TAS5751M
- Audio Input/Output
- One-Stereo Serial Audio Input
- Supports 44.1-kHz and 48-kHz Sample Rates (LJ/RJ/I²S)
- Supports 3-Wire I²S Mode (no MCLK required)
- Automatic Audio Port Rate Detection
- Supports BTL and PBTL Configuration
- POUT = 25 W at 10% THD+N
- PVDD = 20 V, 8 Ω, 1 kHz
- Audio/PWM Processing
- Independent Channel Volume Controls With Gain of 24 dB to Mute in 0.125-dB Steps
- Programmable Three-Band Automatic Gain Limiting (AGL)
- 20 Programmable Biquads for Speaker EQ and Other Audio-Processing Features
- General Features
- 106-dB SNR, A-Weighted, Referenced to Full Scale (0 dB)
- I²C Serial Control Interface w/ two Addresses
- Thermal, Short-Circuit, and Undervoltage Protection
- Up to 90% Efficient
- AD, BD, and Ternary Modulation
- PWM Level Meter
The TAS5751M device is an efficient, digital-input audio amplifier for driving stereo speakers configured as a bridge tied load (BTL). In parallel bridge tied load (PBTL) in can produce higher power by driving the parallel outputs into a single lower impedance load. One serial data input allows processing of up to two discrete audio channels and seamless integration to most digital audio processors and MPEG decoders. The device accepts a wide range of input data and data rates. A fully programmable data path routes these channels to the internal speaker drivers.
The TAS5751M device is a slave-only device receiving all clocks from external sources. The TAS5751M device operates with a PWM carrier between a 384-kHz switching rate and a 288-kHz switching rate, depending on the input sample rate. Oversampling combined with a fourth-order noise shaper provides a flat noise floor and excellent dynamic range from 20 Hz to 20 kHz.
要求更多資訊
提供 PurePath™ Console 3、TAS5751M GUI 和其他設計資源。立即索取
技術文件
類型 | 標題 | 日期 | ||
---|---|---|---|---|
* | Data sheet | TAS5751M - Digital Input Audio Power Amplifier with EQ and 3-Band AGL datasheet (Rev. B) | PDF | HTML | 2018年 5月 15日 |
More literature | TAS5751MEVM Quick Start Guide (Rev. A) | 2016年 7月 20日 |
設計與開發
如需其他條款或必要資源,請按一下下方的任何標題以檢視詳細頁面 (如有)。
PUREPATH-CMBEVM — 適用於音訊系統設計和開發的 PurePath™ Console 主機板
The PurePath™ Console Motherboard (PurePath-CMBEVM) provides a seamless interface between Ti’s latest PurePath Console GUI to supported TI’s digital and mixed-signal audio evaluation modules, including audio amplifiers and audio converters.
The PurePath-CMBEVM is shipped as a stand-alone board. It (...)
TAS5751MEVM — TAS5751M 數位輸入、開迴路 D 類音訊放大器評估模組
The TAS5751MEVM allows evaluation of the TAS5751M, I2S-input, open-loop amplifier from Texas Instruments. The evaluation module is populated with two TAS5751M devices, one configured for two channel operation and one configured for mono operation. The TAS5751M combines a PWM processor with an (...)
PUREPATHCONSOLE — 適用於音訊系統設計和開發的 PurePath™ Console 圖形開發套件
PurePath Console’s (...)
PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具
封裝 | 引腳 | 下載 |
---|---|---|
HTSSOP (DCA) | 48 | 檢視選項 |
訂購與品質
- RoHS
- REACH
- 產品標記
- 鉛塗層/球物料
- MSL 等級/回焊峰值
- MTBF/FIT 估算值
- 材料內容
- 資格摘要
- 進行中可靠性監測
- 晶圓廠位置
- 組裝地點
建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。