SLUSAY8G
June 2012 – November 2025
TPS53318
,
TPS53319
PRODUCTION DATA
1
1
Features
2
Applications
3
Description
4
Device Comparison Table
5
Pin Configuration and Functions
6
Specifications
6.1
Absolute Maximum Ratings
6.2
ESD Ratings
6.3
Recommended Operating Conditions
6.4
Thermal Information
6.5
Electrical Characteristics
6.6
Typical Characteristics
6.7
TPS53319 Typical Characteristics
6.8
TPS53318 Typical Characteristics
7
Detailed Description
7.1
Overview
7.2
Functional Block Diagram
7.3
Feature Description
7.3.1
5-V LDO and VREG Start-Up
7.3.2
Adaptive On-Time D-CAP™ Integrated Circuit Control and Frequency Selection
7.3.3
Ramp Signal
7.3.4
Adaptive Zero Crossing
7.3.5
Output Discharge Control
7.3.6
Power Good
7.3.7
Current Sense, Overcurrent, and Short-Circuit Protection
7.3.8
Overvoltage and Undervoltage Protection
7.3.9
Redundant Overvoltage Protection (OVP)
7.3.10
UVLO Protection
7.3.11
Thermal Shutdown
7.3.12
Small Signal Model
7.3.13
External Component Selection Using All Ceramic Output Capacitors
7.4
Device Functional Modes
7.4.1
Enable, Soft Start, and Mode Selection
7.4.2
Auto-Skip Eco-mode Light Load Operation
7.4.3
Forced Continuous Conduction Mode
8
Application and Implementation
8.1
Application Information
8.2
Typical Applications
8.2.1
Application Using Bulk Output Capacitors, Redundant Overvoltage Protection Function (OVP) Disabled
8.2.1.1
Design Requirements
8.2.1.2
Detailed Design Procedure
8.2.1.2.1
Step One: Select Operation Mode and Soft-Start Time
8.2.1.2.2
Step Two: Select Switching Frequency
8.2.1.2.3
Step Three: Choose the Inductor
8.2.1.2.4
Step Four: Choose the Output Capacitor or Capacitors
8.2.1.2.5
Step Five: Determine the Value of R1 and R2
8.2.1.2.6
Step Six: Choose the Overcurrent Setting Resistor
8.2.1.3
Application Curves
8.2.2
Application Using Ceramic Output Capacitors, Redundant Overvoltage Protection Function (OVP) Enabled
8.2.2.1
Design Requirements
8.2.2.2
Detailed Design Procedure
8.2.2.2.1
External Component Selection Using All Ceramic Output Capacitors
8.2.2.2.2
Redundant Overvoltage Protection
8.2.2.3
Application Curves
8.3
Power Supply Recommendations
8.4
Layout
8.4.1
Layout Guidelines
8.4.2
Layout Example
9
Device and Documentation Support
9.1
Device Support
9.1.1
Development Support
9.2
Receiving Notification of Documentation Updates
9.3
Support Resources
9.4
Trademarks
9.5
Electrostatic Discharge Caution
9.6
Glossary
10
Revision History
11
Mechanical, Packaging, and Orderable Information
1
Features
New products available:
TPS548A28
and
TPS548A29
16V, 15A, synchronous converters with remote sense
Conversion input voltage range: 1.5V to 22V
VDD input voltage range: 4.5V to 25V
91% efficiency from 12V to 1.5V at 14A
Output voltage range: 0.6V to 5.5V
5V LDO output
Supports single-rail input
Integrated power MOSFETs with 8A (TPS53318) or 14A (TPS53319) of continuous output current
Auto-skip Eco-mode for light-load efficiency
< 110μA shutdown current
D-CAP™
integrated circuit mode with fast transient response
Selectable switching frequency from 250kHz to 1MHz with external resistor
Selectable auto-skip or PWM-only operation
Built-in 1% 0.6V reference
0.7ms, 1.4ms, 2.8ms and 5.6ms selectable internal voltage servo soft-start
Integrated boost switch
Pre-charged start-up capability
Adjustable overcurrent limit with thermal compensation
Overvoltage, undervoltage, UVLO and overtemperature protection
Supports all ceramic output capacitors
Open-drain power-good indication
Incorporates
NexFET™
power MOSFET block technology
22-pin QFN (DQP) package with
PowerPAD™
integrated circuit package