830 Recommended RS vs Capacitive LoadFigure 6-14 Recommended RS vs Capacitive Load
OPA830 Output Voltage and Current LimitationsFigure 6-16 Output Voltage and Current Limitations