SLVSCJ0F March   2014  – July 2025 TPS25200

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Timing Requirements
    7. 5.7 Typical Characteristics
  7. 6 Parameter Measurement Information
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Enable
      2. 7.3.2 Thermal Sense
      3. 7.3.3 Overcurrent Protection
      4. 7.3.4 FAULT Response
      5. 7.3.5 Output Discharge
    4. 7.4 Device Functional Modes
      1. 7.4.1 Undervoltage Lockout (UVLO)
      2. 7.4.2 Overcurrent Protection (OCP)
      3. 7.4.3 Overvoltage Clamp (OVC)
      4. 7.4.4 Overvoltage Lockout (OVLO)
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Step by Step Design Produce
        2. 8.2.2.2 Input and Output Capacitance
        3. 8.2.2.3 Programming the Current-Limit Threshold
        4. 8.2.2.4 Design Above a Minimum Current Limit
        5. 8.2.2.5 Design Below a Maximum Current Limit
        6. 8.2.2.6 Power Dissipation and Junction Temperature
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 Receiving Notification of Documentation Updates
    3. 9.3 Support Resources
    4. 9.4 Trademarks
    5. 9.5 Electrostatic Discharge Caution
    6. 9.6 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

5.6 Timing Requirements

Conditions are –40°C ≤ TJ ≤ +125°C and 2.5 V ≤ VIN ≤ 6.5 V. VEN = VIN, RILIM = 33 kΩ. Positive current are into terminals. Typical value is at 25°C. All voltages are with respect to GND (unless otherwise noted)
TEST CONDITIONS MIN TYP MAX UNIT
POWER SWITCH
tr OUT voltage rise time CL = 1 µF, RL = 100 Ω, (see Figure 6-2) 2.05 3.2 ms
tf OUT voltage fall time 0.18 0.2
ENABLE INPUT EN
ton Turnon time 2.5 V ≤ VIN ≤ 5 V, CL = 1 µF, RL = 100 Ω, (see Figure 6-2) 5.12 7.3 ms
toff Turnoff time 0.22 0.3 ms
CURRENT LIMIT
t(IOS) Short-circuit response time VIN = 5 V (see Figure 6-4) 3.5(1) µs
OVERVOLTAGE LOCKOUT, IN
t(OVLO_off_delay) Turnoff delay for OVLO VIN 5 V to 10 V with 1-V/µs ramp up rate, VOUT with 100-Ω load 0.6(1) µs
FAULT FLAG
FAULT deglitch FAULT assertion or de-assertion due to overcurrent condition 5 8 12 ms
(1) This parameter is provided for reference only and does not constitute part of TI's published device specifications for purposes of TI's product warranty.