JAJSHT2C august   2019  – december 2020 UCC28740-Q1

PRODUCTION DATA  

  1.   1
  2. 特長
  3. アプリケーション
  4. 概要
  5. Revision History
  6. Revision History
  7. Revision History
  8. Pin Configuration and Functions
    1. 7.1 Pin Functions
  9. Specifications
    1. 8.1 Absolute Maximum Ratings
    2. 8.2 ESD Ratings
    3. 8.3 Recommended Operating Conditions
    4. 8.4 Thermal Information
    5. 8.5 Electrical Characteristics
    6. 8.6 Switching Characteristics
    7. 8.7 Typical Characteristics
  10. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Detailed Pin Description
      2. 9.3.2 Valley-Switching and Valley-Skipping
      3. 9.3.3 Startup Operation
      4. 9.3.4 Fault Protection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Secondary-Side Optically Coupled Constant-Voltage (CV) Regulation
      2. 9.4.2 Primary-Side Constant-Current (CC) Regulation
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 High Voltage Applications
    3. 10.3 Typical Application
      1. 10.3.1 Design Requirements
      2. 10.3.2 Detailed Design Procedure
        1. 10.3.2.1  Custom Design With WEBENCH® Tools
        2. 10.3.2.2  Standby Power Estimate and No-Load Switching Frequency
        3. 10.3.2.3  Input Bulk Capacitance and Minimum Bulk Voltage
        4. 10.3.2.4  38
        5. 10.3.2.5  Transformer Turns-Ratio, Inductance, Primary Peak Current
        6. 10.3.2.6  Transformer Parameter Verification
        7. 10.3.2.7  VS Resistor Divider, Line Compensation
        8. 10.3.2.8  Output Capacitance
        9. 10.3.2.9  VDD Capacitance, CVDD
        10. 10.3.2.10 Feedback Network Biasing
      3. 10.3.3 Application Curves
  12. 11Power Supply Recommendations
  13. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 VDD Pin
      2. 12.1.2 VS Pin
      3. 12.1.3 FB Pin
      4. 12.1.4 GND Pin
      5. 12.1.5 CS Pin
      6. 12.1.6 DRV Pin
      7. 12.1.7 HV Pin
    2. 12.2 Layout Example
  14. 13Device and Documentation Support
    1. 13.1 Device Support
      1. 13.1.1 Development Support
        1. 13.1.1.1 Custom Design With WEBENCH® Tools
      2. 13.1.2 Device Nomenclature
        1. 13.1.2.1  Capacitance Terms in Farads
        2. 13.1.2.2  Duty Cycle Terms
        3. 13.1.2.3  Frequency Terms in Hertz
        4. 13.1.2.4  Current Terms in Amperes
        5. 13.1.2.5  Current and Voltage Scaling Terms
        6. 13.1.2.6  Transformer Terms
        7. 13.1.2.7  Power Terms in Watts
        8. 13.1.2.8  Resistance Terms in Ohms
        9. 13.1.2.9  Timing Terms in Seconds
        10. 13.1.2.10 Voltage Terms in Volts
        11. 13.1.2.11 AC Voltage Terms in VRMS
        12. 13.1.2.12 Efficiency Terms
    2. 13.2 Documentation Support
      1. 13.2.1 Related Documentation
    3. 13.3 Receiving Notification of Documentation Updates
    4. 13.4 Community Resources
    5. 13.5 Trademarks
  15.   Mechanical, Packaging, and Orderable Information

パッケージ・オプション

メカニカル・データ(パッケージ|ピン)
サーマルパッド・メカニカル・データ
発注情報

Voltage Terms in Volts

    VBLKThe highest bulk-capacitor voltage for standby power measurement.
    VBULK(min)The minimum valley voltage on CB1 and CB2 at full power.
    VCCRThe constant-current regulation factor (see Section 6.5).
    VCST(max)The CS-pin maximum current-sense threshold (see Section 6.5).
    VCST(min)The CS-pin minimum current-sense threshold (see Section 6.5).
    VDSPKThe MOSFET drain-to-source peak voltage at high line.
    VFThe secondary-rectifier forward-voltage drop at near-zero current.
    VFAThe auxiliary-rectifier forward-voltage drop.
    VLKThe estimated leakage-inductance energy reset voltage.
    VThe output voltage drop allowed during the load-step transient in CV mode.
    VOCBCThe target cable-compensation voltage added to VOCV (provided by an external adjustment circuit applied to the shunt-regulator). Set equal to 0 V if not used.
    VOCCThe converter lowest output voltage target while in constant-current regulation.
    VOCVThe regulated output voltage of the converter.
    VOVThe maximum allowable peak output voltage.
    VOVPThe overvoltage-detection level at the VS input (see Section 6.5).
    VREVAThe peak reverse voltage on the auxiliary rectifier.
    VREVSThe peak reverse voltage on the secondary rectifier.
    VRIPPLEThe output peak-to-peak ripple voltage at full-load.