SBASA22A september   2022  – july 2023 ADS131B26-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7. 6.7 Switching Characteristics
    8. 6.8 Timing Diagram
    9. 6.9 Typical Characteristics
  8. 7 Parameter Measurement Information
    1. 7.1 Offset Drift Measurement
    2. 7.2 Gain Drift Measurement
    3. 7.3 Noise Performance
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Naming Conventions
      2. 8.3.2 Precision Voltage References (REFA, REFB)
      3. 8.3.3 Clocking (MCLK, OSCM, OSCD)
      4. 8.3.4 ADC1y
        1. 8.3.4.1 ADC1y Input Multiplexer
        2. 8.3.4.2 ADC1y Programmable Gain Amplifier (PGA)
        3. 8.3.4.3 ADC1y ΔΣ Modulator
        4. 8.3.4.4 ADC1y Digital Filter
        5. 8.3.4.5 ADC1y Offset and Gain Calibration
        6. 8.3.4.6 ADC1y Conversion Data
      5. 8.3.5 ADC2y
        1. 8.3.5.1 ADC2y Input Multiplexer
        2. 8.3.5.2 ADC2y Programmable Gain Amplifier (PGA)
        3. 8.3.5.3 ADC2y ΔΣ Modulator
        4. 8.3.5.4 ADC2y Digital Filter
        5. 8.3.5.5 ADC2y Offset and Gain Calibration
        6. 8.3.5.6 ADC2y Sequencer
        7. 8.3.5.7 VCMy Buffers
        8. 8.3.5.8 ADC2y Measurement Configurations
        9. 8.3.5.9 ADC2y Conversion Data
      6. 8.3.6 ADC3y
      7. 8.3.7 General-Purpose Digital Inputs and Outputs (GPIO0 to GPIO4)
        1. 8.3.7.1 GPIOx PWM Output Configuration
        2. 8.3.7.2 GPIOx PWM Input Readback
      8. 8.3.8 General-Purpose Digital Inputs and Outputs (GPIO0A, GPIO1A, GPIO0B, GPIO1B)
      9. 8.3.9 Monitors and Diagnostics
        1. 8.3.9.1  Supply Monitors
        2. 8.3.9.2  Clock Monitors
        3. 8.3.9.3  Digital Monitors
          1. 8.3.9.3.1 Register Map CRC
          2. 8.3.9.3.2 Memory Map CRC
          3. 8.3.9.3.3 GPIO Readback
        4. 8.3.9.4  Communication Monitors
        5. 8.3.9.5  Fault Flags and Fault Masking
        6. 8.3.9.6  FAULT Pin
        7. 8.3.9.7  Diagnostics and Diagnostic Procedure
        8. 8.3.9.8  Indicators
        9. 8.3.9.9  Conversion and Sequence Counters
        10. 8.3.9.10 Supply Voltage Readback
        11. 8.3.9.11 Temperature Sensors (TSA, TSB)
        12. 8.3.9.12 Test DACs (TDACA, TDACB)
        13. 8.3.9.13 Open-Wire Detection
        14. 8.3.9.14 Missing Host Detection and MHD Pin
        15. 8.3.9.15 Overcurrent Comparators (OCCA, OCCB)
          1. 8.3.9.15.1 OCCA and OCCB Pins
          2. 8.3.9.15.2 Overcurrent Indication Response Time
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power-Up and Reset
        1. 8.4.1.1 Power-On Reset (POR)
        2. 8.4.1.2 RESETn Pin
        3. 8.4.1.3 RESET Command
      2. 8.4.2 Operating Modes
        1. 8.4.2.1 Active Mode
        2. 8.4.2.2 Standby Mode
        3. 8.4.2.3 Power-Down Mode
      3. 8.4.3 ADC Conversion Modes
        1. 8.4.3.1 ADC1y and ADC3y Conversion Modes
          1. 8.4.3.1.1 Continuous-Conversion Mode
          2. 8.4.3.1.2 Single-Shot Conversion Mode
          3. 8.4.3.1.3 Global-Chop Mode
            1. 8.4.3.1.3.1 Overcurrent Indication Response Time in Global-Chop Mode
        2. 8.4.3.2 ADC2y Sequencer Operation and Sequence Modes
          1. 8.4.3.2.1 Continuous Sequence Mode
          2. 8.4.3.2.2 Single-Shot Sequence Mode
          3. 8.4.3.2.3 Synchronized Single-Shot Sequence Mode Based on ADC1y Conversion Starts
    5. 8.5 Programming
      1. 8.5.1 Serial Interface
        1. 8.5.1.1 Serial Interface Signals
          1. 8.5.1.1.1 Chip Select (CSn)
          2. 8.5.1.1.2 Serial Data Clock (SCLK)
          3. 8.5.1.1.3 Serial Data Input (SDI)
          4. 8.5.1.1.4 Serial Data Output (SDO)
          5. 8.5.1.1.5 Data Ready (DRDYn)
        2. 8.5.1.2 Serial Interface Communication Structure
          1. 8.5.1.2.1 SPI Communication Frames
          2. 8.5.1.2.2 SPI Communication Words
          3. 8.5.1.2.3 STATUS Word
          4. 8.5.1.2.4 Communication Cyclic Redundancy Check (CRC)
          5. 8.5.1.2.5 Commands
            1. 8.5.1.2.5.1 NULL (0000 0000 0000 0000b)
            2. 8.5.1.2.5.2 RESET (0000 0000 0001 0001b)
            3. 8.5.1.2.5.3 LOCK (0000 0101 0101 0101b)
            4. 8.5.1.2.5.4 UNLOCK (0000 0110 0101 0101b)
            5. 8.5.1.2.5.5 WREG (011a aaaa aaa0 0nnnb)
            6. 8.5.1.2.5.6 RREG (101a aaaa aaan nnnnb)
          6. 8.5.1.2.6 SCLK Counter
          7. 8.5.1.2.7 SPI Timeout
          8. 8.5.1.2.8 Reading ADC1A, ADC1B, ADC2A, ADC2B, ADC3A, and ADC3B Conversion Data
          9. 8.5.1.2.9 DRDYn Pin Behavior
    6. 8.6 Register Map
      1. 8.6.1 Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
      1. 9.1.1 Unused Inputs and Outputs
      2. 9.1.2 Minimum Interface Connections
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Current-Shunt Measurement
        2. 9.2.2.2 Battery-Pack Voltage Measurement
        3. 9.2.2.3 Other Voltage Measurements
        4. 9.2.2.4 Shunt Temperature Measurement
        5. 9.2.2.5 Analog Output Temperature Sensor Measurement
      3. 9.2.3 Application Curves
    3. 9.3 Power Supply Recommendations
      1. 9.3.1 Power-Supply Options
        1. 9.3.1.1 Single Unregulated External 4-V to 16-V Supply (3.3-V Digital I/O Levels)
        2. 9.3.1.2 Single Regulated External 3.3-V Supply (3.3-V Digital IO Levels)
        3. 9.3.1.3 Single Regulated External 5-V Supply (5-V Digital I/O Levels)
      2. 9.3.2 Power-Supply Sequencing
      3. 9.3.3 Power-Supply Decoupling
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Receiving Notification of Documentation Updates
    3. 10.3 Support Resources
    4. 10.4 Trademarks
    5. 10.5 Electrostatic Discharge Caution
    6. 10.6 Glossary
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information
8.5.1.2.1 SPI Communication Frames

SPI communication on the ADS131B26-Q1 is performed in frames. Each SPI communication frame starts with a CSn falling edge, consists of several words, and ends with a CSn rising edge. The interface is full duplex, meaning that the interface is capable of transmitting data on SDO while simultaneously receiving data on SDI. Figure 8-28 provides an overview of the general SPI frame structure and frame length for the various commands.

The input frame that the host sends on SDI always begins with a command word followed by a command CRC word. The first word on the output frame that the device transmits on SDO always begins with the STATUS word. The number of words in a frame depends on the command provided. See the CommandsCommands section for a list of all valid commands on the ADS131B26-Q1.

For the NULL, RESET, LOCK, UNLOCK, and RREG commands there are six words in a frame. On SDI, the host provides the command, the command CRC, and four additional words of zeros. Simultaneously on SDO, the device outputs the STATUS word, four words of ADC data (representing the data from ADC1A, ADC1B, ADC3A, and ADC3B), and an output CRC word. Figure 8-28 shows a typical communication frame structure. In the remaining sections of this document the SCLK signal is omitted in the figures for clarity.

GUID-20211216-SS0I-QCPT-LBBJ-BFR3TGKCTMGD-low.svg Figure 8-28 Typical Communication Frame

For a write register (WREG) command where more than three registers are written, the frame extends to accommodate the additional data. See the WREG section for more details on the WREG command.

For a read register (RREG) command, the response to the command in the following frame contains the STATUS word followed by the register data requested, which can require a shorter or longer frame depending on how many registers are read. See the RREG section for more details on the RREG command.