SLVSGM2 March   2023 TPS548C26

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Internal VCC LDO and Using an External Bias on VCC and VDRV Pin
      2. 7.3.2  Input Undervoltage Lockout (UVLO)
        1. 7.3.2.1 Fixed VCC_OK UVLO
        2. 7.3.2.2 Fixed VDRV UVLO
        3. 7.3.2.3 Fixed PVIN UVLO
        4. 7.3.2.4 Enable
      3. 7.3.3  Set the Output Voltage
      4. 7.3.4  Differential Remote Sense and Feedback Divider
      5. 7.3.5  Start-up and Shutdown
      6. 7.3.6  Loop Compensation
      7. 7.3.7  Set Switching Frequency and Operation Mode
      8. 7.3.8  Switching Node (SW)
      9. 7.3.9  Overcurrent Limit and Low-side Current Sense
      10. 7.3.10 Negative Overcurrent Limit
      11. 7.3.11 Zero-Crossing Detection
      12. 7.3.12 Input Overvoltage Protection
      13. 7.3.13 Output Undervoltage and Overvoltage Protection
      14. 7.3.14 Overtemperature Protection
      15. 7.3.15 Power Good
    4. 7.4 Device Functional Modes
      1. 7.4.1 Forced Continuous-Conduction Mode
      2. 7.4.2 Auto-Skip Eco-mode Light Load Operation
      3. 7.4.3 Powering the Device from a 12-V Bus
      4. 7.4.4 Powering the Device From a Split-rail Configuration
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Application
      2. 8.2.2 Design Requirements
      3. 8.2.3 Detailed Design Procedure
        1. 8.2.3.1 Inductor Selection
        2. 8.2.3.2 Input Capacitor Selection
        3. 8.2.3.3 Output Capacitor Selection
        4. 8.2.3.4 VCC and VRDV Bypass Capacitor
        5. 8.2.3.5 BOOT Capacitor Selection
        6. 8.2.3.6 PG Pullup Resistor Selection
      4. 8.2.4 Application Curves
    3. 8.3 Power Supply Recommendations
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Example
        1. 8.4.2.1 Thermal Performance on TPS548C26 Evaluation Board
  9. 9 Device and Documentation Support
    1. 9.1 Receiving Notification of Documentation Updates
    2. 9.2 Support Resources
    3. 9.3 Trademarks
    4. 9.4 Electrostatic Discharge Caution
    5. 9.5 Glossary
  10. 10Mechanical, Packaging, and Orderable Information

Package Options

Mechanical Data (Package|Pins)
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.3.3 Set the Output Voltage

The output voltage is programmed by the FB voltage divider resistors, RFB_top and RFB_bot. Connect RFB_top between the FB pin and the positive node of the load, and connect RFB_bot between the FB pin and GOSNS pin. The recommended RFB_bot value is 10 kΩ, ranging from 1 kΩ to 20 kΩ. Determine RFB_top by using the below equation:

Equation 1. R F B _ t o p = V O U T - V I N T R E F V I N T R E F - R F B _ b o t

Where

  • VOUT is the desired output voltage in V.
  • VINTREF is 0.8 V.

To achieve the overall VOUT accuracy, using ±1% or better accuracy resistor for the FB voltage divider is highly recommended.

The output voltage sensed on the VOSNS pin is fed into the internal on-time generation circuitry. TI recommends shorting the VOSNS pin directly to VOUT sense point (that is, where the RFB_top is connected). Adding any resistance higher than 51 Ω between VOUT sense point and the VOSNS pin shifts switching frequency higher than the desired setting. Contact Texas Instruments if a resistor has to be placed between VOUT sense point and the VOSNS pin.