SLUSFP1B April   2025  – November 2025 UCC34141-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 Features
  3. 2 Applications
  4. 3 Description
  5. 4 Device Comparison
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Insulation Specifications
    6. 6.6 Electrical Characteristics
    7. 6.7 Safety-Related Certifications
    8. 6.8 Typical Characteristics
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Power Stage Operation
        1. 7.3.1.1 VDD-COM Voltage Regulation
        2. 7.3.1.2 COM-VEE Voltage Regulation
        3. 7.3.1.3 COM-VEE Output Capability
      2. 7.3.2 Output Voltage Soft Start
      3. 7.3.3 ENA and Power-Good
      4. 7.3.4 Protection Functions
        1. 7.3.4.1 Input Undervoltage Lockout
        2. 7.3.4.2 Input Overvoltage Lockout
        3. 7.3.4.3 Output Undervoltage Protection
        4. 7.3.4.4 Output Overvoltage Protection
        5. 7.3.4.5 Over-Temperature Protection
        6. 7.3.4.6 BSW Pin Faults Protection
    4. 7.4 Device Functional Modes
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 VDD-COM Voltage Regulation
        2. 8.2.2.2 COM-VEE Voltage Regulation and Single Output Configuration
    3. 8.3 System Examples
    4. 8.4 Power Supply Recommendations
    5. 8.5 Layout
      1. 8.5.1 Layout Guidelines
      2. 8.5.2 Layout Example
  10. 9 Device and Documentation Support
    1. 9.1 Third-Party Products Disclaimer
    2. 9.2 Documentation Support
      1. 9.2.1 Related Documentation
    3. 9.3 Receiving Notification of Documentation Updates
    4. 9.4 Support Resources
    5. 9.5 Trademarks
    6. 9.6 Electrostatic Discharge Caution
    7. 9.7 Glossary
  11. 10Revision History
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Packaging Information
    2. 11.2 Tape and Reel Information
    3. 11.3 Mechanical Data

Package Options

Refer to the PDF data sheet for device specific package drawings

Mechanical Data (Package|Pins)
  • DHA|16
Thermal pad, mechanical data (Package|Pins)
Orderable Information

7.3.4 Protection Functions

UCC34141-Q1 is equipped with a full feature of protection functions, including input undervoltage lockout, overvoltage lockout, output undervoltage, overvoltage, and over-temperature. The input undervoltage and overvoltage lockout protections have an auto recovery response. All other protections have a fault response based on the part number as listed in Table 4-1. For the latch-off-response, protections are triggered, the converter enters a latch-off state, and stops switching. The latch is reset by either toggling the ENA pin Off then On, or by lowering the VVIN voltage below the VVIN_UVLO_F threshold, and then above the VVIN_UVLO_R threshold. For auto-restart response, once the part shuts down, a tRESTART timer will start and then the part will attempt an auto-restart with a new soft-start sequence as shown in Figure 7-11. If the fault has been removed, the part will soft-start to regulation successfullly. If the fault condition remains, the part will shut down again and attempt another auto-restart. The device can continuously operate safely in hiccup mode as long as the fault occurs.

UCC34141-Q1 Auto-Restart Operation with PG Active High Figure 7-11 Auto-Restart Operation with PG Active High