SLVS975C September   2009  – April 2018 TPS54318

PRODUCTION DATA.  

  1. 1 Features
  2. 2 Applications
  3. 3 Description
    1.     Device Images
      1.      Simplified Schematic
      2.      Efficiency vs Output Current
  4. 4 Revision History
  5. 5 Pin Configuration and Functions
    1.     Pin Functions
  6. 6 Specifications
    1. 6.1 Absolute Maximum Ratings
    2. 6.2 ESD Ratings
    3. 6.3 Recommended Operating Conditions
    4. 6.4 Thermal Information
    5. 6.5 Electrical Characteristics
    6. 6.6 Typical Characteristics
  7. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1  Fixed Frequency PWM Control
      2. 7.3.2  Slope Compensation and Output Current
      3. 7.3.3  Bootstrap Voltage (Boot) and Low Dropout Operation
      4. 7.3.4  Error Amplifier
      5. 7.3.5  Voltage Reference
      6. 7.3.6  Adjusting the Output Voltage
      7. 7.3.7  Enable and Adjusting Undervoltage Lockout
      8. 7.3.8  Soft-Start Pin
      9. 7.3.9  Sequencing
      10. 7.3.10 Constant Switching Frequency and Timing Resistor (RT/CLK Pin)
      11. 7.3.11 Overcurrent Protection
      12. 7.3.12 Frequency Shift
      13. 7.3.13 Reverse Overcurrent Protection
      14. 7.3.14 Synchronize Using the RT/CLK Pin
      15. 7.3.15 Power Good (PWRGD Pin)
      16. 7.3.16 Overvoltage Transient Protection
      17. 7.3.17 Thermal Shutdown
    4. 7.4 Device Functional Modes
      1. 7.4.1 Small Signal Model for Loop Response
      2. 7.4.2 Simple Small Signal Model for Peak Current Mode Control
      3. 7.4.3 Small Signal Model for Frequency Compensation
  8. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1  Step One: Select the Switching Frequency
        2. 8.2.2.2  Step Two: Select the Output Inductor
        3. 8.2.2.3  Step Three: Choose the Output Capacitor
        4. 8.2.2.4  Step Four: Select the Input Capacitor
        5. 8.2.2.5  Step Five: Minimum Load DC COMP Voltage
        6. 8.2.2.6  Step Six: Choose the Soft-Start Capacitor
        7. 8.2.2.7  Step Seven: Select the Bootstrap Capacitor
        8. 8.2.2.8  Step Eight: Undervoltage Lockout Threshold
        9. 8.2.2.9  Step Nine: Select Output Voltage and Feedback Resistors
          1. 8.2.2.9.1 Output Voltage Limitations
        10. 8.2.2.10 Step 10: Select Loop Compensation Components
        11. 8.2.2.11 Power Dissipation Estimate
      3. 8.2.3 Application Curves
  9. 9 Power Supply Recommendations
  10. 10Layout
    1. 10.1 Layout Guidelines
    2. 10.2 Layout Example
  11. 11Device and Documentation Support
    1. 11.1 Device Support
      1. 11.1.1 Custom Design With WEBENCH® Tools
      2. 11.1.2 Development Support
    2. 11.2 Trademarks
    3. 11.3 Electrostatic Discharge Caution
    4. 11.4 Glossary
  12. 12Mechanical, Packaging, and Orderable Information

6.5 Electrical Characteristics

–40°C ≤ TJ ≤ 150°C, 2.95 ≤ VVIN ≤ 6 V (unless otherwise noted) over operating free-air temperature range
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SUPPLY VOLTAGE (VIN)
VVIN Operating input voltage 2.95 6 V
VUVLO Internal under voltage lockout threshold No voltage hysteresis, rising and falling 2.6 2.8 V
IQ(vin) Shutdown supply current VEN = 0 V, TA = 25°C, 2.95 V ≤ VVIN ≤ 6 V 2 5 μA
Iq Quiescent current VVSENSE = 0.9 V, VVIN = 5 V, 25°C,
RT = 400 kΩ		 350 500 μA
ENABLE AND UVLO (EN)
VTH(en) Enable threshold Rising 1.16 1.25 1.37 V
Falling 1.18
IEN Input current Enable rising threshold + 50 mV –3.2 μA
Enable falling threshold – 50 mV –0.65
VOLTAGE REFERENCE (VSENSE)
VREF Voltage reference 2.95 V ≤ VVIN ≤ 6 V, –40°C <TJ< 150°C 0.795 0.803 0.811 V
MOSFET
RDS(HFET) High-side switch resistance (VBOOT – VPH) = 5 V 30 60 mΩ
(VBOOT – VPH) = 2.95 V 44 70
RDS(LFET) Low-side switch resistance VVIN = 5 V 30 60 mΩ
VVIN = 2.95 V 44 70
ERROR AMPLIFIER
IIN Input current 7 nA
gM(ea) Error amplifier transconductance –2 μA < ICOMP< 2 μA, VCOMP = 1 V 225 μS
gm(EA,ss) Error amplifier transconductance during soft-start –2 μA < ICOMP< 2 μA, VCOMP = 1 V,
VVSENSE = 0.4 V		 70 μS
ICOMP Error amplifier source/sink VCOMP = 1 V, 100 mV overdrive ±20 μA
gM COMP to ISWITCH transconductance 13 A/V
CURRENT LIMIT
ILIM Current limit threshold Instantaneous peak current 3.7 5.5 A
THERMAL SHUTDOWN
TSD Thermal Shutdown 175 °C
TSD(hyst) Hysteresis 15 °C
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK)
fSW Switching frequency range using RT mode 200 2000 kHz
fSW Switching frequency RRT = 400 kΩ 400 500 600 kHz
fSW Switching frequency range using CLK mode 300 2000 kHz
tMIN(CLK) Minimum CLK pulse width 75 ns
VRT/CLK RT/CLK voltage RRT/CLK = 400 kΩ 0.5 V
VIH(CLK) RT/CLK high threshold 1.6 2.2 V
VIL(CLK) RT/CLK low threshold 0.4 0.6 V
tDLY RT/CLK falling edge to PH rising edge delay fSW = 500 kHz with RRT resistor in series 90 ns
tLOCK(PLL) PLL lock-in time fSW = 500 kHz 14 μs
HIGH-SIDE POWER MOSFET (PH)
tON(min) Minimum on time Measured at 50% points on PH, IOUT = 3 60 ns
Measured at 50% points on PH, VVIN = 5 V,
IOUT = 0 A		 110
tOFF(min) Minimum off time Prior to skipping off pulses,
(VBOOT – VPH) = 2.95 V, IOUT = 3		 60 ns
tRISE Rise time VVIN = 5 V 1.5 V/ns
tFALL Fall time VVIN = 5 V 1.5 V/ns
BOOT (BOOT)
RBOOT BOOT charge resistance VVIN = 5 V 16 Ω
VUVLO(Boot) BOOT-PH UVLO VVIN = 2.95 V 2.1 V
SOFT-START (SS )
ICHG Charge current VSS = 0.4 V 1.8 μA
VSSxREF SS to reference crossover 98% nominal 0.9 V
VDSCHG(SS) SS discharge voltage (overload) VVSENSE = 0 V 20 μA
IDSCHG(SS) SS discharge current (UVLO, EN, thermal fault) VVIN = 5 V, VSS = 0.5 V 1.25 mA
POWER GOOD (PWRGD)
VTH(PG) VSENSE threshold VVSENSE falling (fault) 91% VREF
VVSENSE rising (good) 93%
VVSENSE rising (fault) 107%
VVSENSE falling (Good) 105%
VHYST(PG) Hysteresis VVSENSE falling 2%
IPH(lkg) Output high leakage VVSENSE = VREF, VPWRGD = 5.5 V 2 nA
RPG Power Good on-resistance 100 Ω
VOL Low-level output voltage IPWRGD = 3.5 mA 0.3 V
VMIN(PG) Minimum input voltage for valid output VPWRGD< 0.5 V , IOUT = 100 μA 1.2 1.6 V