JAJSRL6 November   2023 AFE432A3W , AFE532A3W

PRODUCTION DATA  

  1.   1
  2. 特長
  3. アプリケーション
  4. 概要
  5. Pin Configuration and Functions
  6. Specifications
    1. 5.1  Absolute Maximum Ratings
    2. 5.2  ESD Ratings
    3. 5.3  Recommended Operating Conditions
    4. 5.4  Thermal Information
    5. 5.5  Electrical Characteristics: Voltage Output
    6. 5.6  Electrical Characteristics: Current Output
    7. 5.7  Electrical Characteristics: Comparator Mode
    8. 5.8  Electrical Characteristics: ADC Input
    9. 5.9  Electrical Characteristics: General
    10. 5.10 Timing Requirements: I2C Standard Mode
    11. 5.11 Timing Requirements: I2C Fast Mode
    12. 5.12 Timing Requirements: I2C Fast-Mode Plus
    13. 5.13 Timing Requirements: SPI Write Operation
    14. 5.14 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 0)
    15. 5.15 Timing Requirements: SPI Read and Daisy Chain Operation (FSDO = 1)
    16. 5.16 Timing Requirements: GPIO
    17. 5.17 Timing Diagrams
    18. 5.18 Typical Characteristics: Voltage Output
    19. 5.19 Typical Characteristics: Current Output
    20. 5.20 Typical Characteristics: Comparator
    21. 5.21 Typical Characteristics: ADC
    22. 5.22 Typical Characteristics: General
  7. Detailed Description
    1. 6.1 Overview
    2. 6.2 Functional Block Diagram
    3. 6.3 Feature Description
      1. 6.3.1 Smart Analog Front End (AFE) Architecture
      2. 6.3.2 Digital Input/Output
      3. 6.3.3 Nonvolatile Memory (NVM)
    4. 6.4 Device Functional Modes
      1. 6.4.1 Voltage-Output Mode
        1. 6.4.1.1 Voltage Reference and DAC Transfer Function
          1. 6.4.1.1.1 Internal Reference
          2. 6.4.1.1.2 Power-Supply as Reference
      2. 6.4.2 Current-Output Mode
      3. 6.4.3 Comparator Mode
        1. 6.4.3.1 Programmable Hysteresis Comparator
        2. 6.4.3.2 Programmable Window Comparator
      4. 6.4.4 Analog-to-Digital Converter (ADC) Mode
      5. 6.4.5 Fault-Dump Mode
      6. 6.4.6 Application-Specific Modes
        1. 6.4.6.1 Voltage Margining and Scaling
          1. 6.4.6.1.1 High-Impedance Output and PROTECT Input
          2. 6.4.6.1.2 Programmable Slew-Rate Control
        2. 6.4.6.2 Function Generation
          1. 6.4.6.2.1 Triangular Waveform Generation
          2. 6.4.6.2.2 Sawtooth Waveform Generation
          3. 6.4.6.2.3 Sine Waveform Generation
      7. 6.4.7 Device Reset and Fault Management
        1. 6.4.7.1 Power-On Reset (POR)
        2. 6.4.7.2 External Reset
        3. 6.4.7.3 Register-Map Lock
        4. 6.4.7.4 NVM Cyclic Redundancy Check (CRC)
          1. 6.4.7.4.1 NVM-CRC-FAIL-USER Bit
          2. 6.4.7.4.2 NVM-CRC-FAIL-INT Bit
      8. 6.4.8 General-Purpose Input/Output (GPIO) Modes
    5. 6.5 Programming
      1. 6.5.1 SPI Programming Mode
      2. 6.5.2 I2C Programming Mode
        1. 6.5.2.1 F/S Mode Protocol
        2. 6.5.2.2 I2C Update Sequence
          1. 6.5.2.2.1 Address Byte
          2. 6.5.2.2.2 Command Byte
        3. 6.5.2.3 I2C Read Sequence
  8. Register Map
    1. 7.1  NOP Register (address = 00h) [reset = 0000h]
    2. 7.2  DAC-0-MARGIN-HIGH Register (address = 0Dh) [reset = 0000h]
    3. 7.3  DAC-1-MARGIN-HIGH Register (address = 13h) [reset = 0000h]
    4. 7.4  DAC-2-MARGIN-HIGH Register (address = 01h) [reset = 0000h]
    5. 7.5  DAC-0-MARGIN-LOW Register (address = 0Eh) [reset = 0000h]
    6. 7.6  DAC-1-MARGIN-LOW Register (address = 14h) [reset = 0000h]
    7. 7.7  DAC-2-MARGIN-LOW Register (address = 02h) [reset = 0000h]
    8. 7.8  DAC-0-GAIN-CONFIG Register (address = 0Fh) [reset = 0000h]
    9. 7.9  DAC-1-GAIN-CMP-CONFIG Register (address = 15h) [reset = 0000h]
    10. 7.10 DAC-2-GAIN-CONFIG Register (address = 03h) [reset = 0000h]
    11. 7.11 DAC-1-CMP-MODE-CONFIG Register (address = 17h) [reset = 0000h]
    12. 7.12 DAC-0-FUNC-CONFIG Register (address = 12h) [reset = 0000h]
    13. 7.13 DAC-1-FUNC-CONFIG Register (address = 18h) [reset = 0000h]
    14. 7.14 DAC-2-FUNC-CONFIG Register (address = 06h) [reset = 0000h]
    15. 7.15 DAC-0-DATA Register (address = 1Bh) [reset = 0000h]
    16. 7.16 DAC-1-DATA Register (address = 1Ch) [reset = 0000h]
    17. 7.17 DAC-2-DATA Register (address = 19h) [reset = 0000h]
    18. 7.18 ADC-CONFIG-TRIG Register (address = 1Dh) [reset = 0000h]
    19. 7.19 ADC-DATA Register (address = 1Eh) [reset = 0001h]
    20. 7.20 COMMON-CONFIG Register (address = 1Fh) [reset = 0FFFh]
    21. 7.21 COMMON-TRIGGER Register (address = 20h) [reset = 0000h]
    22. 7.22 COMMON-DAC-TRIG Register (address = 21h) [reset = 0000h]
    23. 7.23 GENERAL-STATUS Register (address = 22h) [reset = 20h, DEVICE-ID, VERSION-ID]
    24. 7.24 CMP-STATUS Register (address = 23h) [reset = 000Ch]
    25. 7.25 GPIO-CONFIG Register (address = 24h) [reset = 0000h]
    26. 7.26 DEVICE-MODE-CONFIG Register (address = 25h) [reset = 0000h]
    27. 7.27 INTERFACE-CONFIG Register (address = 26h) [reset = 0000h]
    28. 7.28 SRAM-CONFIG Register (address = 2Bh) [reset = 0000h]
    29. 7.29 SRAM-DATA Register (address = 2Ch) [reset = 0000h]
    30. 7.30 BRDCAST-DATA Register (address = 50h) [reset = 0000h]
  9. Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. Device and Documentation Support
    1. 9.1 Documentation Support
      1. 9.1.1 Related Documentation
    2. 9.2 ドキュメントの更新通知を受け取る方法
    3. 9.3 サポート・リソース
    4. 9.4 Trademarks
    5. 9.5 静電気放電に関する注意事項
    6. 9.6 用語集
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Comparator Mode

DAC channel 1 can be configured as programmable comparator in the voltage-output mode. To enter the comparator mode for channel 1, write 1 to the CMP-1-EN bit in DAC-1-GAIN-CMP-CONFIG register. The comparator output can be configured as push-pull or open-drain using the CMP-1-OD-EN bit. To enable the comparator output on the output pin, write 1 to the CMP-1-OUT-EN bit. To invert the comparator output, write 1 to the CMP-1-INV-EN bit. The FB1 pin has a finite impedance. By default, the FB1 pin is in the high-impedance mode. To disable high-impedance on the FB1 pin, write 1 to the CMP-1-HIZ-IN-DIS bit. Table 6-1 shows the comparator output at the pin for different bit settings. The output of the comparator is indicated by the CMP-FLAG-1 bit in the CMP-STATUS register.

Note: In the Hi-Z input mode, the comparator input range is limited to:
  • For GAIN = 1 ×, 1.5 ×, or 2 ×: VFB1 ≤ (VREF × GAIN) / 3
  • For GAIN = 3 ×, or 4 ×: VFB1 ≤ (VREF × GAIN) / 6
Any higher input voltage is clipped.
Table 6-1 Comparator Output Configuration
CMP-1-EN CMP-1-OUT-EN CMP-1-OD-EN CMP-1-INV-EN CMPX-OUT PIN
0 X X X Comparator not enabled
1 0 X X No output
1 1 0 0 Push-pull output
1 1 0 1 Push-pull and inverted output
1 1 1 0 Open-drain output
1 1 1 1 Open-drain and inverted output

Figure 6-2 shows the interface circuit when DAC channel 1 is configured as a comparator. The programmable comparator operation is as shown in Figure 6-3. The comparator can be configured in no-hysteresis, with-hysteresis, and window-comparator modes using the CMP-1-MODE bit in the respective DAC-1-CMP-MODE-CONFIG register, as shown in Table 6-2.

GUID-20231030-SS0I-PTSC-M9PP-CS4DNZN5FG4Z-low.svg Figure 6-2 Comparator Interface
GUID-20231030-SS0I-KSM9-1JRQ-3890WNXMJRZT-low.svg Figure 6-3 Programmable Comparator Operation
Table 6-2 Comparator Mode Selection
CMP-1-MODE BIT FIELD COMPARATOR CONFIGURATION
00 Normal comparator mode. No hysteresis or window operation.
01 Hysteresis comparator mode. DAC-1-MARGIN-HIGH and DAC-1-MARGIN-LOW registers set the hysteresis.
10 Window comparator mode. DAC-1-MARGIN-HIGH and DAC-1-MARGIN-LOW registers set the window bounds.
11 Invalid setting