SBVS445A October   2024  – December 2024 TPS7N53

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Output Voltage Setting and Regulation
      2. 6.3.2 Low-Noise, Ultra-High Power-Supply Rejection Ratio (PSRR)
      3. 6.3.3 Programmable Soft-Start (SS Pin)
      4. 6.3.4 Precision Enable and UVLO
      5. 6.3.5 Power-Good Pin (PG Pin)
      6. 6.3.6 Active Discharge
      7. 6.3.7 Thermal Shutdown Protection (TSD)
    4. 6.4 Device Functional Modes
      1. 6.4.1 Normal Operation
      2. 6.4.2 Disabled
      3. 6.4.3 Current-Limit Operation
  8. 7 Application and Implementation
    1. 7.1 Application Information
      1. 7.1.1  Precision Enable (External UVLO)
      2. 7.1.2  Input and Output Capacitor Requirements (CIN and COUT)
      3. 7.1.3  Recommended Capacitor Types
      4. 7.1.4  Soft-Start (SS Pin) and Noise Reduction (NR Pin)
      5. 7.1.5  Charge Pump Noise
      6. 7.1.6  Optimizing Noise and PSRR
      7. 7.1.7  Adjustable Operation
      8. 7.1.8  Load Transient Response
      9. 7.1.9  Power-Good Functionality
      10. 7.1.10 Paralleling for Higher Output Current and Lower Noise
      11. 7.1.11 Power Dissipation (PD)
      12. 7.1.12 Estimating Junction Temperature
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Documentation Support
      1. 8.1.1 Related Documentation
    2. 8.2 Receiving Notification of Documentation Updates
    3. 8.3 Support Resources
    4. 8.4 Trademarks
    5. 8.5 Electrostatic Discharge Caution
    6. 8.6 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information
    1. 10.1 Package Option Addendum

7.2.2 Detailed Design Procedure

In this design example, the device is powered by a dc/dc convertor switching at 1 MHz. The load requires a 0.5V clean rail with less than 5μVRMS. A 10μF input capacitor , 22μF output capacitor, 1μF NR capacitor, and 10nF SS capacitor are used to achieve a good balance between fast start-up time and excellent noise, and PSRR performance and load transient.

The output voltage is set using a 3.3kΩ, thin-film resistor value calculated as described in the Output Voltage Setting and Regulation section. The PG can be pulled up to VIN pin using a 10kΩ to provide a Power-Good signal. The enable voltage is provided by a external I/O. Figure 7-10 illustrates that the device meets all design noise requirements. Figure 7-9 depicts adequate PSRR performance..

Figure 7-8 depicts the implementation of these components.