首頁 介面 USB IC USB 轉接驅動器與多工器
首頁
介面
USB IC
USB 轉接驅動器與多工器

TUSB217-Q1

現行

具有 DC 升壓、整合式 CDP 和寬電源的車用 USB 2.0 高速訊號調節器

立即訂購
產品規格表

TUSB217-Q1

現行
產品規格表 立即訂購

產品詳細資料

Type Redriver Function USB 2.0 USB speed (MBits) 480 Number of channels 1 Supply voltage (max) (V) 6.5 Supply voltage (min) (V) 2.3 Input/output voltage (min) (V) 0 Input/output voltage (max) (V) 3.6 Configuration USB 2.0 Single Port Features USB 2.0 Redriver with 5 Meter Cable Redriving Strength Auto Qaulified RGY Package Rating Automotive Operating temperature range (°C) -40 to 105 Supply current (max) (µA) 36000 ESD HBM (typ) (kV) 2 Bandwidth (MHz) 240
Type Redriver Function USB 2.0 USB speed (MBits) 480 Number of channels 1 Supply voltage (max) (V) 6.5 Supply voltage (min) (V) 2.3 Input/output voltage (min) (V) 0 Input/output voltage (max) (V) 3.6 Configuration USB 2.0 Single Port Features USB 2.0 Redriver with 5 Meter Cable Redriving Strength Auto Qaulified RGY Package Rating Automotive Operating temperature range (°C) -40 to 105 Supply current (max) (µA) 36000 ESD HBM (typ) (kV) 2 Bandwidth (MHz) 240
VQFN (RGY) 14 12.25 mm² 3.5 x 3.5
  • AEC-Q100 Qualified for Automotive Applications
    • Device Temperature Grade 2:
      –40°C to 105°C TA
  • Wide Supply Voltage Range: 2.3 - 6.5 V
  • Ultra-low USB Disconnect and Shutdown Power Consumption
  • Provides USB 2.0 High Speed Signal Conditioning
  • Compatible with USB 2.0, OTG 2.0 and BC 1.2
  • Support for Low Speed, Full Speed, High Speed Signaling
  • Host/Device Agnostic
  • Supports up to 5m Cable Length
    • Four Selectable Signal Boost (Edge Boost Along with DC Boost) Setting via External Pull Down Resistor
    • Three Selectable RX Sensitivity via Pull Up or Down Configurable Pin to Compensate ISI Jitter for High Loss Applications
  • Scalable Solution - Daisy Chain Devices for High Loss Applications
  • Pin Compatible with TUSB213 (5V)
  • AEC-Q100 Qualified for Automotive Applications
    • Device Temperature Grade 2:
      –40°C to 105°C TA
  • Wide Supply Voltage Range: 2.3 - 6.5 V
  • Ultra-low USB Disconnect and Shutdown Power Consumption
  • Provides USB 2.0 High Speed Signal Conditioning
  • Compatible with USB 2.0, OTG 2.0 and BC 1.2
  • Support for Low Speed, Full Speed, High Speed Signaling
  • Host/Device Agnostic
  • Supports up to 5m Cable Length
    • Four Selectable Signal Boost (Edge Boost Along with DC Boost) Setting via External Pull Down Resistor
    • Three Selectable RX Sensitivity via Pull Up or Down Configurable Pin to Compensate ISI Jitter for High Loss Applications
  • Scalable Solution - Daisy Chain Devices for High Loss Applications
  • Pin Compatible with TUSB213 (5V)

The TUSB217-Q1 is a third generation USB 2.0 high speed signal conditioner designed to compensate both AC loss (due to capacitive load) and DC loss (due to resistive loss) in the transmission channel.

The TUSB217-Q1 has a patented design that speeds up transition edges of USB 2.0 high speed signal with an edge booster and increases static levels with a DC boost function. In addition, the TUSB217-Q1 includes a pre-equalization function to improve the receiver sensitivity and compensate the ISI jitter in application with longer cable length. USB low speed and full speed signal characteristics are unaffected by the TUSB217-Q1.

The TUSB217-Q1 improves signal quality without altering packet timing or adding propagation delay, making it ideal for applications that require low latency.

The TUSB217-Q1 helps a system to pass the USB 2.0 high speed electrical near end eye compliance tests with a cable as long as 5 meters.

The TUSB217-Q1 is compatible with the USB On-The-Go (OTG) and Battery Charging (BC 1.2) protocols.

The TUSB217-Q1 is a third generation USB 2.0 high speed signal conditioner designed to compensate both AC loss (due to capacitive load) and DC loss (due to resistive loss) in the transmission channel.

The TUSB217-Q1 has a patented design that speeds up transition edges of USB 2.0 high speed signal with an edge booster and increases static levels with a DC boost function. In addition, the TUSB217-Q1 includes a pre-equalization function to improve the receiver sensitivity and compensate the ISI jitter in application with longer cable length. USB low speed and full speed signal characteristics are unaffected by the TUSB217-Q1.

The TUSB217-Q1 improves signal quality without altering packet timing or adding propagation delay, making it ideal for applications that require low latency.

The TUSB217-Q1 helps a system to pass the USB 2.0 high speed electrical near end eye compliance tests with a cable as long as 5 meters.

The TUSB217-Q1 is compatible with the USB On-The-Go (OTG) and Battery Charging (BC 1.2) protocols.

filter 尋找其它 USB 轉接驅動器與多工器
下載 觀看有字幕稿的影片 影片

技術文件

star =TI 所選的此產品重要文件
找不到結果。請清除您的搜尋條件，然後再試一次。
檢視所有 2
類型 標題 日期
* Data sheet TUSB217-Q1 USB High Speed Signal Conditioner datasheet (Rev. A) PDF | HTML 2018年 12月 13日
Application note TUSB217-Q1 Configuration Guidelines 2019年 4月 3日

設計與開發

如需其他條款或必要資源，請按一下下方的任何標題以檢視詳細頁面 (如有)。

開發板

TUSB217EVM — USB 2.0 高速訊號調節器評估模組

The TUSB217 evaluation module (EVM) can be used to evaluate the signal conditioning abilities of the TUSB217 device for various applications.
使用指南: PDF
TI.com 無法提供
模擬型號

TUSB217 S-Parameter Model

SLLM418.ZIP (322 KB) - S-Parameter Model
下載
模擬工具

PSPICE-FOR-TI — PSpice® for TI 設計與模擬工具

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
要求
模擬工具

TINA-TI — 基於 SPICE 的類比模擬程式

TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
使用指南: PDF
檢視選項
參考設計

TIDA-01432 — 具有充電和強化資料路徑性能的車用被動式媒體中心參考設計

This automotive reference design demonstrates a unique approach for media ports that require data transfers. This design has the capability to support USB 2.0 through a 15-W USB Type-C™ port. Customers can accelerate their media port systems by taking advantage of a complete reference design (...)
Design guide: PDF
電路圖: PDF
參考設計

PMP40544 — 符合 3-m USB-IF 近端規範的車用 USB Type-A 充電器參考設計

This reference design is for an automotive USB Type-A charger with 3 meters USB-IF near-end compliant. The TPS25840-Q1 is used as DC-DC regulator and data switch and TUSB217-Q1 is used as high speed signal conditioner to improve signal quality. The efficiency of the solution is 93.3% at a 12-W (...)
Test report: PDF
電路圖: PDF
封裝 引腳 下載
VQFN (RGY) 14 檢視選項
適用 TI 的評估品項標準條款與條件。

訂購與品質

內含資訊：
  • RoHS
  • REACH
  • 產品標記
  • 鉛塗層/球物料
  • MSL 等級/回焊峰值
  • MTBF/FIT 估算值
  • 材料內容
  • 資格摘要
  • 進行中可靠性監測
內含資訊：
  • 晶圓廠位置
  • 組裝地點

建議產品可能具有與此 TI 產品相關的參數、評估模組或參考設計。

支援與培訓

內含 TI 工程師技術支援的 TI E2E™ 論壇

以英文檢視所有論壇主題

內容係由 TI 和社群貢獻者依「現狀」提供，且不構成 TI 規範。檢視使用條款。

若有關於品質、封裝或訂購 TI 產品的問題，請參閱 TI 支援。​​​​​​​​​​​​​​

影片