Home Power management Multi-channel ICs (PMICs)
Home
Power management
Multi-channel ICs (PMICs)

TPS659128

ACTIVE

PMU for processor power

Order now
Data sheet

TPS659128

ACTIVE
Data sheet Order now

Product details

Processor supplier Generic Processor name Generic Product type Processor and FPGA Regulated outputs (#) 14 Step-down DC/DC converter 4 Step-up DC/DC converter 0 LDO 10 Vin (min) (V) 0.8 Vin (max) (V) 5.5 Vout (min) (V) 0.5 Vout (max) (V) 3.8 Iout (max) (A) 2.5 Configurability Factory programmable Features Comm control, Dynamic voltage scaling, Eco-mode, Overcurrent protection, Power sequencing, Thermal shutdown, UVLO fixed Rating Catalog Operating temperature range (°C) -40 to 105 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.008 Switching frequency (max) (kHz) 2800 Shutdown current (ISD) (typ) (µA) 3 Switching frequency (typ) (kHz) 2800
Processor supplier Generic Processor name Generic Product type Processor and FPGA Regulated outputs (#) 14 Step-down DC/DC converter 4 Step-up DC/DC converter 0 LDO 10 Vin (min) (V) 0.8 Vin (max) (V) 5.5 Vout (min) (V) 0.5 Vout (max) (V) 3.8 Iout (max) (A) 2.5 Configurability Factory programmable Features Comm control, Dynamic voltage scaling, Eco-mode, Overcurrent protection, Power sequencing, Thermal shutdown, UVLO fixed Rating Catalog Operating temperature range (°C) -40 to 105 Step-down DC/DC controller 0 Step-up DC/DC controller 0 Iq (typ) (mA) 0.008 Switching frequency (max) (kHz) 2800 Shutdown current (ISD) (typ) (µA) 3 Switching frequency (typ) (kHz) 2800
DSBGA (YFF) 81 16 mm² 4 x 4
  • Four step-down converters:
    • Input voltage (VIN) range from 2.7 V to 5.5 V
    • Power save mode at light load current
    • Output voltage accuracy in PWM mode ±2%
    • Typical 26-µA quiescent current per converter
    • Dynamic voltage scaling
    • 100% duty cycle for lowest dropout
  • Ten LDOs:
    • 8 general-purpose LDOs
    • Output voltage range from 0.8 V to 3.3 V
    • Typical 32-µA quiescent current per LDO
    • 2 low-noise RF-LDOs
    • Output voltage range from 1.6 V to 3.3 V
    • Preregulation support by separate power inputs
    • Eco-mode™ control scheme
    • VIN range of LDOs respective to the following voltage ranges:
      • 1.8 V to 3.6 V
      • 3 V to 5.5 V
  • Three LED drivers:
    • Internal dimming using I2C
    • Up to 20 mA per current sink
  • Thermal monitoring
    • High temperature warning
    • Thermal shutdown
  • Bypass switch
    • Used with DCDC4 in applications powering a Radio Frequency Power Amplifier (RF-PA)
  • Interface
    • I2C interface
    • Power I2C interface for Dynamic Voltage Scaling (DVS)
    • Serial Peripheral Interface (SPI)
  • 32-kHz RC oscillator
  • Undervoltage lockout, battery fault comparator, and long button-press detection
  • 3.6-mm × 3.6-mm DSBGA package with 0.4-mm pitch
  • Four step-down converters:
    • Input voltage (VIN) range from 2.7 V to 5.5 V
    • Power save mode at light load current
    • Output voltage accuracy in PWM mode ±2%
    • Typical 26-µA quiescent current per converter
    • Dynamic voltage scaling
    • 100% duty cycle for lowest dropout
  • Ten LDOs:
    • 8 general-purpose LDOs
    • Output voltage range from 0.8 V to 3.3 V
    • Typical 32-µA quiescent current per LDO
    • 2 low-noise RF-LDOs
    • Output voltage range from 1.6 V to 3.3 V
    • Preregulation support by separate power inputs
    • Eco-mode™ control scheme
    • VIN range of LDOs respective to the following voltage ranges:
      • 1.8 V to 3.6 V
      • 3 V to 5.5 V
  • Three LED drivers:
    • Internal dimming using I2C
    • Up to 20 mA per current sink
  • Thermal monitoring
    • High temperature warning
    • Thermal shutdown
  • Bypass switch
    • Used with DCDC4 in applications powering a Radio Frequency Power Amplifier (RF-PA)
  • Interface
    • I2C interface
    • Power I2C interface for Dynamic Voltage Scaling (DVS)
    • Serial Peripheral Interface (SPI)
  • 32-kHz RC oscillator
  • Undervoltage lockout, battery fault comparator, and long button-press detection
  • 3.6-mm × 3.6-mm DSBGA package with 0.4-mm pitch

The TPS659128x device provides four configurable step-down converters with up to 2.5-A output current and ten LDO regulators for external use. These LDOs can be supplied from either a battery or a preregulated supply. Each specific part number has a different factory programmed power-up and power-down sequence.

The TPS659128x device integrates a 32-kHz RC oscillator to sequence all resources during power up or power down. All LDOs and DC-DC converters can be controlled by an I2C or SPI interface or basic enable pins after boot. Additionally, a voltage-scaling interface allows for transitioning the DC-DC converters to a different voltage through I2C or basic roof-floor control. Three LED drivers with an advanced dimming feature are integrated inside the device. General-purpose input-output (GPIO) functionality is multiplexed with various pins, including LED pins, ENx pins, and SPI pins when not used. Each GPIO can be configured as part of the power-up sequence to control external resources. One SLEEP pin enables switching between the active mode and preprogrammed sleep mode for power optimization. The TPS659128x device comes in a 9-pin × 9-pin DSBGA package (3.6 mm × 3.6 mm) with a 0.4-mm pitch.

The TPS659128x device provides four configurable step-down converters with up to 2.5-A output current and ten LDO regulators for external use. These LDOs can be supplied from either a battery or a preregulated supply. Each specific part number has a different factory programmed power-up and power-down sequence.

The TPS659128x device integrates a 32-kHz RC oscillator to sequence all resources during power up or power down. All LDOs and DC-DC converters can be controlled by an I2C or SPI interface or basic enable pins after boot. Additionally, a voltage-scaling interface allows for transitioning the DC-DC converters to a different voltage through I2C or basic roof-floor control. Three LED drivers with an advanced dimming feature are integrated inside the device. General-purpose input-output (GPIO) functionality is multiplexed with various pins, including LED pins, ENx pins, and SPI pins when not used. Each GPIO can be configured as part of the power-up sequence to control external resources. One SLEEP pin enables switching between the active mode and preprogrammed sleep mode for power optimization. The TPS659128x device comes in a 9-pin × 9-pin DSBGA package (3.6 mm × 3.6 mm) with a 0.4-mm pitch.
filter Find other Multi-channel ICs (PMICs)
Download View video with transcript Video

Similar products you might be interested in

open-in-new Compare alternates
Similar functionality to the compared device
LP8758-EA ACTIVE Four, single-phase 4-A output DC-DC step-down converter Similar functionality and pre-programmed to power the same application processor.

Technical documentation

star =Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 1
Top documentation Type Title Format options Date
* Data sheet TPS659128 PMU for Processor Power datasheet (Rev. A) 10 Jun 2021

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Driver or library

TPS65912SW-LINUX — Linux Driver for TPS65912

The Linux driver supports the TPS65912 Video ADC. The Linux driver supports communication through the I2C and SPI bus and interfaces with the Regulator sub-system.

Linux Mainline Status

Available in Linux Main line: Yes
Available through git.ti.com: N/A

Supported Devices:

  • tps65912

 

Linux Source Files

The (...)

View Options
GUI for evaluation module (EVM)

IPG-UI — IPG-UI EVM GUI (Windows Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

Supported products & hardware

Supported products & hardware
Download
GUI for evaluation module (EVM)

IPG-UI-LINUX — IPG-UI EVM GUI (Linux Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

Supported products & hardware

Supported products & hardware
Download
GUI for evaluation module (EVM)

IPG-UI-OSX — IPG-UI EVM GUI (OSX Installer)

The IPG-UI GUI can be used to configure multiple PMIC devices to evaluate the features and performance of those devices.  This GUI is built using web-based technologies and supports interacting with the EVM hardware using a USB2ANY adapter board. The USB2ANY Explorer is provided to allow (...)

Supported products & hardware

Supported products & hardware
Download
GUI for evaluation module (EVM)

SLVC435 — TPS65912xEVM Software – Legacy

Supported products & hardware

Supported products & hardware
Download
Package Pins CAD symbols, footprints & 3D models
DSBGA (YFF) 81 Ultra Librarian
TI's Standard Terms and Conditions for Evaluation Items apply.

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring
Information included:
  • Fab location
  • Assembly location

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E™ forums with technical support from TI engineers

View all forum topics

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos