SLVSMM5 October   2026 TMCS1236-Q1

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Power Ratings
    6. 6.6  Insulation Specifications
    7. 6.7  Safety-Related Certifications
    8. 6.8  Safety Limiting Values
    9. 6.9  Electrical Characteristics
    10. 6.10 Typical Characteristics
      1. 6.10.1 Insulation Characteristics Curves
  8. 7 Parameter Measurement Information
    1. 7.1 Accuracy Parameters
      1. 7.1.1 Sensitivity Error
      2. 7.1.2 Offset Error and Offset Error Drift
      3. 7.1.3 Nonlinearity Error
      4. 7.1.4 Power Supply Rejection Ratio
      5. 7.1.5 Common-Mode Rejection Ratio
      6. 7.1.6 Optional Filter for Reduced Bandwidth and Noise
    2. 7.2 Transient Response Parameters
      1. 7.2.1 CMTI, Common-Mode Transient Immunity
    3. 7.3 Safe Operating Area
      1. 7.3.1 Continuous DC or Sinusoidal AC Current
      2. 7.3.2 Repetitive Pulsed Current SOA
      3. 7.3.3 Single Event Current Capability
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Current Input
      2. 8.3.2 Input Isolation
      3. 8.3.3 Ambient Field Rejection
      4. 8.3.4 High-Precision Signal Chain
        1. 8.3.4.1 Temperature Stability
      5. 8.3.5 Internal Reference Voltage
      6. 8.3.6 Current-Sensing Measurable Ranges
      7. 8.3.7 Overcurrent Detection
        1. 8.3.7.1 Setting The User Configurable Overcurrent Threshold
          1. 8.3.7.1.1 Setting Overcurrent Threshold Using Power Supply Voltage
          2. 8.3.7.1.2 Setting Overcurrent Threshold Example
        2. 8.3.7.2 Overcurrent Output Response
        3. 8.3.7.3 Overcurrent Detection MASK Time
    4. 8.4 Device Functional Modes
      1. 8.4.1 Power-Down Behavior
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Consideration
      2. 9.2.2 Application Curve
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1.     PACKAGE OPTION ADDENDUM
    2. 11.1 Tape and Reel Information
    3. 11.2 Mechanical Data

Refer to the PDF data sheet for device specific package drawings

Design Consideration

Intermodulation distortion is a distortion product that arises when signals are applied to the input of a non-linear circuit utilizing a chopping topology, creating undesired frequency products that can interfere with the desired signal. The switching frequency of the chopping clock can interact with the frequency content of the input signal. To minimize this effect, in the TMCS1236-Q1 the internal oscillator frequency is increased to 1.1MHz, to enable operation with higher switching frequencies.

TMCS1236-Q1 Distortion Over
                    Frequency Figure 9-2 Distortion Over Frequency

The TMCS1236-Q1 employs a chopping signal chain to achieve low offset. A well-known characteristic of chopped architectures is that the periodic switching action of the internal chopper introduces intermodulation between the clock frequency (fCLK) and the spectral content of the input signal. When the input current contains spectral energy near the chopper frequency or clock harmonics, mixing products are generated at frequencies |n x fCLK +/- fIN| for integer n. These tones can appear within the measurement band if not accounted for in the system frequency plan. To place the dominant intermodulation tones well above the signal frequencies of typical power-conversion applications, the internal oscillator is designed to operate at 1.1MHz. For distoration-sensitive application, Figure 9-2 characterizes THD versus input frequency for the 132mV/A device variant at 45% full-scale input. System designers should select an operating frequency plan that maintains adequate spectral separation and design margin between the input signal and the clock frequency and its harmonics. Additionally, the internal oscillator frequency is subject to normal process, voltage, and temperature variation.