首頁 音訊 音訊放大器 喇叭放大器
首頁
音訊
音訊放大器
喇叭放大器

TPA6404-Q1

現行

具負載突降的車用 45-W、2-MHz、4 通道 4.5 至 18-V 電源類比輸入 D 類音訊放大器

立即訂購
產品規格表

TPA6404-Q1

現行
產品規格表 立即訂購

產品詳細資料

Audio input type Analog Input Architecture Class-D Speaker channels (max) 4 Rating Automotive Power stage supply (max) (V) 18 Power stage supply (min) (V) 4.5 Load (min) (Ω) 2 Output power (W) 45 THD + N at 1 kHz (%) 0.01 Iq (typ) (mA) 155 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 4.5 Analog supply voltage (max) (V) 18 PSRR (dB) 75 Operating temperature range (°C) -40 to 125
Audio input type Analog Input Architecture Class-D Speaker channels (max) 4 Rating Automotive Power stage supply (max) (V) 18 Power stage supply (min) (V) 4.5 Load (min) (Ω) 2 Output power (W) 45 THD + N at 1 kHz (%) 0.01 Iq (typ) (mA) 155 Control interface I2C Closed/open loop Closed Analog supply (min) (V) 4.5 Analog supply voltage (max) (V) 18 PSRR (dB) 75 Operating temperature range (°C) -40 to 125
HSSOP (DKQ) 56 190.647 mm² 18.42 x 10.35
  • Advanced Load Diagnostics
    • AC Diagnostic for Tweeter Detection with Impedance and Phase Response
    • Integrated sine wave Generator
  • Easy to meet CISPR25-L5 EMC specification
  • AEC-Q100 Qualified With the Following Results for Automotive Applications:
    • Device Temperature Grade 1: –40°C to 125°C Ambient Operating Temperature Range
    • Device HBM ESD Classification Level: 3A
    • Device CDM ESD Classification Level: C4B
  • Audio Inputs
    • 4 Channel Differential Analog Input
    • Four I2C-Controlled Gain Options
    • High Input Impedance for Low Value AC-coupling Capacitor
  • Audio Outputs
    • Four-Channel Bridge-Tied Load (BTL), with Option of Parallel BTL (PBTL)
    • Up to 2.1 MHz Output Switching Frequency
    • 27 W, 10% THD into 4 Ω at 14.4 V
    • 45 W, 10% THD into 2 Ω at 14.4 V
    • 85 W, 10% THD into 1 Ω at 14.4 V PBTL
  • Audio Performance into 4 Ω at 14.4 V, 1 kHz
    • THD+N < 0.01%
    • 42 µVRMS Output Noise
    • - 90 dB Crosstalk
  • Load Diagnostics
    • Output Open and Shorted Load
    • Output-to-Battery or Ground Shorts
    • Line Output Detection Up to 6 kΩ
    • Runs without Input Clocks
  • Protection
    • Output Current Limiting
    • Output Short Protection
    • 40 V Load Dump
    • Fortuitous Open Ground and Power Tolerant
    • DC Offset
    • Over Temperature
    • Undervoltage and Overvoltage
  • General Operation
    • 4.5 V to 18 V supply voltage
    • I2C Control With 4 Address Options
    • Clip Detection and Thermal Foldback
  • Advanced Load Diagnostics
    • AC Diagnostic for Tweeter Detection with Impedance and Phase Response
    • Integrated sine wave Generator
  • Easy to meet CISPR25-L5 EMC specification
  • AEC-Q100 Qualified With the Following Results for Automotive Applications:
    • Device Temperature Grade 1: –40°C to 125°C Ambient Operating Temperature Range
    • Device HBM ESD Classification Level: 3A
    • Device CDM ESD Classification Level: C4B
  • Audio Inputs
    • 4 Channel Differential Analog Input
    • Four I2C-Controlled Gain Options
    • High Input Impedance for Low Value AC-coupling Capacitor
  • Audio Outputs
    • Four-Channel Bridge-Tied Load (BTL), with Option of Parallel BTL (PBTL)
    • Up to 2.1 MHz Output Switching Frequency
    • 27 W, 10% THD into 4 Ω at 14.4 V
    • 45 W, 10% THD into 2 Ω at 14.4 V
    • 85 W, 10% THD into 1 Ω at 14.4 V PBTL
  • Audio Performance into 4 Ω at 14.4 V, 1 kHz
    • THD+N < 0.01%
    • 42 µVRMS Output Noise
    • - 90 dB Crosstalk
  • Load Diagnostics
    • Output Open and Shorted Load
    • Output-to-Battery or Ground Shorts
    • Line Output Detection Up to 6 kΩ
    • Runs without Input Clocks
  • Protection
    • Output Current Limiting
    • Output Short Protection
    • 40 V Load Dump
    • Fortuitous Open Ground and Power Tolerant
    • DC Offset
    • Over Temperature
    • Undervoltage and Overvoltage
  • General Operation
    • 4.5 V to 18 V supply voltage
    • I2C Control With 4 Address Options
    • Clip Detection and Thermal Foldback

The TPA6404-Q1 device is a four-channel analog-input Class-D audio amplifier that implements a 2.1 MHz PWM switching frequency that enables a cost optimized solution in a very small 4.5 cm2 PCB size, full operation down to 4.5 V for start/stop events, and exceptional sound quality with up to 100 kHz audio bandwidth.

The TPA6404-Q1 Class-D audio amplifier has an optimal design for use in entry level automotive head units that provide analog audio input signals as part of their system design.

The Class-D topology dramatically improves efficiency over traditional linear amplifier solutions.

The output switching frequency operates above the AM band, which eliminates the AM band interference and reduces the output filter size and cost.

The device is offered in a 56 pin HSSOP package with the exposed thermal pad up.

The TPA6404-Q1 device is a four-channel analog-input Class-D audio amplifier that implements a 2.1 MHz PWM switching frequency that enables a cost optimized solution in a very small 4.5 cm2 PCB size, full operation down to 4.5 V for start/stop events, and exceptional sound quality with up to 100 kHz audio bandwidth.

The TPA6404-Q1 Class-D audio amplifier has an optimal design for use in entry level automotive head units that provide analog audio input signals as part of their system design.

The Class-D topology dramatically improves efficiency over traditional linear amplifier solutions.

The output switching frequency operates above the AM band, which eliminates the AM band interference and reduces the output filter size and cost.

The device is offered in a 56 pin HSSOP package with the exposed thermal pad up.
open-in-new 尋找其它 喇叭放大器
下載 觀看有字幕稿的影片 影片
Information

要求更多資訊

提供完整的產品規格表和其他資訊。立即索取

提供 PurePath™ Console 3、TPA6404-Q1 GUI 和其他設計資源。立即索取

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 5
類型 標題 日期
* Data sheet TPA6404-Q1 45-W,​​​ 2-MHz Analog Input -Channel Automotive Class-D Audio Amplifier With Load Dump Protection and I2C Diagnostics datasheet (Rev. A) PDF | HTML 2018年 2月 14日
Application brief Diagnostics and Protections in Automotive Audio Systems (Rev. A) 2019年 9月 24日
Application note Inductor Selection Guide for 2.1 MHz Class-D Amplifiers (Rev. A) 2019年 9月 5日
EVM User's guide TPA6404Q1 EVM User's Guide (Rev. A) 2018年 2月 15日
Technical article Why you should use a Class-D audio amplifier in your automotive infotainment syste PDF | HTML 2018年 1月 8日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TPA6404Q1EVM — TPA6404-Q1 50W、2 MHz 類比輸入四通道車用 D 類音訊放大器評估模組

The TPA6404Q1EVM evaluation module (EVM) demonstrates the TPA6404-Q1 integrated circuit from Texas Instruments. The TPA6404-Q1 device is a four-channel analog-input Class-D audio amplifier that implements a 2.1 MHz PWM switching frequency that enables a cost optimized solution in a very small PCB (...)

使用指南: PDF
TI.com 無法提供
模擬型號

TPA6404-Q1 IBIS Model

SLOM440.ZIP (23 KB) - IBIS Model
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
封裝 引腳 下載
HSSOP (DKQ) 56 檢視選項
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 資格摘要
  • 進行中可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片