74ACT16651
- Members of the Texas Instruments WidebusTM Family
- Inputs Are TTL-Voltage Compatible
- Inverting Data Paths
- Independent Registers and Enables for A and B Buses
- Multiplexed Real-Time and Stored Data
- Flow-Through Architecture Optimizes PCB Layout
- Distributed VCC and GND Pin Configurations Minimize High-Speed Switching Noise
- EPICTM (Enhanced-Performance Implanted CMOS) 1-
m Process - 500-mA Typical Latch-Up Immunity at 125°C
- Packaged in Plastic 300-mil Shrink Small-Outline (DL) Packages and 380-mil Fine-Pitch Ceramic Flat (WD) Packages Using 25-mil Center-to-Center Pin Spacings
EPIC and Widebus are trademarks of Texas Instruments Incorporated.
The SN54ACT16651 and 74ACT16651 are 16-bit bus transceivers that consist of D-type flip-flops and control circuitry arranged for multiplexed transmission of data directly from the data bus or from the internal storage registers. These devices can be used as two 8-bit transceivers or one 16-bit transceiver.
Complementary output-enable (OEAB and 
) inputs are provided to control
the transceiver functions. Select-control (SAB and SBA) inputs are
provided to select whether real-time or stored data is transferred. A
low input level selects real-time data, and a high input level
selects stored data. The circuitry used for select control eliminates
the typical decoding glitch that occurs in a multiplexer during the
transition between stored and real-time data. Figure 1 illustrates
the four fundamental bus-management functions that can be performed
with the SN54ACT16651 and 74ACT16651.
Data on the A or B bus, or both, can be stored in the internal D
flip-flops by low-to-high transitions at the appropriate clock (CLKAB
or CLKBA) inputs regardless of the levels on the select-control or
output-enable inputs. When SAB and SBA are in the real-time transfer
mode, it is also possible to store data without using the internal
D-type flip-flops by simultaneously enabling OEAB and . In this configuration, each
output reinforces its input. Thus, when all other data sources to the
two sets of bus lines are at high impedance, each set of bus lines
remains at its last state.
The 74ACT16651 is packaged in TI's shrink small-outline package, which provides twice the I/O pin count and functionality of standard small-outline packages in the same printed-circuit-board area.
The SN54ACT16651 is characterized for operation over the full military temperature range of -55°C to 125°C. The 74ACT16651 is characterized for operation from -40°C to 85°C.
관심 가지실만한 유사 제품
다른 핀 출력을 지원하지만 비교 대상 장치와 동일한 기능
비교 대상 장치와 유사한 기능
기술 문서
| 유형 | 직함 | 날짜 | ||
|---|---|---|---|---|
| * | Data sheet | 16-Bit Transceivers And Registers With 3-State Outputs datasheet (Rev. A) | 1996/04/01 | |
| Application note | Implications of Slow or Floating CMOS Inputs (Rev. E) | 2021/07/26 | ||
| Selection guide | Logic Guide (Rev. AB) | 2017/06/12 | ||
| Application note | Understanding and Interpreting Standard-Logic Data Sheets (Rev. C) | 2015/12/02 | ||
| User guide | LOGIC Pocket Data Book (Rev. B) | 2007/01/16 | ||
| Application note | Semiconductor Packing Material Electrostatic Discharge (ESD) Protection | 2004/07/08 | ||
| Application note | Selecting the Right Level Translation Solution (Rev. A) | 2004/06/22 | ||
| Application note | TI IBIS File Creation, Validation, and Distribution Processes | 2002/08/29 | ||
| Application note | CMOS Power Consumption and CPD Calculation (Rev. B) | 1997/06/01 | ||
| Application note | Designing With Logic (Rev. C) | 1997/06/01 | ||
| Application note | Using High Speed CMOS and Advanced CMOS in Systems With Multiple Vcc | 1996/04/01 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치