SLVSF02E march   2019  – may 2023 TPS23881

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
    1. 6.1 Detailed Pin Description
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Electrical Characteristics
    6. 7.6 Typical Characteristics
  9. 8 Parameter Measurement Information
    1. 8.1 Timing Diagrams
  10. 9 Detailed Description
    1. 9.1 Overview
      1. 9.1.1 Operating Modes
        1. 9.1.1.1 Auto
        2. 9.1.1.2 Semiauto
        3. 9.1.1.3 Manual and Diagnostic
        4. 9.1.1.4 Power Off
      2. 9.1.2 PoE Compliance Terminology
      3. 9.1.3 Channel versus Port Terminology
      4. 9.1.4 Requested Class versus Assigned Class
      5. 9.1.5 Power Allocation and Power Demotion
      6. 9.1.6 Programmable SRAM
    2. 9.2 Functional Block Diagram
    3. 9.3 Feature Description
      1. 9.3.1 Port Remapping
      2. 9.3.2 Port Power Priority
      3. 9.3.3 Analog-to-Digital Converters (ADC)
      4. 9.3.4 I2C Watchdog
      5. 9.3.5 Current Foldback Protection
    4. 9.4 Device Functional Modes
      1. 9.4.1 Detection
      2. 9.4.2 Connection Check
      3. 9.4.3 Classification
      4. 9.4.4 DC Disconnect
    5. 9.5 I2C Programming
      1. 9.5.1 I2C Serial Interface
    6. 9.6 Register Maps
      1. 9.6.1 Complete Register Set
      2. 9.6.2 Detailed Register Descriptions
        1. 9.6.2.1  INTERRUPT Register
        2. 9.6.2.2  INTERRUPT MASK Register
        3. 9.6.2.3  POWER EVENT Register
        4. 9.6.2.4  DETECTION EVENT Register
        5. 9.6.2.5  FAULT EVENT Register
        6. 9.6.2.6  START/ILIM EVENT Register
        7. 9.6.2.7  SUPPLY and FAULT EVENT Register
          1. 9.6.2.7.1 Detected SRAM Faults and "Safe Mode"
            1. 9.6.2.7.1.1 ULA (Ultra Low Alpha) Package Option: TPS23881A
        8. 9.6.2.8  CHANNEL 1 DISCOVERY Register
        9. 9.6.2.9  CHANNEL 2 DISCOVERY Register
        10. 9.6.2.10 CHANNEL 3 DISCOVERY Register
        11. 9.6.2.11 CHANNEL 4 DISCOVERY Register
        12. 9.6.2.12 POWER STATUS Register
        13. 9.6.2.13 PIN STATUS Register
        14. 9.6.2.14 OPERATING MODE Register
        15. 9.6.2.15 DISCONNECT ENABLE Register
        16. 9.6.2.16 DETECT/CLASS ENABLE Register
        17. 9.6.2.17 Power Priority / 2Pair PCUT Disable Register Name
        18. 9.6.2.18 TIMING CONFIGURATION Register
        19. 9.6.2.19 GENERAL MASK Register
        20. 9.6.2.20 DETECT/CLASS RESTART Register
        21. 9.6.2.21 POWER ENABLE Register
        22. 9.6.2.22 RESET Register
        23. 9.6.2.23 ID Register
        24. 9.6.2.24 Connection Check and Auto Class Status Register
        25. 9.6.2.25 2-Pair Police Ch-1 Configuration Register
        26. 9.6.2.26 2-Pair Police Ch-2 Configuration Register
        27. 9.6.2.27 2-Pair Police Ch-3 Configuration Register
        28. 9.6.2.28 2-Pair Police Ch-4 Configuration Register
        29. 9.6.2.29 Capacitance (Legacy PD) Detection
        30. 9.6.2.30 Power-on Fault Register
        31. 9.6.2.31 PORT RE-MAPPING Register
        32. 9.6.2.32 Channels 1 and 2 Multi Bit Priority Register
        33. 9.6.2.33 Channels 3 and 4 Multi Bit Priority Register
        34. 9.6.2.34 4-Pair Wired and Port Power Allocation Register
        35. 9.6.2.35 4-Pair Police Ch-1 and 2 Configuration Register
        36. 9.6.2.36 4-Pair Police Ch-3 and 4 Configuration Register
        37. 9.6.2.37 TEMPERATURE Register
        38. 9.6.2.38 4-Pair Fault Configuration Register
        39. 9.6.2.39 INPUT VOLTAGE Register
        40. 9.6.2.40 CHANNEL 1 CURRENT Register
        41. 9.6.2.41 CHANNEL 2 CURRENT Register
        42. 9.6.2.42 CHANNEL 3 CURRENT Register
        43. 9.6.2.43 CHANNEL 4 CURRENT Register
        44. 9.6.2.44 CHANNEL 1 VOLTAGE Register
        45. 9.6.2.45 CHANNEL 2 VOLTAGE Register
        46. 9.6.2.46 CHANNEL 3 VOLTAGE Register
        47. 9.6.2.47 CHANNEL 4 VOLTAGE Register
        48. 9.6.2.48 2x FOLDBACK SELECTION Register
        49. 9.6.2.49 FIRMWARE REVISION Register
        50. 9.6.2.50 I2C WATCHDOG Register
        51. 9.6.2.51 DEVICE ID Register
        52. 9.6.2.52 CHANNEL 1 DETECT RESISTANCE Register
        53. 9.6.2.53 CHANNEL 2 DETECT RESISTANCE Register
        54. 9.6.2.54 CHANNEL 3 DETECT RESISTANCE Register
        55. 9.6.2.55 CHANNEL 4 DETECT RESISTANCE Register
        56. 9.6.2.56 CHANNEL 1 DETECT CAPACITANCE Register
        57. 9.6.2.57 CHANNEL 2 DETECT CAPACITANCE Register
        58. 9.6.2.58 CHANNEL 3 DETECT CAPACITANCE Register
        59. 9.6.2.59 CHANNEL 4 DETECT CAPACITANCE Register
        60. 9.6.2.60 CHANNEL 1 ASSIGNED CLASS Register
        61. 9.6.2.61 CHANNEL 2 ASSIGNED CLASS Register
        62. 9.6.2.62 CHANNEL 3 ASSIGNED CLASS Register
        63. 9.6.2.63 CHANNEL 4 ASSIGNED CLASS Register
        64. 9.6.2.64 AUTO CLASS CONTROL Register
        65. 9.6.2.65 CHANNEL 1 AUTO CLASS POWER Register
        66. 9.6.2.66 CHANNEL 2 AUTO CLASS POWER Register
        67. 9.6.2.67 CHANNEL 3 AUTO CLASS POWER Register
        68. 9.6.2.68 CHANNEL 4 AUTO CLASS POWER Register
        69. 9.6.2.69 ALTERNATIVE FOLDBACK Register
        70. 9.6.2.70 SRAM CONTROL Register
          1. 9.6.2.70.1 SRAM START ADDRESS (LSB) Register
          2. 9.6.2.70.2 SRAM START ADDRESS (MSB) Register
  11. 10Application and Implementation
    1. 10.1 Application Information
      1. 10.1.1 Introduction to PoE
        1. 10.1.1.1 2-Pair Versus 4-Pair Power and the New IEEE802.3bt Standard
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Connections on Unused Channels
        2. 10.2.2.2 Power Pin Bypass Capacitors
        3. 10.2.2.3 Per Port Components
        4. 10.2.2.4 System Level Components (not Shown in the Schematic Diagrams)
      3. 10.2.3 Application Curves
  12. 11Power Supply Recommendations
    1. 11.1 VDD
    2. 11.2 VPWR
  13. 12Layout
    1. 12.1 Layout Guidelines
      1. 12.1.1 Kelvin Current Sensing Resistors
    2. 12.2 Layout Example
      1. 12.2.1 Component Placement and Routing Guidelines
        1. 12.2.1.1 Power Pin Bypass Capacitors
        2. 12.2.1.2 Per-Port Components
  14. 13Device and Documentation Support
    1. 13.1 Documentation Support
      1. 13.1.1 Related Documentation
    2. 13.2 Receiving Notification of Documentation Updates
    3. 13.3 Support Resources
    4. 13.4 Trademarks
    5. 13.5 Electrostatic Discharge Caution
    6. 13.6 Glossary
  15. 14Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

9.6.2.28 2-Pair Police Ch-4 Configuration Register

COMMAND = 21h with 1 Data Byte, Read/Write

Figure 9-35 2-Pair Police Ch-4 Register Format
76543210
POL4_7POL4_6POL4_5POL4_4POL4_3POL4_2POL4_1POL4_0
R/W-1R/W-1R/W-1R/W-1R/W-1R/W-1R/W-1R/W1
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 9-36 2-Pair Policing Register Fields Descriptions
BitFieldTypeResetDescription
7–0POLn_7- POLn_0R/W11-byte defining 2-Pair PCUTminimum threshold.

The equation defining the PCUT is:

PCUT = (N × PCSTEP)

Where, when assuming 0.200-Ω Rsense resistor is used:

PCSTEP = 0.5 W

Note:

These bits set the minimum threshold for the design. Internally, the typical PCUT threshold is set slightly above this value to ensure that the device does not trip a Pcut fault at or below the set value in this register due to part to part or temperature variation.

For 4-pair wired ports, the 2P Policing values are still applied to the individual channels. See the description for registers 0x2Ah and 0x2Bh for more information on 4-Pair Policing.

The contents of this register is reset to 0xFFh anytime the port is turned off or disabled either due to fault condition or user command

Note:

Programmed values of less than 2W are not supported. If a value of less than 2W is programmed into these registers, the device will use 2W as the 2-pair Policing value.

Power Policing:

The TPS23881 implements a true Power Policing limit, where the device will adjust the policing limit based on both voltage and current variation in order to ensure a reliable power limit.

In Semi Auto and Auto modes, these bits are automatically set during power on based on the assigned class (see tables below). If an alternative value is desired, it needs to be set after the PEn bit is set in 0x10h, or it may also be configured prior to port turn on in combination with the use of the MPOLn bits in register 0x40 (see Section 9.6.2.48).

Table 9-37 2-Pair Policing Settings for 2-Pair Wired Ports and 4-Pair Dual Signature Devices
Assigned ClassPOLn7-0 SettingsMinimum Power
Class 10000 10004W
Class 20000 11107W
Class 30001 111115.5W
Class 40011 110030W
Class 5 Dual Signature0101 101045W
Table 9-38 2-Pair Policing Settings for 4-Pair Wired Port with Single Signature Devices
Assigned ClassPOLn7-0 SettingsMinimum Power
Class 10000 10004W(1)
Class 20000 11107W(1)
Class 30001 111115.5W(1)
Class 40011 110030W(1)
Class 50100 000032W(2)
Class 60100 111039W(2)
Class 70101 100144.5W(2)
Class 80110 101153.5W(2)
(1) Both channels of a 4-Pair port with a single signature device and an assigned class of 1-4 are required to support the full classification current per pair set.
(2) 4-Pair ports with a single signature device and an assigned class of 5-8 are required to satisfy the IEEE load imbalance requirements for 4-Pair powered devices.