SLLSEV1C September   2017  – December 2018 THVD1510 , THVD1512 , THVD1550 , THVD1551 , THVD1552

PRODUCTION DATA.  

  1. Features
  2. Applications
  3. Description
    1.     Device Images
      1.      THVD1510 and THVD1550 Simplified Schematic
      2.      THVD1551 Simplified Schematic
      3.      THVD1512 and THVD1552 Simplified Schematic
  4. Revision History
  5. Device Comparison Table
  6. Pin Configuration and Functions
    1.     Pin Functions
    2.     Pin Functions
    3.     Pin Functions
  7. Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Power Dissipation
    6. 7.6 Electrical Characteristics
    7. 7.7 Switching Characteristics
    8. 7.8 Switching Characteristics
    9. 7.9 Typical Characteristics
  8. Parameter Measurement Information
  9. Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagrams
    3. 9.3 Feature Description
    4. 9.4 Device Functional Modes
      1. 9.4.1 Device Functional Modes for THVD1510 and THVD1550
      2. 9.4.2 Device Functional Modes for THVD1551
      3. 9.4.3 Device Functional Modes for THVD1512 and THVD1552
  10. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
        1. 10.2.1.1 Data Rate and Bus Length
        2. 10.2.1.2 Stub Length
        3. 10.2.1.3 Bus Loading
        4. 10.2.1.4 Receiver Failsafe
        5. 10.2.1.5 Transient Protection
      2. 10.2.2 Detailed Design Procedure
      3. 10.2.3 Application Curves
  11. 11Power Supply Recommendations
  12. 12Layout
    1. 12.1 Layout Guidelines
    2. 12.2 Layout Example
  13. 13Device and Documentation Support
    1. 13.1 Device Support
    2. 13.2 Third-Party Products Disclaimer
    3. 13.3 Related Links
    4. 13.4 Receiving Notification of Documentation Updates
    5. 13.5 Community Resources
    6. 13.6 Trademarks
    7. 13.7 Electrostatic Discharge Caution
    8. 13.8 Glossary
  14. 14Mechanical, Packaging, and Orderable Information

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • D|8
  • DGK|8
Thermal pad, mechanical data (Package|Pins)
Orderable Information

Electrical Characteristics

over operating free-air temperature range (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Driver
|VOD| Driver differential output voltage magnitude RL = 60 Ω, -15 V ≤ Vtest ≤ 15 V, (See Figure 11) 1.5 2.7 V
RL = 100 Ω (See Figure 12) 2 3 V
RL = 54 Ω (See Figure 12) 1.5 2.7 V
Δ|VOD| Change in differential output voltage RL = 54 Ω (See Figure 12) –200 200 mV
VOC Common-mode output voltage 1 VCC/2 3 V
ΔVOC(SS) Change in steady-state common-mode output voltage –200 200 mV
IOS Short-circuit output current DE = VCC, -15 V ≤ VO ≤ 15V –250 250 mA
Receiver
II Bus input current DE = 0 V, VCC = 0 V or 5.5 V THVD151x VI = 12 V 75 125 μA
VI = 15 V 95 156
VI = -7 V -100 -40
VI = -15 V -215 -85
THVD155x VI = 12 V 115 160
VI = 15 V 150 200
VI = -7 V -130 -75
VI = -15 V -280 -180
Receiver
VTH+ Positive-going input threshold voltage Over common-mode range of - 7 V to +12 V See(1) –85 –20 mV
VTH- Negative-going input threshold voltage –200 –135 See(1) mV
VHYS Input hysteresis 50 mV
VTH+ Positive-going input threshold voltage Over common-mode range of ± 15 V See(1) –85 –20 mV
VTH- Negative-going input threshold voltage –220 –135 See(1) mV
VHYS Input hysteresis 50 mV
VOH Output high voltage IOH = -8 mA 4 VCC - 0.3 V
VOL Output low voltage IOL = 8 mA 0.2 0.4 V
IOZ Output high-impedance current VO = 0 V or VCC, RE = VCC -1 1 µA
Logic
IIN Input current (D, DE, RE) 4.5 V ≤ VCC ≤ 5.5 V, 0 V ≤ VIN ≤ VCC –5 0 5 µA
Supply
ICC Supply current (quiescent) Driver and receiver enabled RE = 0 V, DE = VCC, No load 700 1000 µA
Driver enabled, receiver disabled RE = VCC, DE = VCC, No load 400 620 µA
Driver disabled, receiver enabled RE = 0 V, DE = 0 V, No load 400 630 µA
Driver and receiver disabled RE = VCC, DE = 0 V, D = open, No load 0.1 1 µA
TSD Thermal shutdown temperature 170 °C
Under any specific conditions, VTH+ is specified to be at least VHYS higher than VTH–.