SLVSH64B May   2026  â€“ November 2026 DRV8378

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison Table
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 SPI Timing Requirements
    7. 6.7 SPI Mode Timings
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1  Overview
    2. 7.2  Functional Block Diagram
    3. 7.3  Feature Description
      1. 7.3.1 Output Stage
      2. 7.3.2 Device Interface Modes
        1. 7.3.2.1 Serial Peripheral Interface (SPI)
        2. 7.3.2.2 Hardware Interface
      3. 7.3.3 Control Modes
        1. 7.3.3.1 3x PWM Mode (PWM_MODE = 10b or 11b or MODE_SR Pin is Connected to GVDD with RMODE or to GVDD)
        2. 7.3.3.2 6x PWM Mode (PWM_MODE = 00b or 01b or MODE_SR Pin Tied to AGND or in Hi-Z)
        3. 7.3.3.3 DRV8378G Control mode with External GVDD
      4. 7.3.4 GVDD Linear Voltage Regulator (Internal GVDD Variant)
      5. 7.3.5 Charge Pump
    4. 7.4  Slew Rate Control
    5. 7.5  Cross Conduction (Dead Time)
    6. 7.6  Propagation Delay
    7. 7.7  Pin Diagrams
      1. 7.7.1 Logic Level Input Pin (Internal Pulldown)
      2. 7.7.2 Logic Level Input Pin (Internal Pullup)
      3. 7.7.3 Open Drain Pin
      4. 7.7.4 Push Pull Pin
      5. 7.7.5 Four Level Input Pin
    8. 7.8  Current Sense Amplifiers
      1. 7.8.1 Current Sense Amplifier Operation (29-pin variant)
      2. 7.8.2 Current Sense Amplifier Operation (23-pin variant)
    9. 7.9  Active Demagnetization
      1. 7.9.1 Automatic Synchronous Rectification Mode (ASR Mode)
        1. 7.9.1.1 Automatic Synchronous Rectification in Commutation
        2. 7.9.1.2 Automatic Synchronous Rectification in PWM Mode
      2. 7.9.2 Automatic Asynchronous Rectification Mode (AAR Mode)
    10. 7.10 Cycle-by-Cycle Current Limit
      1. 7.10.1 Cycle by Cycle Current Limit with 100% Duty Cycle Input
    11. 7.11 Protections
      1. 7.11.1 Overcurrent Protection (OCP)
        1. 7.11.1.1 OCP Latched Shutdown (OCP_MODE = 00b)
        2. 7.11.1.2 OCP Automatic Retry (OCP_MODE = 01b)
        3. 7.11.1.3 OCP Disabled (OCP_MODE = 11b)
        4. 7.11.1.4 OCP Report Only (OCP_MODE = 10b)
      2. 7.11.2 VM Supply Undervoltage Lockout (RESET)
      3. 7.11.3 GVDD Undervoltage Lockout (GVDD_UV)
      4. 7.11.4 VCP Charge Pump Undervoltage Lockout (CPUV)
      5. 7.11.5 Over Voltage Protections (OV)
      6. 7.11.6 Thermal Warning (OTW)
      7. 7.11.7 Thermal Shutdown (OTS)
    12. 7.12 Device Functional Modes
      1. 7.12.1 Functional Modes
        1. 7.12.1.1 Sleep Mode
        2. 7.12.1.2 Operating Mode
        3. 7.12.1.3 Fault Reset (CLR_FLT or nSLEEP Reset Pulse)
      2. 7.12.2 DRVOFF functionality
    13. 7.13 SPI Communication
      1. 7.13.1 Programming
        1. 7.13.1.1 SPI Format
  9. 8 Register Map
    1. 8.1 CONTROL Registers
    2. 8.2 STATUS Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Power Supply Recommendations
      1. 9.2.1 Bulk Capacitance
    3. 9.3 Layout
      1. 9.3.1 Layout Guidelines
      2. 9.3.2 Layout Example
      3. 9.3.3 Thermal Considerations
        1. 9.3.3.1 Power Dissipation
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 Support Resources
    3. 10.3 Trademarks
    4. 10.4 Electrostatic Discharge Caution
    5. 10.5 Glossary
  12. 11Revision History
  13. 12Mechanical, Packaging, and Orderable Information
    1.     PACKAGE OPTION ADDENDUM
    2. 12.1 Tape and Reel Information

Package Options

Mechanical Data (Package|Pins)
  • VER|23
Thermal pad, mechanical data (Package|Pins)

STATUS Registers

Table 8-10 lists the memory-mapped registers for the STATUS registers. All register offset addresses not listed in Table 8-10 should be considered as reserved locations and the register contents should not be modified.

Table 8-10 STATUS Registers
OffsetAcronymRegister NameSection
0hDevice Status RegisterDevice Status RegisterSection 8.2.1
4hOver Temperature Status RegisterOver Temperature Status RegisterSection 8.2.2
5hSupply Status RegisterSupply Status RegisterSection 8.2.3
6hDriver Status RegisterDriver Status RegisterSection 8.2.4
7hSystem Interface Status RegisterSystem Interface Status RegisterSection 8.2.5

Complex bit access types are encoded to fit into small table cells. Table 8-11 shows the codes that are used for access types in this section.

Table 8-11 STATUS Access Type Codes
Access TypeCodeDescription
Read Type
RRRead
R-0R
-0
Read
Returns 0s
Reset or Default Value
-nValue after reset or the default value

8.2.1 Device Status Register (Offset = 0h) [Reset = 0280h]

Device Status Register is shown in Table 8-12.

Return to the Summary Table.

Table 8-12 Device Status Register Field Descriptions
BitFieldTypeResetDescription
15PARITYR0h Parity Bit if SPI_PEN is set to '1' otherwise reserved
14-11RESERVEDR-00h Reserved
10RESERVEDR0h Reserved
9DNRDY_STSR1h Device Not Ready Status. Will be cleared automatically after completion of Power Up.
  • 0h = Device is Ready
  • 1h = Device is NOT Ready
8SYSFLTR0h OTP Read fault occurred. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No OTP read fault is detected
  • 1h = OTP read fault detected
7RESETR1h Device Reset status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = Cleared by FW after read
  • 1h = Device has undergone power on reset
6SPIFLTR0h SPI Fault status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No SPI fault is detected
  • 1h = SPI fault is detected
5OCPR0h Overcurrent Status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No overcurrent condition is detected
  • 1h = Overcurrent condition is detected
4VREFEXT_UVR0h VREF EXT UVLO status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No VREF External UVLO condition is detected
  • 1h = VREF External UVLO condition is detected
3OVPR0h Over Voltage Status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No over voltage condition is detected
  • 1h = Over voltage condition is detected
2UVPR0h Supply Undervoltage Status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No undervoltage voltage condition is detected on CP
  • 1h = Undervoltage voltage condition is detected on CP
1OTFR0h Overtemperature Fault Status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No overtemperature warning / shutdown is detected
  • 1h = Overtemperature warning / shutdown is detected
0FAULTR0h Device raw Fault status.
  • 0h = No fault condition is detected
  • 1h = Fault condition is detected

8.2.2 Over Temperature Status Register (Offset = 4h) [Reset = 0000h]

Over Temperature Status Register is shown in Table 8-13.

Return to the Summary Table.

Table 8-13 Over Temperature Status Register Field Descriptions
BitFieldTypeResetDescription
15PARITYR0h Parity Bit if SPI_PEN is set to '1' otherwise reserved
14-2RESERVEDR-00h Reserved
1OTWR0h Overtemperature Warning Fault status. Can be cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No overtemperature warning is detected
  • 1h = Overtemperature warning is detected
0OTSDR0h Overtemperature Shutdown Fault status. Can be cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No overtemperature shutdown is detected
  • 1h = Overtemperature shutdown is detected

8.2.3 Supply Status Register (Offset = 5h) [Reset = 0000h]

Supply Status Register is shown in Table 8-14.

Return to the Summary Table.

Table 8-14 Supply Status Register Field Descriptions
BitFieldTypeResetDescription
15PARITYR0h Parity Bit if SPI_PEN is set to '1' otherwise reserved
14-7RESERVEDR-00h Reserved
6VM_OVR0h Vm Over Voltage Fault Status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No VM over voltage is detected
  • 1h = VM over voltage is detected
5VREFEXT_UVR0h VREF EXT UVLO status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No VREF External UVLO condition is detected
  • 1h = VREF External UVLO condition is detected
4CP_UVR0h Charge Pump Undervoltage fault status. Status remains latched until cleared by write to FLT_CLR or reset pulse on nSLEEP
  • 0h = No charge pump undervoltage is detected
  • 1h = Charge pump undervoltage is detected
3-0RESERVEDR-00h Reserved

8.2.4 Driver Status Register (Offset = 6h) [Reset = 0000h]

Driver Status Register is shown in Table 8-15.

Return to the Summary Table.

Table 8-15 Driver Status Register Field Descriptions
BitFieldTypeResetDescription
15PARITYR0h Parity Bit if SPI_PEN is set to '1' otherwise reserved
14-13RESERVEDR-00h Reserved
12W_LS_GATE_LOR0h W phase low side gate signal status
  • 0h = W phase LS FET is ON
  • 1h = W phase LS FET is OFF
11V_LS_GATE_LOR0h V phase low side gate signal status
  • 0h = V phase LS FET is ON
  • 1h = V phase LS FET is OFF
10U_LS_GATE_LOR0h U phase low side gate signal status
  • 0h = U phase LS FET is ON
  • 1h = U phase LS FET is OFF
9W_HS_GATE_LOR0h W phase high side gate signal status
  • 0h = W phase HS FET is ON
  • 1h = W phase HS FET is OFF
8V_HS_GATE_LOR0h V phase high side gate signal status
  • 0h = V phase HS FET is ON
  • 1h = V phase HS FET is OFF
7U_HS_GATE_LOR0h U phase high side gate signal status
  • 0h = U phase HS FET is ON
  • 1h = U phase HS FET is OFF
6OCPC_HSR0h Overcurrent Status on High-side switch of OUTC
  • 0h = No overcurrent detected on high-side MOSFET of OUTC
  • 1h = Overcurrent detected on high-side MOSFET of OUTC
5OCPB_HSR0h Overcurrent Status on High-side switch of OUTB
  • 0h = No overcurrent detected on high-side MOSFET of OUTB
  • 1h = Overcurrent detected on high-side MOSFET of OUTB
4OCPA_HSR0h Overcurrent Status on High-side switch of OUTA
  • 0h = No overcurrent detected on high-side MOSFET of OUTA
  • 1h = Overcurrent detected on high-side MOSFET of OUTA
3RESERVEDR-00h Reserved
2OCPC_LSR0h Overcurrent Status on Low-side switch of OUTC
  • 0h = No overcurrent detected on low-side MOSFET of OUTC
  • 1h = Overcurrent detected on low-side MOSFET of OUTC
1OCPB_LSR0h Overcurrent Status on Low-side switch of OUTB
  • 0h = No overcurrent detected on low-side MOSFET of OUTB
  • 1h = Overcurrent detected on low-side MOSFET of OUTB
0OCPA_LSR0h Overcurrent Status on Low-side switch of OUTA
  • 0h = No overcurrent detected on low-side MOSFET of OUTA
  • 1h = Overcurrent detected on low-side MOSFET of OUTA

8.2.5 System Interface Status Register (Offset = 7h) [Reset = 0000h]

System Interface Status Register is shown in Table 8-16.

Return to the Summary Table.

Table 8-16 System Interface Status Register Field Descriptions
BitFieldTypeResetDescription
15PARITYR0h Parity Bit if SPI_PEN is set to '1' otherwise reserved
14-5RESERVEDR-00h Reserved
4RESERVEDR0h Reserved
3RESERVEDR0h Reserved
2SPI_PARITYR0h SPI Parity Error
  • 0h = No SPI Parity Error is detected
  • 1h = SPI Parity Error is detected
1RESERVEDR-00h Reserved
0FRM_ERRR0h SPI Frame Error
  • 0h = No SPI Frame Error is detected
  • 1h = SPI Frame Error is detected