SLVSAE1B October   2010  – September 2015 TPS65708

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Parameter Measurement Information
    1. 7.1 Setup
  8. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1  DC-DC Converters
      2. 8.3.2  Power Save Mode
      3. 8.3.3  Dynamic Voltage Positioning
      4. 8.3.4  Soft Start
      5. 8.3.5  100% Duty Cycle Low Dropout Operation
      6. 8.3.6  180° Out-of-Phase Operation
      7. 8.3.7  Undervoltage Lockout and Enable for DCDC1, DCDC2, LDO1, and LDO2
      8. 8.3.8  Output Voltage Discharge
      9. 8.3.9  Power-Up Sequencing
      10. 8.3.10 Short-Circuit Protection
      11. 8.3.11 Thermal Shutdown
      12. 8.3.12 LDOs
      13. 8.3.13 LED Driver
    4. 8.4 Device Functional Modes
  9. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Applications
      1. 9.2.1 Powering All Rails from the Input Supply of 5 V
        1. 9.2.1.1 Design Requirements
        2. 9.2.1.2 Detailed Design Procedure
          1. 9.2.1.2.1 Output Filter Design (Inductor and Output Capacitor)
            1. 9.2.1.2.1.1 Inductor Selection
            2. 9.2.1.2.1.2 Output Capacitor Selection
            3. 9.2.1.2.1.3 Input Capacitor Selection
        3. 9.2.1.3 Application Curve
      2. 9.2.2 Powering the LDOs From the Output of the DC-DC Converters to Improve Efficiency
  10. 10Power Supply Recommendations
  11. 11Layout
    1. 11.1 Layout Guidelines
    2. 11.2 Layout Example
  12. 12Device and Documentation Support
    1. 12.1 Device Support
      1. 12.1.1 Third-Party Products Disclaimer
    2. 12.2 Community Resources
    3. 12.3 Trademarks
    4. 12.4 Electrostatic Discharge Caution
    5. 12.5 Glossary
  13. 13Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

11 Layout

11.1 Layout Guidelines

  • All input capacitors should be soldered as close as possible to the device.
  • All inductors should be placed as close as possible to switching pins through thick trace.
  • All feedback traces should be routed differentially and away from noisy traces such as switching signals.

11.2 Layout Example

TPS65708 SLVSAE1_Layout.gif Figure 15. Layout Recommendation