JAJSFB3 April   2018 LM25119Q

PRODUCTION DATA.  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
    1.     Device Images
      1.      代表的なアプリケーション回路
  4. 4 改訂履歴
  5. 5 概要（続き）
  6. 6 Pin Configuration and Functions
    1.     Pin Functions
  7. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Switching Characteristics
    7. 7.7 Typical Characteristics
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  High Voltage Start-Up Regulator
      2. 8.3.2  UVLO
      3. 8.3.3  Enable 2
      4. 8.3.4  Oscillator and Sync Capability
      5. 8.3.5  Error Amplifiers and PWM Comparators
      6. 8.3.6  Ramp Generator
      7. 8.3.7  Current Limit
      8. 8.3.8  Hiccup Mode Current Limiting
      9. 8.3.9  Soft Start
      10. 8.3.10 HO and LO Output Drivers
      11. 8.3.11 Maximum Duty Cycle
      12. 8.3.12 Thermal Protection
    4. 8.4 Device Functional Modes
      1. 8.4.1 Diode Emulation
  9. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Miscellaneous Functions
      2. 9.1.2 Interleaved Two-Phase Operation
      3. 9.1.3 Interleaved 4-Phase Operation
    2. 9.2 Typical Applications
      1. 9.2.1 Dual-output Design Example
        1. 9.2.1.1 Design Requirements
          1. 9.2.1.1.1 External Components
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1  Timing Resistor
          2. 9.2.1.2.2  Output Inductor
          3. 9.2.1.2.3  Current Sense Resistor
          4. 9.2.1.2.4  Ramp Resistor and Ramp Capacitor
          5. 9.2.1.2.5  Output Capacitors
          6. 9.2.1.2.6  Input Capacitors
          7. 9.2.1.2.7  VCC Capacitor
          8. 9.2.1.2.8  Bootstrap Capacitor
          9. 9.2.1.2.9  Soft Start Capacitor
          10. 9.2.1.2.10 Restart Capacitor
          11. 9.2.1.2.11 Output Voltage Divider
          12. 9.2.1.2.12 UVLO Divider
          13. 9.2.1.2.13 MOSFET Selection
          14. 9.2.1.2.14 MOSFET Snubber
          15. 9.2.1.2.15 Error Amplifier Compensation
        3. 9.2.1.3 Application Curves
      2. 9.2.2 Two-Phase Design Example
        1. 9.2.2.1 Design Requirements
        2. 9.2.2.2 Detailed Design Procedure
        3. 9.2.2.3 Application Curves
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
      1. 11.1.1 Switching Jitter Root Causes and Solutions
    2. 11.2 Layout Example
  12. 12デバイスおよびドキュメントのサポート
    1. 12.1 コミュニティ・リソース
    2. 12.2 商標
    3. 12.3 静電気放電に関する注意事項
    4. 12.4 Glossary
  13. 13メカニカル、パッケージ、および注文情報

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

9.2.1.2.6 Input Capacitors

The regulator input supply voltage typically has high source impedance at the switching frequency. Good-quality input capacitors are necessary to limit the ripple voltage at the VIN pin while supplying most of the switch current during the ON-time. When the buck switch turns on, the current into the buck switch steps to the valley of the inductor current waveform, ramps up to the peak value, and then drops to the zero at turnoff. The input capacitance must be selected for RMS current rating and minimum ripple voltage. A good approximation for the required ripple current rating necessary is IRMS > IOUT / 2. Seven 2.2-μF ceramic capacitors were used for each channel. With ceramic capacitors, the input ripple voltage is triangular. The input ripple voltage with one channel operating is approximately Equation 24 and the example (Equation 25).

Equation 24. LM25119Q 30126244.gif
Equation 25. LM25119Q 30126245.gif

The ripple voltage of the input capacitors is reduced significantly with dual-channel operation because each channel operates 180 degrees out of phase from the other. Capacitors connected in parallel must be evaluated for RMS current rating. The current splits between the input capacitors based on the relative impedance of the capacitors at the switching frequency.

When the converter is connected to an input power source, a resonant circuit is formed by the line inductance and the input capacitors. To minimize overshoot make CIN > 10 x LIN. The characteristic source impedance (ZS) and resonant frequency (fS) are Equation 26 and the example (Equation 27).

Equation 26. LM25119Q 30126246.gif

where

  • LIN is the inductance of the input wire
Equation 27. LM25119Q 30126247.gif

The converter exhibits negative input impedance which is lowest at the minimum input voltage in Equation 28.

Equation 28. LM25119Q 30126248.gif

The damping factor for the input filter is given by Equation 29.

Equation 29. LM25119Q 30126249.gif

where

  • RIN is the input wiring resistance
  • ESR is the equivalent series resistance of the input capacitors

When δ = 1, the input filter is critically damped. This may be difficult to achieve with practical component values. With δ < 0.2, the input filter exhibits significant ringing. If δ is zero or negative, there is not enough resistance in the circuit and the input filter sustains an oscillation. When operating near the minimum input voltage, a bulk aluminum electrolytic capacitor across CIN may be needed to damp the input for a typical bench test setup.