SNVSCE1B May   2023  – November 2023 LP5860T

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Timing Requirements
    7.     14
    8. 6.7 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Time-Multiplexing Matrix
      2. 7.3.2 Analog Dimming (Current Gain Control)
        1. 7.3.2.1 Global 3-Bits Maximum Current (MC) Setting
        2. 7.3.2.2 3 Groups of 7-Bits Color Current (CC) Setting
        3. 7.3.2.3 Individual 8-bit Dot Current (DC) Setting
      3. 7.3.3 PWM Dimming
        1. 7.3.3.1 Individual 8-Bit / 16-Bit PWM for Each LED Dot
        2. 7.3.3.2 Programmable Groups of 8-Bit PWM Dimming
        3. 7.3.3.3 8-Bit PWM for Global Dimming
      4. 7.3.4 ON and OFF Control
      5. 7.3.5 Data Refresh Mode
      6. 7.3.6 Full Addressable SRAM
      7. 7.3.7 Protections and Diagnostics
        1. 7.3.7.1 LED Open Detection
        2. 7.3.7.2 LED Short Detection
        3. 7.3.7.3 Thermal Shutdown
        4. 7.3.7.4 UVLO (Under Voltage Lock Out)
    4. 7.4 Device Functional Modes
    5. 7.5 Programming
      1. 7.5.1 Interface Selection
      2. 7.5.2 I2C Interface
        1. 7.5.2.1 I2C Data Transactions
        2. 7.5.2.2 I2C Data Format
        3. 7.5.2.3 Multiple Devices Connection
      3. 7.5.3 Programming
        1. 7.5.3.1 SPI Data Transactions
        2. 7.5.3.2 SPI Data Format
        3. 7.5.3.3 Multiple Devices Connection
    6. 7.6 Register Maps
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Program Procedure
      4. 8.2.4 Application Performance Plots
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 VDD Input Supply Recommendations
      2. 8.3.2 VLED Input Supply Recommendations
      3. 8.3.3 VIO Input Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.5.2.3 Multiple Devices Connection

The LP5860T enters into I2C mode if IFS is connected to GND. The ADDR0/1 pin is used to select the unique I2C follower address for each device. The SCL and SDA lines must each have a pullup resistor (4.7KΩ for 400KHz, 2KΩ for 1MHz) placed somewhere on the line and remain HIGH even when the bus is idle. VIO_EN can either be connected with VIO power supply or GPIO. It’s suggested to put one 1nF cap as closer to VIO_EN pin as possible. Up to four LP5860T follower devices can share the same I2C bus by the different ADDR configurations.

GUID-6B149CD0-C651-4E57-9704-DE4A42162C33-low.svg Figure 7-16 I2C Multiple Devices Connection