JAJSOU6 October   2023 TPS2HCS10-Q1

ADVANCE INFORMATION  

  1.   1
  2. 1 特長
  3. 2 アプリケーション
  4. 3 概要
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
    1. 5.1 Recommended Connections for Unused Pins
  7. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 SPI Timing Requirements
    7. 6.7 Switching Characteristics
  8. 7 Parameter Measurement Information
  9. 8 Detailed Description
    1. 8.1 Overview
    2. 8.2 Functional Block Diagram
    3. 8.3 Feature Description
      1. 8.3.1 Protection Mechanisms
        1. 8.3.1.1 Programmable Fuse Protection
        2. 8.3.1.2 Thermal Shutdown
        3. 8.3.1.3 Overcurrent Protection And Capacitive Load Charging
        4. 8.3.1.4 Reverse Battery
      2. 8.3.2 Diagnostic Mechanisms
        1. 8.3.2.1 VOUT Short-to-Battery and Open-Load
          1. 8.3.2.1.1 Detection With Channel Output (FET) Enabled
          2. 8.3.2.1.2 Detection With Channel Output Disabled
        2. 8.3.2.2 Digital Current Sense Output
          1. 8.3.2.2.1 RSNS Value and Accuracy / Resolution of Current Measurement
            1. 8.3.2.2.1.1 High Accuracy Load Current Sense
            2. 8.3.2.2.1.2 SNS Output Filter
        3. 8.3.2.3 Output Voltage and FET Temperature Sensing
    4. 8.4 Device Functional Modes
      1. 8.4.1 State Diagram
      2. 8.4.2 SLEEP
      3. 8.4.3 CONFIG/ACTIVE
      4. 8.4.4 Battery Supply Input (VBB) Under-voltage
      5. 8.4.5 LOW POWER MODE (LPM) State
      6. 8.4.6 LIMP HOME state
      7. 8.4.7 SPI Mode Operation
    5. 8.5 TPS2HC10S Registers
  10. 9 Application and Implementation
    1. 9.1 Application Information
    2. 9.2 Typical Application
      1. 9.2.1 Design Requirements
      2. 9.2.2 Detailed Design Procedure
        1. 9.2.2.1 Thermal Considerations
        2. 9.2.2.2 Configuring the Capacitive Charging Mode
    3. 9.3 Power Supply Recommendations
    4. 9.4 Layout
      1. 9.4.1 Layout Guidelines
      2. 9.4.2 Layout Example
  11. 10Device and Documentation Support
    1. 10.1 Documentation Support
      1. 10.1.1 Related Documentation
    2. 10.2 ドキュメントの更新通知を受け取る方法
    3. 10.3 サポート・リソース
    4. 10.4 Trademarks
    5. 10.5 静電気放電に関する注意事項
    6. 10.6 用語集
  12. 11Mechanical, Packaging, and Orderable Information
    1. 11.1 Tape and Reel Information

パッケージ・オプション

メカニカル・データ（パッケージ｜ピン）
サーマルパッド・メカニカル・データ
発注情報

8.4.2 SLEEP

The TPS2HCS10-Q1 output channels are typically among a large number of channels in an ECU. The ECUs need to consume uAs of of current while the car is in park mode or key-off mode. The SLEEP mode is lowest current consumption mode of the IC with current consumption of the order of a uA per channel. In the key-off mode for the car, the TPS2HCS10-Q1 can be in either LPM mode when at least one channel has to supply a load ECU or in the SLEEP state where all the channels are OFF and the digital/ VDD circuits are all powered off. The SPI command as a write to the SLEEP register places the device in the SLEEP state. The VDD and VBB pins of the IC are expected to be powered in the SLEEP state.

In the SLEEP state the device is mostly powered off, so that the overall current consumption from VBAT of the ECU is minimized for a totality of the high-side switch channels. In this mode the a low nCS pin can wake up the device and place the device in the CONFIG state ready for SPI communication. However, SPI communication (actual data communication) can happen only after the tREADY period.

GUID-20220804-SS0I-BKMW-G4TN-TQV5VB44ZRBX-low.svgFigure 8-10 Startup Communication Timing