CDCF2509은(는) 새 설계에 권장하지 않습니다.
이 제품은 기존 고객을 위해 계속 제공됩니다. 새로운 설계는 대체 제품을 고려해야 합니다.
open-in-new 대안 비교
비교 대상 장치와 동일한 기능을 지원하는 핀 대 핀
CDCVF2509 활성 DRAM 애플리케이션용 9개 출력을 지원하는 3.3V 위상 잠금 루프 클록 드라이버 Can achieve better performance

제품 상세 정보

Function Single-ended Operating temperature range (°C) 0 to 70 Rating Catalog
Function Single-ended Operating temperature range (°C) 0 to 70 Rating Catalog
TSSOP (PW) 24 49.92 mm² 7.8 x 6.4
  • Use CDCVF2509A as a Replacement for this Device
  • Designed to Meet PC133 SDRAM Registered DIMM Specification Rev. 0.9
  • Spread Spectrum Clock Compatible
  • Operating Frequency 25 MHz to 140 MHz
  • Static Phase Error Distribution at 66 MHz to 133 MHz is ±125 ps
  • Jitter (cyc-cyc) at 66 MHz to 133 MHz Is |70| ps
  • Available in Plastic 24-Pin TSSOP
  • Phase-Lock Loop Clock Distribution for Synchronous DRAM Applications
  • Distributes One Clock Input to One Bank of Five and One Bank of Four Outputs
  • Separate Output Enable for Each Output Bank
  • External Feedback (FBIN) Terminal Is Used to Synchronize the Outputs to the Clock Input
  • On-Chip Series Damping Resistors
  • No External RC Network Required
  • Operates at 3.3 V
  • Use CDCVF2509A as a Replacement for this Device
  • Designed to Meet PC133 SDRAM Registered DIMM Specification Rev. 0.9
  • Spread Spectrum Clock Compatible
  • Operating Frequency 25 MHz to 140 MHz
  • Static Phase Error Distribution at 66 MHz to 133 MHz is ±125 ps
  • Jitter (cyc-cyc) at 66 MHz to 133 MHz Is |70| ps
  • Available in Plastic 24-Pin TSSOP
  • Phase-Lock Loop Clock Distribution for Synchronous DRAM Applications
  • Distributes One Clock Input to One Bank of Five and One Bank of Four Outputs
  • Separate Output Enable for Each Output Bank
  • External Feedback (FBIN) Terminal Is Used to Synchronize the Outputs to the Clock Input
  • On-Chip Series Damping Resistors
  • No External RC Network Required
  • Operates at 3.3 V

The CDCF2509 is a high-performance, low-skew, low-jitter, phase-lock loop (PLL) clock driver. It uses a PLL to precisely align, in both frequency and phase, the feedback (FBOUT) output to the clock (CLK) input signal. It is specifically designed for use with synchronous DRAMs. The CDCF2509 operates at 3.3 V VCC. It also provides integrated series-damping resistors that make it ideal for driving point-to-point loads.

One bank of five outputs and one bank of four outputs provide nine low-skew, low-jitter copies of CLK. Output signal duty cycles are adjusted to 50%, independent of the duty cycle at CLK. Each bank of outputs is enabled or disabled separately via the control (1G and 2G) inputs. When the G inputs are high, the outputs switch in phase and frequency with CLK; when the G inputs are low, the outputs are disabled to the logic-low state.

Unlike many products containing PLLs, the CDCF2509 does not require external RC networks. The loop filter for the PLL is included on-chip, minimizing component count, board space, and cost.

Because it is based on PLL circuitry, the CDCF2509 requires a stabilization time to achieve phase lock of the feedback signal to the reference signal. This stabilization time is required following power up and application of a fixed-frequency, fixed-phase signal at CLK, and following any changes to the PLL reference or feedback signals. The PLL can be bypassed for test purposes by strapping AVCC to ground.

The CDCF2509 is characterized for operation from 0°C to 85°C.

For application information refer to application reports High Speed Distribution Design Techniques for CDC509/516/2509/2510/2516 (literature number SLMA003) and Using CDC2509A/2510A PLL with Spread Spectrum Clocking (SSC) (literature number SCAA039).

The CDCF2509 is a high-performance, low-skew, low-jitter, phase-lock loop (PLL) clock driver. It uses a PLL to precisely align, in both frequency and phase, the feedback (FBOUT) output to the clock (CLK) input signal. It is specifically designed for use with synchronous DRAMs. The CDCF2509 operates at 3.3 V VCC. It also provides integrated series-damping resistors that make it ideal for driving point-to-point loads.

One bank of five outputs and one bank of four outputs provide nine low-skew, low-jitter copies of CLK. Output signal duty cycles are adjusted to 50%, independent of the duty cycle at CLK. Each bank of outputs is enabled or disabled separately via the control (1G and 2G) inputs. When the G inputs are high, the outputs switch in phase and frequency with CLK; when the G inputs are low, the outputs are disabled to the logic-low state.

Unlike many products containing PLLs, the CDCF2509 does not require external RC networks. The loop filter for the PLL is included on-chip, minimizing component count, board space, and cost.

Because it is based on PLL circuitry, the CDCF2509 requires a stabilization time to achieve phase lock of the feedback signal to the reference signal. This stabilization time is required following power up and application of a fixed-frequency, fixed-phase signal at CLK, and following any changes to the PLL reference or feedback signals. The PLL can be bypassed for test purposes by strapping AVCC to ground.

The CDCF2509 is characterized for operation from 0°C to 85°C.

For application information refer to application reports High Speed Distribution Design Techniques for CDC509/516/2509/2510/2516 (literature number SLMA003) and Using CDC2509A/2510A PLL with Spread Spectrum Clocking (SSC) (literature number SCAA039).

다운로드

기술 자료

star =TI에서 선정한 이 제품의 인기 문서
검색된 결과가 없습니다. 검색어를 지우고 다시 시도하십시오.
1개 모두 보기
유형 직함 날짜
* Data sheet CDCF2509: 3.3-V Phase-Lock Loop Clock Driver datasheet (Rev. C) 2004/12/02

주문 및 품질

포함된 정보:
  • RoHS
  • REACH
  • 디바이스 마킹
  • 납 마감/볼 재질
  • MSL 등급/피크 리플로우
  • MTBF/FIT 예측
  • 물질 성분
  • 인증 요약
  • 지속적인 신뢰성 모니터링
포함된 정보:
  • 팹 위치
  • 조립 위치