JAJSHQ8D July   2019  – July 2021 TPS25832-Q1 , TPS25833-Q1

PRODUCTION DATA  

  1. 1 特長
  2. 2 アプリケーション
  3. 3 概要
  4. 4 Revision History
  5. 5 概要 (続き)
  6. 6 Device Comparison Table
  7. 7 Pin Configuration and Functions
  8. 8 Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Timing Requirements
    7. 8.7 Switching Characteristics
    8. 8.8 Typical Characteristics
  9. 9 Parameter Measurement Information
    1.     18
  10. 10Detailed Description
    1. 10.1 Overview
    2. 10.2 Functional Block Diagram
    3. 10.3 Feature Description
      1. 10.3.1  Buck Regulator
      2. 10.3.2  Enable/UVLO and Start-up
      3. 10.3.3  RT/SYNC
      4. 10.3.4  Spread-Spectrum Operation
      5. 10.3.5  VCC, VCC_UVLO
      6. 10.3.6  Minimum ON-time, Minimum OFF-time
      7. 10.3.7  Internal Compensation
      8. 10.3.8  Bootstrap Voltage (BOOT)
      9. 10.3.9  RSNS, RSET, RILIMIT, and RIMON
      10. 10.3.10 Overcurrent and Short Circuit Protection
        1. 10.3.10.1 Current Limit Setting using RILIMIT
        2. 10.3.10.2 Buck Average Current Limit Design Example
        3. 10.3.10.3 External MOSFET Gate Drivers
        4. 10.3.10.4 Cycle-by-Cycle Buck Current Limit
      11. 10.3.11 IEC and Overvoltage Protection
        1. 10.3.11.1 VBUS and VCSN/OUT Overvoltage Protection
        2. 10.3.11.2 DP_IN and DM_IN Protection
        3. 10.3.11.3 CC IEC and Overvoltage Protection
      12. 10.3.12 Cable Compensation
        1. 10.3.12.1 Cable Compensation Design Example
      13. 10.3.13 USB Port Control
      14. 10.3.14 FAULT Response
      15. 10.3.15 USB Specification Overview
      16. 10.3.16 USB Type-C® Basics
        1. 10.3.16.1 Configuration Channel
        2. 10.3.16.2 Detecting a Connection
        3. 10.3.16.3 Configuration Channel Pins CC1 and CC2
        4. 10.3.16.4 Current Capability Advertisement and VCONN Overload Protection
        5. 10.3.16.5 Plug Polarity Detection
      17. 10.3.17 Device Power Pins (IN, CSN/OUT, and PGND)
      18. 10.3.18 Thermal Shutdown
      19. 10.3.19 Power Wake
      20. 10.3.20 Thermal Sensing with NTC (TPS25833-Q1)
    4. 10.4 Device Functional Modes
      1. 10.4.1 Shutdown Mode
      2. 10.4.2 Standby Mode
      3. 10.4.3 Active Mode
      4. 10.4.4 Device Truth Table (TT)
      5. 10.4.5 USB Port Operating Modes
        1. 10.4.5.1 USB Type-C® Mode
        2. 10.4.5.2 Standard Downstream Port (SDP) Mode — USB 2.0, USB 3.0, and USB 3.1
        3. 10.4.5.3 Charging Downstream Port (CDP) Mode
        4. 10.4.5.4 Dedicated Charging Port (DCP) Mode (TPS25833-Q1 Only)
          1. 10.4.5.4.1 DCP BC1.2 and YD/T 1591-2009
          2. 10.4.5.4.2 DCP Divider-Charging Scheme
          3. 10.4.5.4.3 DCP 1.2-V Charging Scheme
        5. 10.4.5.5 DCP Auto Mode (TPS25833-Q1 Only)
      6. 10.4.6 High-Bandwidth Data-Line Switches (TPS25832-Q1 Only)
  11. 11Application and Implementation
    1. 11.1 Application Information
    2. 11.2 Typical Application
      1. 11.2.1 Design Requirements
      2. 11.2.2 Detailed Design Procedure
        1. 11.2.2.1  Output Voltage
        2. 11.2.2.2  Switching Frequency
        3. 11.2.2.3  Inductor Selection
        4. 11.2.2.4  Output Capacitor Selection
        5. 11.2.2.5  Input Capacitor Selection
        6. 11.2.2.6  Bootstrap Capacitor Selection
        7. 11.2.2.7  VCC Capacitor Selection
        8. 11.2.2.8  Enable and Under Voltage Lockout Set-Point
        9. 11.2.2.9  Current Limit Set-Point
        10. 11.2.2.10 Cable Compensation Set-Point
        11. 11.2.2.11 LD_DET, POL, and FAULT Resistor Selection
      3. 11.2.3 Application Curves
  12. 12Power Supply Recommendations
  13. 13Layout
    1. 13.1 Layout Guidelines
    2. 13.2 Ground Plane and Thermal Considerations
    3. 13.3 Layout Example
  14. 14Device and Documentation Support
    1. 14.1 Receiving Notification of Documentation Updates
    2. 14.2 サポート・リソース
    3. 14.3 Trademarks
    4. 14.4 Electrostatic Discharge Caution
    5. 14.5 Glossary
  15. 15Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

11.2.3 Application Curves

Unless otherwise specified the following conditions apply: VIN = 13.5 V, fSW = 400 kHz, L = 10 µH, COUT_CSP = 66 µF, COUT_CSN = 0.1 µF, CBUS = 1 µF, TA = 25 °C.
Unless otherwise specified the following conditions apply: VIN = 13.5 V, fSW = 400 kHz, L = 10 µH, COUT_CSP = 66 µF, COUT_CSN = 0.1 µF, CBUS = 1 µF, TA = 25 °C.GUID-593B7D8A-CBA0-482C-8320-A14770042665-low.gif
VOUT = 5.1 V fSW = 400 kHz
Figure 11-2 Buck Only Efficiency. Unless otherwise specified the following conditions apply: VIN = 13.5 V, fSW = 400 kHz, L = 10 µH, COUT_CSP = 66 µF, COUT_CSN = 0.1 µF, CBUS = 1 µF, TA = 25 °C.
GUID-9A0409BE-F264-4DB4-ACE0-B24A78FB4409-low.gif
VOUT = 5.1 V fSW = 400 kHz RSENS = 15 mΩ
Figure 11-4 Efficiency with Sense Resistor
GUID-ED2E14E7-B3A3-43FA-A075-F76D9C0FA521-low.gif
VOUT = 5.1 V fSW = 400 kHz
Figure 11-6 Load Regulation
GUID-15541E35-C060-4547-B92F-CEB586AB32AE-low.gif
ILOAD = 0 A to 3.5A RIMON = 0 Ω
Figure 11-8 Load Transient Without Cable Compensation
GUID-A22FCCF5-D0C8-407C-B7AB-320351A8E743-low.gif
ILOAD = 0 A to 3.5A RIMON = 13 kΩ
Figure 11-10 Load Transient With Cable Compensation
GUID-7B9BDEFC-97FB-4BAC-904A-7EA32EC6D2FB-low.gifFigure 11-12 Dropout Characteristic
GUID-D05C9981-F66C-4A1A-A9B1-678EDDBBAA4F-low.gif
RIMON = 13 kΩ
Figure 11-14 100-mA Output Ripple
GUID-39C2969D-A910-4E39-985F-A1558C4F5089-low.gif
VIN = 0 V to 13.5 V CC1 = Rd ILOAD = 3A
Figure 11-16 Startup Relate to VIN
GUID-35F47DC0-9B38-45BD-987F-E1A0F7EB8EB4-low.gif
EN = 0V to 5V CC1 = Rd ILOAD = 3A
Figure 11-18 Startup Relate to EN
GUID-3023DFE7-F7D5-4E54-93AB-4A65DD6A773E-low.gif
CC1 = Open to Rd CC2 = Open ILOAD = 3A
Figure 11-20 Rd Assert
GUID-5BCCA994-BE3B-4A25-984E-BBC5B09DF060-low.gif
EN to High VBUS = GND RLIMIT = 13 kΩ
Figure 11-22 Enable into Short Without External FET
GUID-29A45ECF-6E41-4CFF-AF5A-84F5B7216CA8-low.gif
EN to High VBUS = GND RLIMIT = 13 kΩ
Figure 11-24 Enable into 1-Ω Load Without External FET
GUID-CBFA30FB-6161-4E6D-83C6-84CA88349A49-low.gif
EN to High VBUS = GND RLIMIT = 6.8 kΩ
Figure 11-26 Enable into Short With External FET
GUID-6E0F22EC-BC15-44A6-9C4B-B38DDFAC8E77-low.gif
RLIMIT = 13 kΩ
Figure 11-28 VBUS Hot Short to GND Without External FET
GUID-256665A5-10B9-4F9F-B1CC-286622C194AB-low.gif
CC1 = Rd CC2 = Ra
Figure 11-30 CC2 Hot Short to GND
GUID-E0237725-970B-4738-BB7A-F1DB8CC031D8-low.gif
VNTC = 0 V to 4 V CC1 = Rd CC2 = OPEN
Figure 11-32 Thermal Sensing with NTC Behavior 2
GUID-BF167601-AF99-4520-93CE-A786902B7BFC-low.gif
VOUT = 5.1 V fSW = 2100 kHz
Figure 11-3 Buck Only Efficiency
GUID-B4813AC1-92BD-4B69-8E59-3D628CB4992A-low.gif
VOUT = 5.1 V fSW = 2100 kHz RSENS = 15 mΩ
Figure 11-5 Efficiency with Sense Resistor
GUID-0B21B79D-848E-42A3-AFB8-E5E2374E406E-low.gif
VOUT = 5.1 V fSW = 400 kHz
Figure 11-7 Line Regulation
GUID-1569200C-5631-4D1E-B50E-CB3CA888250D-low.gif
ILOAD = 0.75 A to 2.25A RIMON = 0 Ω
Figure 11-9 Load Transient Without Cable Compensation
GUID-3BEA1F48-00AD-4C37-BCA9-42D5E8DE582C-low.gif
ILOAD = 0.75 A to 2.25A RIMON = 13 kΩ
Figure 11-11 Load Transient With Cable Compensation
GUID-49E15BD3-B6BF-4F71-AD7D-0D3312725312-low.gif
RIMON = 13 kΩ
Figure 11-13 3.5-A Output Ripple
GUID-53F35D1A-7DBE-4B91-8B94-C747C5431DFD-low.gif
RIMON = 13 kΩ
Figure 11-15 No Load Output Ripple
GUID-93633391-0583-4D15-971E-02ABAF85427B-low.gif
VIN = 13.5 V to 0 V CC1 = Rd ILOAD = 3A
Figure 11-17 Shutdown Relate to VIN
GUID-F72E5193-853E-4015-BC27-99C46DD100A6-low.gif
EN = 5V to 0V CC1 = Rd ILOAD = 3A
Figure 11-19 Shutdown Relate to EN
GUID-C59DD347-8BBC-477E-80A1-E3EC3F549253-low.gif
CC1 = Rd to Open CC2 = Open ILOAD = 3A
Figure 11-21 Rd Desert
GUID-AEC8DE31-EF3B-4B25-A609-7CE2AD7F288D-low.gif
RLIMIT = 13 kΩ
Figure 11-23 Short Circuit Recovery Without External FET
GUID-7FAA47E5-A0B6-4C1F-A1A6-A7AA574F460C-low.gif
RLIMIT = 13 kΩ
Figure 11-25 1-Ω Load Recovery Without External FET
GUID-B57FF286-E962-4765-BAD2-0F9E644D53A8-low.gif
RLIMIT = 6.8 kΩ
Figure 11-27 Short Circuit Recovery With External FET
GUID-A0662C52-1949-40DB-9A86-EAFB5FD7E791-low.gif
RLIMIT = 6.8 kΩ
Figure 11-29 VBUS Hot Short to GND With External FET
GUID-27AFFEAB-2B40-4E43-89E7-75D5CB294850-low.gif
VNTC = 0V to 3V CC1 = Rd CC2 = OPEN
Figure 11-31 Thermal Sensing with NTC Behavior 1