SLVSGD3A december   2022  – june 2023 TPS281C30

PRODUCTION DATA  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Revision History
  6. 5 Device Comparison Table
  7. 6 Pin Configuration and Functions
  8. 7 Specifications
    1. 7.1 Absolute Maximum Ratings
    2. 7.2 ESD Ratings
    3. 7.3 Recommended Operating Conditions
    4. 7.4 Thermal Information
    5. 7.5 Thermal Information
    6. 7.6 Electrical Characteristics
    7. 7.7 SNS Timing Characteristics
    8. 7.8 Switching Characteristics
    9. 7.9 Typical Characteristics
  9. 8 Parameter Measurement Information
  10. 9 Detailed Description
    1. 9.1 Overview
    2. 9.2 Functional Block Diagram
    3. 9.3 Device Functional Modes
      1. 9.3.1 Working Mode
    4. 9.4 Feature Description
      1. 9.4.1 Accurate Current Sense
        1. 9.4.1.1 High Accuracy Sense Mode
      2. 9.4.2 Programmable Current Limit
        1. 9.4.2.1 Short-Circuit and Overload Protection
        2. 9.4.2.2 Capacitive Charging
      3. 9.4.3 Inductive-Load Switching-Off Clamp
      4. 9.4.4 Inductive Load Demagnetization
      5. 9.4.5 Full Protections and Diagnostics
        1. 9.4.5.1 Open-Load Detection
        2. 9.4.5.2 Thermal Protection Behavior
        3. 9.4.5.3 Undervoltage Lockout (UVLO) Protection
        4. 9.4.5.4 Overvoltage (OVP) Protection
        5. 9.4.5.5 Reverse Polarity Protection
        6. 9.4.5.6 Protection for MCU I/Os
        7. 9.4.5.7 Diagnostic Enable Function
        8. 9.4.5.8 Loss of Ground
  11. 10Application and Implementation
    1. 10.1 Application Information
    2. 10.2 Typical Application
      1. 10.2.1 Design Requirements
        1. 10.2.1.1 IEC 61000-4-5 Surge
      2. 10.2.2 Detailed Design Procedure
        1. 10.2.2.1 Selecting RILIM
        2. 10.2.2.2 Selecting RSNS
    3. 10.3 Power Supply Recommendations
    4. 10.4 Layout
      1. 10.4.1 Layout Guidelines
        1. 10.4.1.1 EMC Considerations
      2. 10.4.2 Layout Example
        1. 10.4.2.1 PWP Layout without a GND Network
        2. 10.4.2.2 PWP Layout with a GND Network
        3. 10.4.2.3 RGW Layout with a GND Network
      3. 10.4.3 Thermal Considerations
  12. 11Device and Documentation Support
    1. 11.1 Receiving Notification of Documentation Updates
    2. 11.2 Support Resources
    3. 11.3 Trademarks
    4. 11.4 Electrostatic Discharge Caution
    5. 11.5 Glossary
  13. 12Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.1 Absolute Maximum Ratings

Over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Continuous supply voltage, VS with respect to IC GND: Version A, B -0.7 64 V
Continuous supply voltage, VOUT with respect to IC GND: Version A, B -60 64 V
Transient (< 100 us) voltage at the supply pin, VS  with respect to IC GND: Version A, B -0.7 81 V
Continuous supply voltage, VS with respect to IC GND: Version C, D -0.7 81 V
Continuous supply voltage, VOUT with respect to IC GND: Version C, D -60 81 V
Continuous voltage across the VS and VOUT pins (VS -  VOUT ):  Version C, D -0.7 81 V
Enable pin voltage, VEN –1 6 V
OL_ON pin voltage,  VOL_ON –1 6 V
DIAG_EN pin voltage, VDIAG_EN –1 6 V
Sense pin voltage, VSNS –1 6 V
FAULT pin voltage, VFAULT –1 6 V
Reverse ground current, IGND VS < 0 V –50 mA
Maximum junction temperature, TJ 150 °C
Storage temperature, Tstg –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute maximum rated conditions for extended periods may affect device reliability.