TAS2780
- 24-V Supply for Class-D Output Stage
- Y-Bridge Multi-Level Supply Architecture
- Spread Spectrum Control
- Ultrasonic Output Support up to 40 kHz
- 25 W, 1% THD+N (4 Ω, 18 V)
- 30 W Maximum Output Power, 10 % THD+N
- 83% at 1W, 4 Ω, PVDD = 12 V, VBAT1S = 3.8 V
- 83% at 1W, 8 Ω, PVDD = 18 V, VBAT1S = 5 V
- 85% at 1W, 4 Ω, PVDD = 18 V, VBAT1S = 5 V
- 89% at 15W, 4 Ω, PVDD = 18 V, VBAT1S = 5 V
- 93% at 15W , 8 Ω, PVDD = 18 V, VBAT1S = 5 V
- <0.5 µA in Hardware Shutdown Mode
- PVDD: 3 V to 24 V
- VBAT1S: 2.7 V to 5.5 V
- AVDD: 1.8 V
- IOVDD: 1.8 V/ 3.3 V
- SDOUT for Echo Cancellation
- I2S/TDM: 8 Channels of 32 bits up to 96 KSPS
- I2C: Selectable Addresses with Fast Mode+
- Inter-Chip Communication Bus
- 44.1 kHz to 96 kHz Sample Rates
- Real-time IV-Sense for Speaker Protection
- Short and Open Load Protection
- Thermal and Over Current Protection
- Brownout Protection with Power Limiter
- Over Power and Low Battery Protection
- PVDD and VBAT1S Supply Tracking Limiters
- Thermal Foldback
- Post Filter Feedback
- Output Slew Rate Control
The TAS2780 is a mono, digital input Class-D audio amplifier optimized for efficiently driving high peak power into loudspeakers. The Class-D amplifier is capable of delivering 25 W of continuous power into a 4 Ω load with less than 1% THD+N at a supply voltage of 18 V. The broad voltage input range and the high output power makes this amplifier versatile enough to work with battery or line powered systems.
The TAS2780 can be used as a conventional amp or with host-based speaker protection algorithms. The integrated speaker voltage and current sense provides for real time feedback of loudspeaker conditions to the protection algorithms through a return I2S path.
Y-Bridge power architecture improves amplifier efficiency by internally selecting the supplies for optimal headroom. Brownout prevention scheme with multiple thresholds allows reducing the gain in signal path when the supply drops.
Up to eight TAS2780 devices can share a common bus via I2S/TDM and I2C/SPI interfaces.
The TAS2780 is available in a 30 pin HR-QFN package for a compact PCB footprint.
추가 정보 요청
TAS2780 PurePath™ 콘솔 소프트웨어 및 기타 설계 리소스를 요청하세요: 지금 요청하기
기술 문서
유형 | 직함 | 날짜 | ||
---|---|---|---|---|
* | Data sheet | TAS2780 Digital Input Mono Class-D Audio Amplifier With Speaker IV Sense datasheet (Rev. B) | PDF | HTML | 2023/01/05 |
Application note | TAS27xx Introduction to Click and Pop Noise Measurement in Class-D Audio Amplifiers | PDF | HTML | 2024/03/26 | |
Application note | Y-Bridge in Class-D Amplifiers for Improving Efficiency | PDF | HTML | 2021/11/19 | |
User guide | TAS2780EVM User's Guide (Rev. A) | 2021/10/28 | ||
Certificate | TAS2780EVM EU RoHS Declaration of Conformity (DoC) | 2021/05/21 | ||
Technical article | How smart amps are bringing high-fidelity audio into the smart home | PDF | HTML | 2021/05/03 | |
Application note | Limitations of Capacitor only EMI Filters on Class-D Amplifiers | PDF | HTML | 2020/07/21 | |
Application note | Requesting Access to Audio Software | 2020/06/18 | ||
Application note | PCB Layout Guidelines for TAS2xxx Series Class-D Non-boosted Audio Amplifier | 2019/06/27 |
설계 및 개발
추가 조건 또는 필수 리소스는 사용 가능한 경우 아래 제목을 클릭하여 세부 정보 페이지를 확인하세요.
TAS2780EVM — TAS2780 스피커 IV 센서가 탑재된 디지털 입력 모노 클래스 D 오디오 증폭기용 평가 모듈
TAS2780EVM 평가 모듈(EVM)은 스피커 IV 센서가 탑재된 디지털 입력 모노 클래스 D 오디오 증폭기 TAS2780 평가에 사용됩니다. 이 EVM은 독립형 평가 도구로 사용하도록 설계되었으며, 설계자에게 TAS2780 증폭기를 시스템에 통합할 수 있는 도구와 모노 스피커 출력을 제공합니다. 설계자는 PurePath™ Console 3 소프트웨어를 사용하여 디바이스를 제어 및 구성할 수 있으며, 스피커의 특성을 분석하고 알고리즘을 적절하게 튜닝할 수 있습니다. 이러한 기능은 (...)
PUREPATHCONSOLE — 오디오 시스템 설계 및 개발을 위한 PurePath™ 콘솔 그래픽 개발 제품군
PurePath Console’s (...)
PSPICE-FOR-TI — TI 설계 및 시뮬레이션 툴용 PSpice®
TI 설계 및 시뮬레이션 환경용 PSpice는 기본 제공 라이브러리를 이용해 복잡한 혼합 신호 설계를 시뮬레이션할 수 있습니다. 레이아웃 및 제작에 (...)
패키지 | 핀 | 다운로드 |
---|---|---|
VQFN-HR (RYA) | 30 | 옵션 보기 |
주문 및 품질
- RoHS
- REACH
- 디바이스 마킹
- 납 마감/볼 재질
- MSL 등급/피크 리플로우
- MTBF/FIT 예측
- 물질 성분
- 인증 요약
- 지속적인 신뢰성 모니터링
- 팹 위치
- 조립 위치
권장 제품에는 본 TI 제품과 관련된 매개 변수, 평가 모듈 또는 레퍼런스 디자인이 있을 수 있습니다.