LMV393
- 2.7-V and 5-V Performance
- Low Supply Current
- LMV331 130 µA Typ
- LMV393 210 µA Typ
- LMV339 410 µA Typ
- Input Common-Mode Voltage Range Includes Ground
- Low Output Saturation Voltage 200 mV Typical
- Open-Collector Output for Maximum Flexibility
The LMV393 and LMV339 devices are low-voltage (2.7 V to 5.5 V) versions of the dual and quad comparators, LM393 and LM339, which operate from 5 V to 30 V. The LMV331 is the single-comparator version.
The LMV331, LMV339, and LMV393 are the most cost-effective solutions for applications where low-voltage operation, low power, and space saving are the primary specifications in circuit design for portable consumer products. These devices offer specifications that meet or exceed the familiar LM339 and LM393 devices at a fraction of the supply current.
技術文件
找不到結果。請清除您的搜尋條件,然後再試一次。
檢視所有 2 類型 | 標題 | 日期 | ||
---|---|---|---|---|
* | Data sheet | LMV331 Single, LMV393 Dual, LMV339 Quad General-purpose Low-voltage Comparators datasheet (Rev. U) | PDF | HTML | 2020年 11月 10日 |
E-book | The Signal e-book: A compendium of blog posts on op amp design topics | 2017年 3月 28日 |
設計與開發
如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。
模擬工具
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
模擬工具
TINA-TI — 基於 SPICE 的類比模擬程式
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
參考設計
TIDA-010065 — 基於高效、低排放、隔離式 DC/DC 轉換器的類比輸入模組參考設計
此參考設計為一簡化架構,可產生隔離式電源供應,適用於測量隔離電壓與電流的隔離式放大器。具 5-V 輸入之強化隔離操作的完全整合式 DC/DC 轉換器,並具備可設定 5-V 或 5.4-V 輸出 (適用於低壓降穩壓器 (LDO) 的空餘空間) 可產生隔離電源。連接到 ±50-mV 輸入範圍隔離放大器,且配置爲通道隔離輸入的分流,可測量電流。連接到 ±250-mV 或 ±12-V 輸入範圍隔離放大器,且配置爲群組隔離輸入的潛在分頻器,可測量電壓。隔離放大器介面直接輸出至 24 位 Δ Σ 類比轉數位轉換器 (ADC),或使用增益放大器擴展至 (...)
封裝 | 引腳 | 下載 |
---|---|---|
SOIC (D) | 8 | 檢視選項 |
TSSOP (PW) | 8 | 檢視選項 |
VSSOP (DDU) | 8 | 檢視選項 |
VSSOP (DGK) | 8 | 檢視選項 |
訂購與品質
內含資訊:
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 資格摘要
- 進行中可靠性監測
內含資訊:
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。