SLVSDO6D August   2017  – December 2024 TPS1H000-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Pin Configuration and Functions
  6. 5 Specifications
    1. 5.1 Absolute Maximum Ratings
    2. 5.2 ESD Ratings
    3. 5.3 Recommended Operating Conditions
    4. 5.4 Thermal Information
    5. 5.5 Electrical Characteristics
    6. 5.6 Switching Characteristics
    7. 5.7 Typical Characteristics
  7. 6 Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Current Limit
      2. 6.3.2 DELAY Pin Configuration
        1. 6.3.2.1 Holding Mode
        2. 6.3.2.2 Latch-Off Mode
        3. 6.3.2.3 Auto-Retry Mode
      3. 6.3.3 Standalone Operation
      4. 6.3.4 Fault Truth Table
      5. 6.3.5 Full Diagnostics
        1. 6.3.5.1 Short-to-GND and Overload Detection
        2. 6.3.5.2 Open-Load Detection
          1. 6.3.5.2.1 Output On
          2. 6.3.5.2.2 Output Off
        3. 6.3.5.3 Short-to-Battery Detection
        4. 6.3.5.4 Thermal Fault Detection
          1. 6.3.5.4.1 Thermal Shutdown
          2. 6.3.5.4.2 Thermal Swing
          3. 6.3.5.4.3 Fault Report Holding
      6. 6.3.6 Full Protections
        1. 6.3.6.1 UVLO Protection
        2. 6.3.6.2 Inductive Load Switching Off Clamp
        3. 6.3.6.3 Loss-of-GND Protection
        4. 6.3.6.4 Loss-of-Power-Supply Protection
        5. 6.3.6.5 Reverse-Current Protection
        6. 6.3.6.6 MCU I/O Protection
    4. 6.4 Device Functional Modes
      1. 6.4.1 Working Modes
        1. 6.4.1.1 Normal Mode
        2. 6.4.1.2 Standby Mode
        3. 6.4.1.3 Standby Mode With Diagnostics
  8. 7 Application and Implementation
    1. 7.1 Application Information
    2. 7.2 Typical Application
      1. 7.2.1 Design Requirements
      2. 7.2.2 Detailed Design Procedure
      3. 7.2.3 Application Curves
    3. 7.3 Power Supply Recommendations
    4. 7.4 Layout
      1. 7.4.1 Layout Guidelines
      2. 7.4.2 Layout Example
  9. 8 Device and Documentation Support
    1. 8.1 Receiving Notification of Documentation Updates
    2. 8.2 Support Resources
    3. 8.3 Trademarks
    4. 8.4 Electrostatic Discharge Caution
    5. 8.5 Glossary
  10. 9 Revision History
  11. 10Mechanical, Packaging, and Orderable Information

6.3.6.2 Inductive Load Switching Off Clamp

When switching an inductive load off, the inductive reactance tends to pull the output voltage negative. Excessive negative voltage could cause the power FET to break down. To protect the power FET, an internal clamp between drain and source is implemented, namely VDS(clamp).

TPS1H000-Q1 Drain-to-Source Clamping StructureFigure 6-14 Drain-to-Source Clamping Structure
TPS1H000-Q1 Inductive-Load Switching-Off DiagramFigure 6-15 Inductive-Load Switching-Off Diagram