SPRUJG2A December   2024  – September 2026

 

  1.   1
  2.   Description
  3.   Get Started
  4.   Features
  5.   5
  6. 1Evaluation Module Overview
    1. 1.1 Introduction
    2. 1.2 Kit Contents
    3. 1.3 Specification
    4. 1.4 Device Information
    5. 1.5 EVM Revisions and Assembly Variants
  7. 2Hardware
    1. 2.1  Additional Images
    2. 2.2  Key Features
      1. 2.2.1 Processor
      2. 2.2.2 Power Supply
      3. 2.2.3 Memory
      4. 2.2.4 JTAG/Emulator
      5. 2.2.5 Supported Interfaces and Peripherals
      6. 2.2.6 Expansion Connectors/Headers to Support Application Specific Add‐On Boards
    3. 2.3  Power Requirements
    4. 2.4  Setup and Configuration
      1. 2.4.1 EVM DIP Switches
      2. 2.4.2 Boot Modes
      3. 2.4.3 User Test LEDs
    5. 2.5  Power ON/OFF Procedures
      1. 2.5.1 Power ON Procedure
      2. 2.5.2 Power OFF Procedure
      3. 2.5.3 Power Test Points
      4. 2.5.4 Power Indication LED
    6. 2.6  Interfaces
      1. 2.6.1  AM62D Audio EVM Interface Mapping
      2. 2.6.2  Audio Interface
        1. 2.6.2.1 Audio Stereo Lineouts
        2. 2.6.2.2 Audio Microphone and Line In
      3. 2.6.3  JTAG Interface
      4. 2.6.4  UART Interface
      5. 2.6.5  USB Interface
        1. 2.6.5.1 USB2.0 Type-A Interface
        2. 2.6.5.2 USB2.0 Type-C Interface
      6. 2.6.6  MCAN Interface
      7. 2.6.7  Memory Interfaces
        1. 2.6.7.1 LPDDR4 Interface
        2. 2.6.7.2 Octal Serial Peripheral Interface (OSPI)
        3. 2.6.7.3 MMC Interfaces
          1. 2.6.7.3.1 MMC0 - eMMC Interface
          2. 2.6.7.3.2 MMC1 - MicroSD Interface
        4. 2.6.7.4 Board ID EEPROM
      8. 2.6.8  Ethernet Interface
      9. 2.6.9  CPSW Ethernet 1 and CPSW Ethernet 2
      10. 2.6.10 GPIO Port Expander
      11. 2.6.11 GPIO Mapping
    7. 2.7  Power
      1. 2.7.1 Power Input
      2. 2.7.2 Power Supply
      3. 2.7.3 Power Sequencing
      4. 2.7.4 AM62D SOC Power
      5. 2.7.5 Current Monitoring
    8. 2.8  Clocking
      1. 2.8.1 Peripheral Ref Clock
    9. 2.9  Reset
    10. 2.10 CPLD Mapping
    11. 2.11 Audio Expansion Connectors (Headers)
      1. 2.11.1 Audio Expansion Connector 1
      2. 2.11.2 Audio Expansion Connector 2
    12. 2.12 Interrupt
    13. 2.13 I2C Address Mapping
  8. 3Hardware Design Files
  9. 4Compliance Information
    1. 4.1 Compliance and Certifications
  10. 5Additional Information
    1. 5.1 Known Hardware or Software Issues
      1. 5.1.1 Issue 1 - CPLD C4 Version Unavailable
      2. 5.1.2 Issue 2 - RGMII Boot Failure
    2. 5.2 Trademarks
  11. 6Related Documentation
  12. 7References
  13. 8Revision History

2.6.1 AM62D Audio EVM Interface Mapping

Table 2-12 Interface Mapping
Interface Name Port on SoC Device Part Number
Memory – LPDDR4 DDR0 MT53E1G32D2FW-046 IT:C
Memory – OSPI OSPI0 S28HS512TGABHM010
Memory – MicroSD Socket MMC1 MEM2052-00-195-00-A
Memory – eMMC MMC0 MTFC32GBCAQTC
Memory – Board ID EEPROM SoC_I2C0 AT24C512C-MAHM-T
Ethernet Expansion Connector CPSW 1 SoC_RGMII1 DF40GB-48DP-0.4V
Ethernet Expansion Connector CPSW 2 SoC_RGMII2 DF40GB-48DP-0.4V
GPIO Port Expander1 SoC_I2C0 TCA6424ARGJR
Audio Expansion Connector 1 SPI0, SPI2, UART5, SoC_I2C2, McASP1, McASP0 and GPIOs QSE-040-01-L-D-A-K
Audio Expansion Connector 2 SPI0, SPI1, UART6, SoC_I2C1, McASP2 and GPIOs QSE-040-01-L-D-A-K
USB2.0 Type-C USB0 2012670005
USB2.0 Type-A USB1 629104151021
On-board Audio MIC / Line IN McASP2_ACLKR, McASP2_AFSR andSoC_I2C PCM6240QRTVRQ1 and STX-4235
On-board Audio Stereo Line OUT McASP2_ACLKX,McASP2_AFSX andSoC_I2C0 TAD5212IRGER and STX-4235
GPIO Port Expander2 SoC_I2C0 TCA6416ARTWR
MCAN header - 1x3 HDR MCU_MCAN0, MCAN0
UART Terminal (UART-to-USB) SoC_UAR SoC_UART4, WKUP_UART0, CPLD_UART0 and MCU_UART0 FT4232HL and 629105150521
Temperature Sensors SoC_I2C0 TMP100NA/3K
Current Monitors SoC_I2C0 INA228AIDGSR