SLVS757E March   2007  – July 2022 TPS5450

PRODUCTION DATA  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Oscillator Frequency
      2. 7.3.2  Voltage Reference
      3. 7.3.3  Enable (ENA) and Internal Slow-Start
      4. 7.3.4  Undervoltage Lockout (UVLO)
      5. 7.3.5  Boost Capacitor (BOOT)
      6. 7.3.6  Output Feedback (VSENSE) and Internal Compensation
      7. 7.3.7  Voltage Feed-Forward
      8. 7.3.8  Pulse-Width-Modulation (PWM) Control
      9. 7.3.9  Overcurrent Limiting
      10. 7.3.10 Overvoltage Protection
      11. 7.3.11 Thermal Shutdown
    4. 7.4 Device Functional Modes
      1. 7.4.1 Operation near Minimum Input Voltage
      2. 7.4.2 Operation With ENA Control
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Switching Frequency
        2. 8.2.2.2 Output Voltage Setpoint
        3. 8.2.2.3 Input Capacitors
        4. 8.2.2.4 Output Filter Components
        5. 8.2.2.5 Inductor Selection
        6. 8.2.2.6 Capacitor Selection
        7.       43
        8. 8.2.2.7 Boot Capacitor
        9. 8.2.2.8 Catch Diode
        10. 8.2.2.9 Advanced Information
          1. 8.2.2.9.1 Output Voltage Limitations
          2. 8.2.2.9.2 Internal Compensation Network
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
    3. 10.3 Thermal Calculations
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Third-Party Products Disclaimer
    2. 11.2 Trademarks
    3. 11.3 Electrostatic Discharge Caution
    4. 11.4 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

8.2.1 Design Requirements

To begin the design process a few parameters must be decided upon. These requirements are typically determined at the system levels. This example is designed to the following known parameters:

Table 8-1 Design Parameters
DESIGN PARAMETER(1)EXAMPLE VALUE
Input voltage range10 V to 31 V
Output voltage5 V
Input ripple voltage400 mV
Output ripple voltage30 mV
Output current rating5 A
Operating frequency500 kHz
(1) As an additional constraint, the design is set up to be small size and low component height.